Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248314 AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor) D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor)  DTC CHECK / CLEAR  


DTC CHECK (USING SST CHECK WIRE)


a.
U158309E01
0.08,0.076 0.242,0.244 0.161,0.168 10 *1 1.376,1.821 1.611,1.969 0.234,0.148 10 CG 1.622,1.081 1.501,1.785 false 0.306,1.16 0.578,1.342 0.272,0.181 10 F4

Check for DTCs (Present DTC).

i.

Turn the ignition switch to ON, and wait for approximately 60 seconds.


ii.

Using SST, connect terminals TC and CG of the DLC3.

Text in Illustration
*1 DLC3

SST
09843-18040  

NOTICE:

Connect the terminals to the correct positions to avoid a malfunction.




b.

Check for DTCs (Past DTC).

i.

Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  

NOTICE:

Connect the terminals to the correct positions to avoid a malfunction.



ii.

Turn the ignition switch to ON, and wait for approximately 60 seconds.



c.

Read the DTCs.

C355175E01
0.323,0.219 2.896,0.438 2.573,0.219 10 false Normal System Code (without Past DTC) 0.927,0.719 1.802,0.917 0.875,0.198 10 false 0.25 seconds 1,1.781 1.875,1.979 0.875,0.198 10 false 0.25 seconds 0.75,1.063 1.052,1.24 0.302,0.177 10 false ON 0.698,1.438 1,1.615 0.302,0.177 10 false OFF 0.406,2.208 2.979,2.427 2.573,0.219 10 false Normal System Code (with Past DTC) 0.99,2.5 1.865,2.698 0.875,0.198 10 false 0.75 seconds 1.188,3.531 2.063,3.729 0.875,0.198 10 false 0.25 seconds 0.771,2.823 1.073,3 0.302,0.177 10 false ON 0.708,3.229 1.01,3.406 0.302,0.177 10 false OFF 3.698,0.229 5.625,0.448 1.927,0.219 10 false DTC (Example DTC 11 and 31) 4.229,1.177 4.531,1.354 0.302,0.177 10 false ON 4.146,1.458 4.448,1.635 0.302,0.177 10 false OFF 4.583,0.865 4.802,1.042 0.219,0.177 10 false 0.5 4.948,0.865 5.167,1.042 0.219,0.177 10 false 2.5 5.781,0.854 6,1.031 0.219,0.177 10 false 4.0 4.698,1.719 4.917,1.896 0.219,0.177 10 false 1.5 5.167,1.719 5.385,1.896 0.219,0.177 10 false 0.5 6.135,1.708 6.646,1.896 0.51,0.188 10 false Repeat 4.604,2.021 5.083,2.208 0.479,0.188 10 false DTC 11 5.26,2.01 5.74,2.198 0.479,0.188 10 false DTC 31 5.979,1.979 6.625,2.219 0.646,0.24 10 false (seconds)

i.

Observe the SRS warning light and read the blinking patterns of the DTCs. As examples, the blinking patterns for the normal system code and DTCs 11 and 31 are shown in the illustration on the left.

·

Normal system code indication (without past DTC)

The SRS warning light blinks twice per second.

·

Normal system code indication (with past DTC)

When the past DTC is stored in the airbag sensor assembly, the light blinks once per second.

·

DTC indication

The first blinking pattern indicates the first digit DTC. The second blinking pattern occurs after a 1.5-second pause.


If there are two or more DTCs, there is a 2.5-second pause between each DTC. After all DTCs are shown, there is a 4.0-second pause, and they are all repeated.

HINT:
·

If 2 or more malfunctions are found, the indication begins with the lowest numbered DTC.

·

If DTCs are indicated without connecting the terminals, proceed to the "TC and CG Terminal Circuit" (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>TC and CG Terminal Circuit).






DTC CLEAR (USING SST CHECK WIRE)


a.

Clear the DTCs.

i.

When the ignition switch is turned off, the DTCs are cleared.

HINT:

Depending on the DTCs, the DTCs may not all be cleared by turning off the ignition switch. In this case, proceed to the next operation.



ii.

Using SST, connect terminals TC and CG of the DLC3, and then turn the ignition switch to ON.

SST
09843-18040  


iii.

