Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248330 AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)  B1835/58  Short in Curtain Shield Squib LH Circuit  B1836/58  Open in Curtain Shield Squib LH Circuit  B1837/58  Short to GND in Curtain Shield Squib LH Circuit  B1838/58  Short to B+ in Curtain Shield Squib LH Circuit  


DESCRIPTION

The curtain shield squib LH circuit consists of the airbag sensor assembly and curtain shield airbag assembly LH.

The circuit instructs SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1835/58
·

The airbag sensor assembly receives a line short circuit signal in the curtain shield squib LH circuit during primary check.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Curtain shield airbag assembly LH (Curtain shield squib LH)

·

Airbag sensor assembly


B1836/58
·

The airbag sensor assembly receives an open circuit signal in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction


B1837/58
·

The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction


B1838/58
·

The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C222225E45
4.605,4.853 6.168,5.012 1.563,0.159 10 Airbag Sensor Assembly 1.05,3.71 3.355,4.039 2.304,0.329 10 Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH) 1.05,3.542 1.321,3.686 0.270,0.144 10 K27 4.456,2.124 4.563,2.275 0.107,0.151 10 7 4.456,2.953 4.551,3.098 0.095,0.145 10 6 2.718,2.128 2.821,2.272 0.103,0.144 10 1 2.718,2.95 2.816,3.101 0.098,0.151 10 2 4.605,4.686 4.881,4.837 0.276,0.151 10 K33 4.704,2.217 5.084,2.358 0.380,0.141 10 ICL+ 4.704,3.053 5.049,3.193 0.345,0.140 10 ICL- 2.224,2.13 2.612,2.269 0.387,0.139 10 ICL+ 2.224,2.952 2.583,3.099 0.359,0.147 10 ICL-

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
C249202E03
0.865,1.552 0.865,2.417 false 1.365,0.979 1.458,1.406 false 0.958,1.625 1.083,1.781 0.125,0.156 10 false D 1.156,1.625 1.281,1.781 0.125,0.156 10 false C 1.552,1.625 1.677,1.781 0.125,0.156 10 false B 1.875,1.385 2,1.542 0.125,0.156 10 false A 0.802,2.427 0.979,2.583 0.177,0.156 10 false *1 1.219,0.854 1.375,1 0.156,0.146 10 false *3 1.74,1.969 1.938,2.135 0.198,0.167 10 false *2

Check that the connectors are properly connected to the curtain shield airbag assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the curtain shield airbag assembly LH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the curtain shield airbag assembly LH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH)
*2 Airbag Sensor Assembly
*3 Floor Wire



OK

2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)

NG

REPLACE FLOOR WIRE

2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)
SST
09843-18061  

a.
U158504E02
2.479,2.24 2.708,2.24 false 1.167,0.906 1.167,1.396 false 1.094,1.406 1.24,1.552 0.146,0.146 10 false *1 1.865,1.344 2.01,1.521 0.146,0.177 10 false *2 1.281,0.979 1.396,1.135 0.115,0.156 10 false D 1.479,0.979 1.615,1.146 0.135,0.167 10 false C 0.927,1.646 1.073,1.792 0.146,0.146 10 false *a 1.198,1.979 1.385,2.146 0.188,0.167 10 false *3 2.76,2.156 3.073,2.302 0.313,0.146 10 false SST 1.156,2.229 1.438,2.406 0.281,0.177 10 false K27

Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag assembly LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.


Text in Illustration
*1 Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH)
*2 Airbag Sensor Assembly
*3 Connector C
*a Front view of wire harness connector
(to Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH))

HINT:

Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.




OK

NG

3.CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB LH CIRCUIT)
3.CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB LH CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect SST from connector C.


d.
U158505E02
0.854,0.896 0.854,1.25 false 2.104,2.292 1.802,2.042 true 2.281,2.292 2.542,2.052 true 1.313,0.479 1.417,0.76 false 0.969,0.969 1.094,1.125 0.125,0.156 10 false D 1.167,0.969 1.292,1.125 0.125,0.156 10 false C 1.552,0.969 1.677,1.125 0.125,0.156 10 false B 1.896,0.729 2.021,0.885 0.125,0.156 10 false A 0.781,1.25 0.927,1.396 0.146,0.146 10 false *1 1.167,0.313 1.333,0.458 0.167,0.146 10 false *3 1.75,1.302 1.927,1.458 0.177,0.156 10 false *2 0.979,1.615 1.146,1.781 0.167,0.167 10 false *a 1.385,2.229 1.573,2.375 0.188,0.146 10 false *4 1.458,1.917 1.792,2.073 0.333,0.156 10 false ICL+ 2.583,1.938 2.896,2.094 0.313,0.156 10 false ICL- 1.365,2.51 1.646,2.677 0.281,0.167 10 false K27

Disconnect the floor wire from the airbag sensor assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K27-1 (ICL+) - Body ground Ignition switch ON Below 1 V
K27-2 (ICL-) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K27-1 (ICL+) - K27-2 (ICL-) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K27-1 (ICL+) - Body ground Always 1 MΩ or higher
K27-2 (ICL-) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K27-1 (ICL+) - K27-2 (ICL-) Always 1 MΩ or higher


Text in Illustration
*1 Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH)
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Connector C
*a Front view of wire harness connector
(to Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH))




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the curtain shield airbag assembly LH and airbag sensor assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.


HINT:

Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.




OK

NG