The front airbag sensor circuit consists of the airbag sensor assembly and front airbag sensor.
The front airbag sensor detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.
These DTCs are stored when a malfunction is detected in the front airbag sensor circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B161C/9A
B161D/9A |
·
The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor circuit. ·
Front airbag sensor malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor ·
Airbag sensor assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly and front airbag sensor. Also disconnect the connectors that link the engine room main wire and instrument panel wire.
Check that the terminals of connectors are not damaged.
The terminals are not deformed or damaged.
OK
NG
Connect the connectors that link the engine room main wire and instrument panel wire.
| *1 | Front Airbag Sensor | *2 | Airbag Sensor Assembly |
| *3 | Connector B | *4 | Connector E |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
*b | Front view of wire harness connector
(to Front Airbag Sensor) |
Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A20-2 (+SL) - A20-1 (-SL) | Always | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A20-2 (+SL) - A20-1 (-SL) | Always | 1 MΩ or higher |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *a | Front view of wire harness connector
(to Front Airbag Sensor) |
OK
NG
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A20-2 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| A20-1 (-SL) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *a | Front view of wire harness connector
(to Front Airbag Sensor) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A20-2 (+SL) - Body ground | Always | 1 MΩ or higher |
| A20-1 (-SL) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *a | Front view of wire harness connector
(to Front Airbag Sensor) |
OK
NG
Connect the connector to the airbag sensor assembly.
Temporarily replace the front airbag sensor with a new one.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B161C/9A or B161D/9A is not output. | A |
| DTC B161C/9A or B161D/9A is output. | B |
Codes other than DTCs B161C/9A and B161D/9A may be output at this time, but they are not related to this check.
Reinstall the former front airbag sensor, and connect the connector.
A
B
Disconnect the instrument panel wire connector from the engine room main wire.
| *1 | Front Airbag Sensor | *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire | *4 | Instrument Panel Wire |
| *5 | Connector B | *6 | Connector C |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
*b | Front view of wire harness connector
(to Engine Room Main Wire) |
The service wire has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AF1-1 (+SL) - AF1-2 (-SL) | Always | Below 1 Ω |
OK
NG
Disconnect the instrument panel wire connector from the engine room main wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AF1-1 (+SL) - AF1-2 (-SL) | Always | 1 MΩ or higher |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *5 | Connector C |
| *a | Front view of wire harness connector
(to Engine Room Main Wire) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect the instrument panel wire connector from the engine room main wire.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| AF1-1 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| AF1-2 (-SL) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *5 | Connector C |
| *a | Front view of wire harness connector
(to Engine Room Main Wire) |
OK
NG
Disconnect the instrument panel wire connector from the engine room main wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AF1-1 (+SL) - Body ground | Always | 1 MΩ or higher |
| AF1-2 (-SL) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *5 | Connector C |
| *a | Front view of wire harness connector
(to Engine Room Main Wire) |
OK
NG