Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248330 AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)  B161C/9A  Lost Communication with Front Satellite Sensor Bus Center  B161D/9A  Front Satellite Sensor Bus Center Initialization Incomplete  


DESCRIPTION

The front airbag sensor circuit consists of the airbag sensor assembly and front airbag sensor.

The front airbag sensor detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor circuit.

DTC No. DTC Detection Condition Trouble Area
B161C/9A
B161D/9A
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor circuit.

·

Front airbag sensor malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor

·

Airbag sensor assembly



WIRING DIAGRAM

C234055E36
0.406,3.823 0.708,4 0.302,0.177 10 false A20 0.406,3.979 1.708,4.156 1.302,0.177 10 false Front Airbag Sensor 5.448,3.813 5.74,3.99 0.292,0.177 10 false F16 5.448,3.979 7.042,4.229 1.594,0.25 10 false Airbag Sensor Assembly 3.438,1.354 3.708,1.521 0.271,0.167 10 false AF1 3.427,2.521 3.719,2.698 0.292,0.177 10 false AF1 3.521,1.125 3.635,1.333 0.115,0.208 10 false 1 3.51,2.313 3.635,2.49 0.125,0.177 10 false 2 1.333,1.323 1.604,1.5 0.271,0.177 10 false +SL 1.365,2.5 1.625,2.708 0.26,0.208 10 false -SL 5.646,2.5 5.885,2.688 0.24,0.188 10 false -SL 5.646,1.323 5.927,1.51 0.281,0.188 10 false +SL 1.74,1.219 1.865,1.385 0.125,0.167 10 false 2 1.74,2.385 1.865,2.573 0.125,0.188 10 false 1 5.344,1.229 5.521,1.406 0.177,0.177 10 false 30 5.333,2.396 5.521,2.583 0.188,0.188 10 false 28

PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and front airbag sensor. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK FRONT AIRBAG SENSOR CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT AIRBAG SENSOR CIRCUIT (OPEN)
a.

Connect the connectors that link the engine room main wire and instrument panel wire.

U158499E02
4.469,1.302 4.469,1.479 false 4.542,1.104 4.708,1.344 true 4.375,1.073 4.208,1.313 true 6.333,0.958 6.51,1.208 true 6.146,0.958 5.969,1.208 true 0.542,0.594 0.667,0.75 0.125,0.156 10 false F 1.823,0.594 1.948,0.75 0.125,0.156 10 false A 0.813,0.833 0.938,0.99 0.125,0.156 10 false E 1.125,0.833 1.25,0.99 0.125,0.156 10 false D 1.25,0.833 1.375,0.99 0.125,0.156 10 false C 1.531,0.833 1.656,0.99 0.125,0.156 10 false B 0.198,1.063 0.354,1.219 0.156,0.156 10 false *1 1.708,1.333 1.865,1.49 0.156,0.156 10 false *2 5.479,0.75 5.74,0.927 0.26,0.177 10 false A20 3.271,0.75 3.531,0.927 0.26,0.177 10 false F16 5.458,0.083 5.667,0.271 0.208,0.188 10 false *b 5.646,0.396 5.854,0.583 0.208,0.188 10 false *4 3.177,0.094 3.385,0.281 0.208,0.188 10 false *a 3.354,0.406 3.563,0.594 0.208,0.188 10 false *3 4.385,1.5 4.594,1.688 0.208,0.188 10 false *5 4.625,1.354 4.917,1.521 0.292,0.167 10 false +SL 4.063,1.333 4.323,1.5 0.26,0.167 10 false -SL 6.427,1.219 6.719,1.385 0.292,0.167 10 false +SL 5.844,1.219 6.104,1.385 0.26,0.167 10 false -SL

Text in Illustration
*1 Front Airbag Sensor *2 Airbag Sensor Assembly
*3 Connector B *4 Connector E
*5 Service Wire - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor)


b.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-2 (+SL) - A20-1 (-SL) Always Below 1 Ω




OK

3.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT)

NG

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
3.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT)
a.
U158498E01
0.684,0.689 0.812,0.847 0.128,0.158 10 F 2.248,0.689 2.376,0.847 0.128,0.158 10 A 1.022,0.921 1.150,1.080 0.128,0.158 10 E 1.4,0.921 1.528,1.080 0.128,0.158 10 D 1.538,0.921 1.666,1.080 0.128,0.158 10 C 1.916,0.921 2.044,1.080 0.128,0.158 10 B 0.272,1.175 0.445,1.328 0.174,0.153 10 *1 2.116,1.557 2.289,1.710 0.174,0.153 10 *2 1.257,2.275 1.521,2.456 0.264,0.181 10 A20 2.351,2.463 2.56,2.873 false 2.096,2.463 1.886,2.873 false 2.387,2.906 2.680,3.059 0.292,0.154 10 +SL 1.751,2.906 1.993,3.059 0.242,0.154 10 -SL 1.193,1.873 1.367,2.026 0.174,0.153 10 *3 0.987,1.65 1.161,1.803 0.174,0.153 10 *a

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-2 (+SL) - A20-1 (-SL) Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor
*2 Airbag Sensor Assembly
*3 Connector E
*a Front view of wire harness connector
(to Front Airbag Sensor)



OK

4.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO B+)

NG

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
4.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO B+)
a.
U158498E01
0.684,0.689 0.812,0.847 0.128,0.158 10 F 2.248,0.689 2.376,0.847 0.128,0.158 10 A 1.022,0.921 1.150,1.080 0.128,0.158 10 E 1.4,0.921 1.528,1.080 0.128,0.158 10 D 1.538,0.921 1.666,1.080 0.128,0.158 10 C 1.916,0.921 2.044,1.080 0.128,0.158 10 B 0.272,1.175 0.445,1.328 0.174,0.153 10 *1 2.116,1.557 2.289,1.710 0.174,0.153 10 *2 1.257,2.275 1.521,2.456 0.264,0.181 10 A20 2.351,2.463 2.56,2.873 false 2.096,2.463 1.886,2.873 false 2.387,2.906 2.680,3.059 0.292,0.154 10 +SL 1.751,2.906 1.993,3.059 0.242,0.154 10 -SL 1.193,1.873 1.367,2.026 0.174,0.153 10 *3 0.987,1.65 1.161,1.803 0.174,0.153 10 *a

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A20-2 (+SL) - Body ground Ignition switch ON Below 1 V
A20-1 (-SL) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 Front Airbag Sensor
*2 Airbag Sensor Assembly
*3 Connector E
*a Front view of wire harness connector
(to Front Airbag Sensor)



OK

5.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
5.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)
a.
U158498E01
0.684,0.689 0.812,0.847 0.128,0.158 10 F 2.248,0.689 2.376,0.847 0.128,0.158 10 A 1.022,0.921 1.150,1.080 0.128,0.158 10 E 1.4,0.921 1.528,1.080 0.128,0.158 10 D 1.538,0.921 1.666,1.080 0.128,0.158 10 C 1.916,0.921 2.044,1.080 0.128,0.158 10 B 0.272,1.175 0.445,1.328 0.174,0.153 10 *1 2.116,1.557 2.289,1.710 0.174,0.153 10 *2 1.257,2.275 1.521,2.456 0.264,0.181 10 A20 2.351,2.463 2.56,2.873 false 2.096,2.463 1.886,2.873 false 2.387,2.906 2.680,3.059 0.292,0.154 10 +SL 1.751,2.906 1.993,3.059 0.242,0.154 10 -SL 1.193,1.873 1.367,2.026 0.174,0.153 10 *3 0.987,1.65 1.161,1.803 0.174,0.153 10 *a

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-2 (+SL) - Body ground Always 1 MΩ or higher
A20-1 (-SL) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor
*2 Airbag Sensor Assembly
*3 Connector E
*a Front view of wire harness connector
(to Front Airbag Sensor)



OK

6.CHECK FRONT AIRBAG SENSOR

NG

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
6.CHECK FRONT AIRBAG SENSOR
a.

Connect the connector to the airbag sensor assembly.


b.

Temporarily replace the front airbag sensor with a new one.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B161C/9A or B161D/9A is not output. A
DTC B161C/9A or B161D/9A is output. B

HINT:

Codes other than DTCs B161C/9A and B161D/9A may be output at this time, but they are not related to this check.



i.

Reinstall the former front airbag sensor, and connect the connector.



A

END (FRONT AIRBAG SENSOR WAS DEFECTIVE)

B

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.

Disconnect the instrument panel wire connector from the engine room main wire.

U158508E02
4.5,1.073 4.26,1.365 true 6.135,0.927 5.896,1.229 true 6.333,0.906 6.583,1.219 true 1.417,0.281 1.5,0.635 false 4.656,1.083 4.906,1.375 true 4.583,1.281 4.583,1.458 false 1,0.76 1.094,1.115 false 0.531,0.615 0.635,0.771 0.104,0.156 10 false F 0.802,0.833 0.927,0.99 0.125,0.156 10 false E 1.115,0.833 1.24,0.99 0.125,0.156 10 false D 1.281,0.833 1.406,0.99 0.125,0.156 10 false C 1.615,0.823 1.74,0.979 0.125,0.156 10 false B 1.885,0.615 2.01,0.771 0.125,0.156 10 false A 0.188,1.031 0.365,1.208 0.177,0.177 10 false *1 1.771,1.333 1.938,1.51 0.167,0.177 10 false *2 1.271,0.167 1.417,0.323 0.146,0.156 10 false *4 1.021,1.135 1.188,1.292 0.167,0.156 10 false *3 3.115,0.229 3.292,0.427 0.177,0.198 10 false *a 3.313,0.542 3.51,0.729 0.198,0.188 10 false *5 5.448,0.229 5.646,0.375 0.198,0.146 10 false *b 3.26,0.781 3.573,0.938 0.313,0.156 10 false F16 4.115,1.375 4.375,1.531 0.26,0.156 10 false -SL 4.781,1.396 5.104,1.552 0.323,0.156 10 false +SL 5.573,0.542 5.75,0.688 0.177,0.146 10 false *6 5.542,0.771 5.844,0.927 0.302,0.156 10 false AF1 4.51,1.469 4.677,1.625 0.167,0.156 10 false *7 5.729,1.24 6.031,1.396 0.302,0.156 10 false -SL 6.5,1.24 6.823,1.396 0.323,0.156 10 false +SL

Text in Illustration
*1 Front Airbag Sensor *2 Airbag Sensor Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Connector B *6 Connector C
*7 Service Wire - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF1-1 (+SL) - AF1-2 (-SL) Always Below 1 Ω




OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
U158509E02
1.958,2.385 1.646,2.833 true 2.177,2.385 2.531,2.833 true 1.688,0.104 1.875,0.552 false 1.24,0.688 1.427,1.135 false 0.656,0.521 0.76,0.677 0.104,0.156 10 false F 1.01,0.771 1.135,0.927 0.125,0.156 10 false E 1.396,0.771 1.521,0.927 0.125,0.156 10 false D 1.594,0.771 1.719,0.927 0.125,0.156 10 false C 1.99,0.771 2.115,0.927 0.125,0.156 10 false B 2.313,0.542 2.438,0.698 0.125,0.156 10 false A 0.229,1.021 0.375,1.167 0.146,0.146 10 false *1 2.198,1.396 2.365,1.542 0.167,0.146 10 false *2 1.51,0.021 1.677,0.177 0.167,0.156 10 false *4 1.448,1.073 1.604,1.229 0.156,0.156 10 false *3 0.917,1.698 1.115,1.844 0.198,0.146 10 false *a 1.115,2.042 1.292,2.188 0.177,0.146 10 false *5 1.083,2.344 1.385,2.5 0.302,0.156 10 false AF1 1.438,2.854 1.74,3.01 0.302,0.156 10 false -SL 2.448,2.854 2.771,3.01 0.323,0.156 10 false +SL

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF1-1 (+SL) - AF1-2 (-SL) Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Connector C
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U158509E02
1.958,2.385 1.646,2.833 true 2.177,2.385 2.531,2.833 true 1.688,0.104 1.875,0.552 false 1.24,0.688 1.427,1.135 false 0.656,0.521 0.76,0.677 0.104,0.156 10 false F 1.01,0.771 1.135,0.927 0.125,0.156 10 false E 1.396,0.771 1.521,0.927 0.125,0.156 10 false D 1.594,0.771 1.719,0.927 0.125,0.156 10 false C 1.99,0.771 2.115,0.927 0.125,0.156 10 false B 2.313,0.542 2.438,0.698 0.125,0.156 10 false A 0.229,1.021 0.375,1.167 0.146,0.146 10 false *1 2.198,1.396 2.365,1.542 0.167,0.146 10 false *2 1.51,0.021 1.677,0.177 0.167,0.156 10 false *4 1.448,1.073 1.604,1.229 0.156,0.156 10 false *3 0.917,1.698 1.115,1.844 0.198,0.146 10 false *a 1.115,2.042 1.292,2.188 0.177,0.146 10 false *5 1.083,2.344 1.385,2.5 0.302,0.156 10 false AF1 1.438,2.854 1.74,3.01 0.302,0.156 10 false -SL 2.448,2.854 2.771,3.01 0.323,0.156 10 false +SL

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the instrument panel wire connector from the engine room main wire.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AF1-1 (+SL) - Body ground Ignition switch ON Below 1 V
AF1-2 (-SL) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 Front Airbag Sensor
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Connector C
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U158509E02
1.958,2.385 1.646,2.833 true 2.177,2.385 2.531,2.833 true 1.688,0.104 1.875,0.552 false 1.24,0.688 1.427,1.135 false 0.656,0.521 0.76,0.677 0.104,0.156 10 false F 1.01,0.771 1.135,0.927 0.125,0.156 10 false E 1.396,0.771 1.521,0.927 0.125,0.156 10 false D 1.594,0.771 1.719,0.927 0.125,0.156 10 false C 1.99,0.771 2.115,0.927 0.125,0.156 10 false B 2.313,0.542 2.438,0.698 0.125,0.156 10 false A 0.229,1.021 0.375,1.167 0.146,0.146 10 false *1 2.198,1.396 2.365,1.542 0.167,0.146 10 false *2 1.51,0.021 1.677,0.177 0.167,0.156 10 false *4 1.448,1.073 1.604,1.229 0.156,0.156 10 false *3 0.917,1.698 1.115,1.844 0.198,0.146 10 false *a 1.115,2.042 1.292,2.188 0.177,0.146 10 false *5 1.083,2.344 1.385,2.5 0.302,0.156 10 false AF1 1.438,2.854 1.74,3.01 0.302,0.156 10 false -SL 2.448,2.854 2.771,3.01 0.323,0.156 10 false +SL

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF1-1 (+SL) - Body ground Always 1 MΩ or higher
AF1-2 (-SL) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Connector C
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE