Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2014.07
RM19S0E _58 Vehicle Interior _051492 LIGHTING (INT) _0248303 LIGHTING SYSTEM U

LIGHTING (INT)  LIGHTING SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU


U158735E02
1.01,0.938 1.208,1.083 0.198,0.146 10 false 3D 0.292,0.177 0.438,0.323 0.146,0.146 10 false *1 0.167,6.448 0.333,6.604 0.167,0.156 10 false *2 1.531,3.854 1.729,4 0.198,0.146 10 false 3D 3.802,0.771 4.031,0.938 0.229,0.167 10 false MB 3.802,2.854 4.031,3.01 0.229,0.156 10 false MB 1.01,1.573 1.208,1.729 0.198,0.156 10 false 3C 4.01,3.854 4.219,4 0.208,0.146 10 false 3C 6.385,0.938 6.583,1.083 0.198,0.146 10 false 3B 6.385,1.563 6.583,1.708 0.198,0.146 10 false 3A 5.469,5.208 5.667,5.354 0.198,0.146 10 false 3A 5.531,6.646 5.792,6.792 0.26,0.146 10 false F76 5.229,7.615 5.5,7.76 0.271,0.146 10 false F76 1.688,5.219 1.885,5.365 0.198,0.146 10 false 3B 1.01,2.104 1.208,2.26 0.198,0.156 10 false 3F 6.052,3.854 6.24,4 0.188,0.146 10 false 3F 0.156,6.688 0.323,6.844 0.167,0.156 10 false *A 3.646,6.646 3.813,6.802 0.167,0.156 10 false *B 1.958,6.635 2.219,6.781 0.26,0.146 10 false F76 1.156,6.635 1.51,6.781 0.354,0.146 10 false F136 1.635,7.656 1.99,7.802 0.354,0.146 10 false F136

Text in Illustration
*A Main Body ECU 2 Connector Type *B Main Body ECU 1 Connector Type
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU

a.

Remove the main body ECU.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-3 (BCYL) - Body ground - Battery power supply Always 11 to 14 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-29 (ACC) - Body ground - Ignition power supply (ACC signal) Ignition switch ACC 11 to 14 V
MB-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply (IG signal) Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reinstall the main body ECU.


d.

Measure the voltage resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F76-6 (RCTY) - Body ground G - Body ground Rear door courtesy light switch RH signal Rear door RH opened Below 1 V
Rear door RH closed Pulse generation
F76-18 (LSFR) - Body ground LG - Body ground Front door RH unlock detection switch signal Front door RH locked Pulse generation
Front door RH unlocked Below 1 V
F76-19 (FRCY) - Body ground Y - Body ground Front door courtesy light switch RH signal Front door RH opened Below 1 V
Front door RH closed Pulse generation
F76-24 (LCTY) - Body ground L - Body ground Rear door courtesy light switch LH signal Rear door LH opened Below 1 V
Rear door LH closed Pulse generation
3A-5 (BCYL) - Body ground SB - Body ground Battery power supply Always 11 to 14 V
3B-6 (ILE) - Body ground B - Body ground Illumination signal Map light switch in DOOR position and map light assembly comes on Below 1 V
Map light switch in DOOR position and map light assembly goes off 11 to 14 V
3D-6 (BCTL) - Body ground L - Body ground No. 2 room light power supply Always 11 to 14 V
3D-35 (BCTY) - Body ground B - Body ground Back door courtesy switch signal Back door opened Below 1 V
Back door closed 11 to 14 V*6
3D-36 (FLCY) - Body ground L - Body ground Front door courtesy light switch LH signal Front door LH opened Below 1 V
Front door LH closed Pulse generation

HINT:

If the result is not as specified, the main body ECU or instrument panel junction block assembly may have a malfunction.