Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor) › from 2014.07
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248314 AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor)  SRS Warning Light does not Come ON  


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT BATTERY
a.

Measure the voltage of the battery.

Standard Voltage:
Tester Connection Condition Specified Condition
Battery Always 11 to 14 V


Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

2.CHECK CONNECTION OF CONNECTORS

B

C

2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and the combination meter assembly.

OK:

The connectors are properly connected.




OK

3.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER ASSEMBLY)

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER ASSEMBLY)
a.
U158626E01
1.641,0.073 1.829,0.229 0.188,0.156 10 F1 0.521,1.224 0.4,1.644 false 0.299,1.673 0.511,1.829 0.213,0.156 10 ET 2.768,1.224 2.871,1.644 false 2.752,1.673 3.041,1.829 0.289,0.156 10 IG+ 0.2,0.098 0.413,0.254 0.213,0.156 10 *a

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the connectors from the combination meter assembly and airbag sensor assembly.


d.

Connect the cable to the negative battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-39 (IG+) - F1-21 (ET) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

4.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Connect the connector to the combination meter assembly.


d.

Connect the cable to the negative battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

The SRS warning light goes off after the primary check period and comes on again after approximately 10 seconds.


HINT:

The primary check period lasts for approximately 6 seconds after the ignition switch is turned to ON.




OK

NG

REPLACE COMBINATION METER ASSEMBLY