Disconnect terminal TC of the DLC3 within 3 to 10 seconds of the DTCs being output, and check that the SRS warning light comes on after 3 seconds.


iv.

Within 2 to 4 seconds of the SRS warning light coming on, connect terminals TC and CG of the DLC3.


v.

The SRS warning light goes off within 2 to 4 seconds of connecting terminals TC and CG of the DLC3. Then, disconnect terminal TC within 2 to 4 seconds of the SRS warning light going off.


vi.

The SRS warning light comes on again within 2 to 4 seconds of disconnecting terminal TC. Then, reconnect terminals TC and CG within 2 to 4 seconds of the SRS warning light coming on.


vii.

Check that the SRS warning light goes off within 2 to 4 seconds of connecting terminals TC and CG of the DLC3. Also check that the normal system code is output within 1 second of the SRS warning light going off.

If DTCs are not cleared, repeat these procedures until the DTCs are cleared.

C109537E43
0.26,0.521 1.219,0.708 0.958,0.188 10 false Ignition Switch 0.24,1.417 1.479,1.604 1.24,0.188 10 false DLC3 (TC and CG) 0.229,2.052 1.635,2.26 1.406,0.208 10 false SRS Warning Light* 3.74,1.677 3.979,1.885 0.24,0.208 10 false 0.5 0.333,2.677 1.635,2.854 1.302,0.177 10 false T1: Preparation time 0.333,2.938 2.229,3.146 1.896,0.208 10 false T2: approximately 6 seconds 0.333,3.229 1.521,3.427 1.188,0.198 10 false T3: 3 to 5 seconds 0.333,3.5 1.594,3.708 1.26,0.208 10 false T4: 3 to 10 seconds 0.333,3.781 1.521,3.958 1.188,0.177 10 false T5: 2 to 4 seconds 0.344,4.063 1.531,4.24 1.188,0.177 10 false T6: 1 to 5 seconds 0.344,4.333 1.656,4.521 1.313,0.188 10 false T7: within 1 second 2.573,4.281 6.521,4.5 3.948,0.219 10 false *: The past DTC in the illustration shows DTC 21 as an example. 2.448,3.281 2.646,3.51 0.198,0.229 10 false T1 3.177,1.688 3.406,1.896 0.229,0.208 10 false 0.5 1.698,1.948 1.948,2.146 0.25,0.198 10 false ON 1.656,0.781 2.094,0.979 0.438,0.198 10 false LOCK 1.698,1.583 2.094,1.771 0.396,0.188 10 false Short 1.688,1.25 2.104,1.427 0.417,0.177 10 false Open 1.646,0.406 1.906,0.573 0.26,0.167 10 false ON 1.698,2.302 2.021,2.479 0.323,0.177 10 false OFF 3.76,2.635 4,2.844 0.24,0.208 10 false 1.5 6.042,3.781 6.781,3.99 0.74,0.208 10 false (seconds) 5.865,1.698 6.156,1.906 0.292,0.208 10 false 0.25 6.25,1.698 6.563,1.865 0.313,0.167 10 true 0.25 3.271,3.281 3.469,3.51 0.198,0.229 10 false T3 3.76,3.281 3.958,3.51 0.198,0.229 10 false T4 2.854,3.281 3.052,3.51 0.198,0.229 10 false T2 4.167,3.281 4.365,3.51 0.198,0.229 10 false T5 4.427,3.281 4.625,3.51 0.198,0.229 10 false T6 4.677,3.281 4.875,3.51 0.198,0.229 10 false T5 4.938,3.281 5.135,3.51 0.198,0.229 10 false T6 5.198,3.281 5.396,3.51 0.198,0.229 10 false T5 5.719,3.281 5.917,3.51 0.198,0.229 10 false T5 5.458,3.281 5.656,3.51 0.198,0.229 10 false T6 5.948,3.281 6.146,3.51 0.198,0.229 10 false T7




DTC CHECK


a.

Check for DTCs.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Check the DTCs by following the prompts on the tester screen.

HINT:

Refer to the intelligent tester operator's manual for further details.




b.

Clear DTCs.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Clear the DTCs by following the prompts on the tester screen.

HINT:

Refer to the intelligent tester operator's manual for further details.