Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2015.06–2016.09
RM19S0E _58 Vehicle Interior _051491 THEFT DETERRENT / KEYLESS ENTRY _0248300 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU - ECM communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are output. If output, troubleshoot the engine immobiliser DTCs first.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2799 Either condition is met (1 trip detection logic*):
·

A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly.

·

A communication code cannot be verified during communication between the ECM and transponder key ECU assembly.


·

Harness or connector

·

Transponder key ECU assembly

·

ECM


Either condition is met:
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal depressed, turn the ignition switch to ON). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the ignition switch is turned to ON after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2799 -

WIRING DIAGRAM

B255097E05
0.928,1.961 1.221,2.135 0.293,0.174 10 A74 0.928,2.107 1.280,2.267 0.352,0.160 10 ECM 5.731,0.465 6.125,0.653 0.394,0.188 10 EFIO 5.731,1.229 6.125,1.417 0.394,0.188 10 EFII 1.286,0.465 1.520,0.653 0.234,0.188 10 IMI 1.237,1.229 1.520,1.417 0.283,0.188 10 IMO 5.442,0.367 5.666,0.577 0.224,0.210 10 13 5.442,1.113 5.666,1.323 0.224,0.210 10 12 5.533,1.961 5.944,2.147 0.410,0.186 10 F54 5.533,2.107 7.033,2.417 1.500,0.310 10 Transponder Key ECU Assembly 1.594,0.381 1.772,0.563 0.178,0.181 10 11 1.594,1.127 1.783,1.309 0.188,0.181 10 10

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

When replacing the ECM, refer to the INITIALIZATION (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Start the engine.


b.

Wait 10 seconds or more.


c.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2799 is not output.


Result
Result Proceed to
OK A
NG (DTC B2799 is output) B
NG (Other DTCs are output) C



A

B

3.INSPECT ECM (TERMINAL IMO)

C

3.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

U158201E02
4.958,0.948 4.563,2.438 false 5.521,0.26 5.792,0.438 0.271,0.177 10 false A74 4.438,2.458 4.75,2.635 0.313,0.177 10 false IMO 0.521,4.01 0.885,4.188 0.365,0.177 10 false GND 1.563,3.135 1.76,3.281 0.198,0.146 10 false *b 0.177,0.198 0.375,0.385 0.198,0.188 10 false *a

Text in Illustration
*a Component with harness connected
(ECM)
*b Waveform

Measurement Condition
Item Content
Tester Connection A74-10 (IMO) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.

OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Terminal IMO stuck high (12 V) or Abnormal waveform C



A

4.INSPECT ECM (TERMINAL IMI)

B

7.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

13.REPLACE ECM
4.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

U158202E02
4.813,0.948 4.417,2.448 false 5.51,0.271 5.781,0.448 0.271,0.177 10 false A74 4.333,2.469 4.646,2.646 0.313,0.177 10 false IMI 0.531,4.01 0.896,4.188 0.365,0.177 10 false GND 2.719,3.135 2.917,3.281 0.198,0.146 10 false *b 0.167,0.208 0.365,0.396 0.198,0.188 10 false *a

Text in Illustration
*a Component with harness connected
(ECM)
*b Waveform

Measurement Condition
Item Content
Tester Connection A74-11 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.

OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Not output waveform or abnormal waveform B



A

5.REGISTER ECU COMMUNICATION ID

B

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
5.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID (Refer to Service Bulletin).



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with an already registered vehicle key.

OK:

Engine starts normally.




OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

13.REPLACE ECM
7.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.
U158075E01
0.304,0.957 0.569,1.138 0.264,0.181 10 A74 0.075,0.079 0.245,0.239 0.170,0.161 10 *a 1.983,1.744 2.278,1.886 0.295,0.142 10 IMO 2.356,0.813 2.147,1.727 false

Disconnect the A74 ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Result
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) B

Text in Illustration
*a Front view of wire harness connector
(to ECM)



A

8.CHECK HARNESS AND CONNECTOR (ECM - TRANSPONDER KEY ECU ASSEMBLY AND BODY GROUND)

B

13.REPLACE ECM
8.CHECK HARNESS AND CONNECTOR (ECM - TRANSPONDER KEY ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the F54 transponder key ECU assembly connector.


b.

Disconnect the A74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F54-12 (EFII) - A74-10 (IMO) Always Below 1 Ω
F54-12 (EFII) - Body ground Always 10 kΩ or higher




OK

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly (Refer to Service Bulletin).



NEXT

10.REGISTER KEY
10.REGISTER KEY
a.

Reregister the key (Refer to Service Bulletin).



NEXT

11.REGISTER ECU COMMUNICATION ID
11.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID (Refer to Service Bulletin).



NEXT

12.CHECK WHETHER ENGINE STARTS
12.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with an already registered vehicle key.

OK:

Engine starts normally.


Result
Result Proceed to
OK A
NG (for 2NZ-FE) B
NG (for 1NZ-FE) C



A

END (TRANSPONDER KEY ECU WAS DEFECTIVE)

B

C

13.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

HINT:




NEXT

14.REGISTER ECU COMMUNICATION ID
14.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID (Refer to Service Bulletin).



NEXT

15.CHECK WHETHER ENGINE STARTS
15.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with the key.

OK:

Engine starts normally.




OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY