Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2014.07
RM19S0E _58 Vehicle Interior _051491 THEFT DETERRENT / KEYLESS ENTRY _0248300 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key coil, the transponder key ECU assembly stores this DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2784 The antenna coil built into the transponder key coil is open or shorted (determined by communication with transponder key ECU assembly) (1 trip detection logic*).
·

Harness or connector

·

Transponder key coil

·

Transponder key ECU assembly


Insert the key into the ignition key cylinder.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2784 Antenna Coil Status

WIRING DIAGRAM

B329324E51
5.552,2.542 6.01,2.74 0.458,0.198 10 false F54 5.542,2.698 6.906,3.219 1.365,0.521 10 false Transponder Key ECU Assembly 1.292,3.042 1.75,3.24 0.458,0.198 10 false F135 1.281,3.188 2.75,3.49 1.469,0.302 10 false Transponder Key Coil 2.792,0.76 3.552,1.052 0.76,0.292 10 false ANT1 2.781,1.948 3.542,2.24 0.76,0.292 10 false ANT2 5.667,0.896 6.427,1.188 0.76,0.292 10 false ANT1 5.677,2.063 6.438,2.354 0.76,0.292 10 false ANT2 5.51,0.802 5.75,1.042 0.24,0.24 10 false 4 5.427,1.958 5.667,2.198 0.24,0.24 10 false 15 3.25,0.75 3.49,0.99 0.24,0.24 10 false 1 3.229,1.948 3.469,2.188 0.24,0.24 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.




OK

NG

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the transponder key coil.



NEXT

4.CLEAR DTC
4.CLEAR DTC

NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result
Result Proceed to
B2784 is not output A
B2784 is output B


A

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

B

6.CHECK TRANSPONDER KEY COIL (OUTPUT)
6.CHECK TRANSPONDER KEY COIL (OUTPUT)
a.

Using an oscilloscope, check the waveform.

U158236E02
3.333,0.781 3.229,1.063 false 3.823,0.771 3.927,1.052 false 3.021,1.083 3.438,1.271 0.417,0.188 10 false ANT2 3.844,1.073 4.26,1.26 0.417,0.188 10 false ANT1 3.417,0.094 3.813,0.25 0.396,0.156 10 false F135 6.563,4.542 6.979,4.729 0.417,0.188 10 false GND 6.563,2.469 6.979,2.656 0.417,0.188 10 false GND 0.115,0.115 0.344,0.313 0.229,0.198 10 false *a 0.979,3.521 1.208,3.719 0.229,0.198 10 false *c 0.979,1.448 1.208,1.646 0.229,0.198 10 false *b

Text in Illustration
*a Component with harness connected
(Transponder Key Coil)
*b Waveform 1
*c Waveform 2 - -

Waveform 1
Item Content
Tester Connection F135-1 (ANT1) - Body ground
Tool Setting 20 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder

Waveform 2
Item Content
Tester Connection F135-5 (ANT2) - Body ground
Tool Setting 20 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder

OK:

Waveform is similar to that shown in the illustration




OK

NG

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL AND BODY GROUND)
7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL AND BODY GROUND)
a.

Disconnect the F54 transponder key ECU assembly connector.


b.

Disconnect the F135 transponder key coil connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
F54-4 (ANT1) - F135-1 (ANT1) Always Below 1 Ω
F54-15 (ANT2) - F135-5 (ANT2) Always Below 1 Ω
F54-4 (ANT1) or F135-1 (ANT1) - Body ground Always 10 kΩ or higher
F54-15 (ANT2) or F135-5 (ANT2) - Body ground Always 10 kΩ or higher



OK

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one (Refer to Service Bulletin).

NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly. Refer to Service Bulletin.




NEXT

9.CLEAR DTC
9.CLEAR DTC

NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result
Result Proceed to
B2784 is not output A
B2784 is output B


A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B