Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
RM19S0E _58 Vehicle Interior _051498 HEATING / AIR CONDITIONING _0248350 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1413/13  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor (evaporator temperature sensor) is installed on the evaporator in the air conditioning unit to detect the temperature of the cooled air that has passed through the evaporator and control the air conditioning. It sends appropriate signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes in accordance with the temperature of the cooled air that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor (evaporator temperature sensor) and reads voltage changes as the resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes. This sensor is used for frost prevention.

DTC No. DTC Detection Condition Trouble Area
B1413/13 An open or short in the No. 1 cooler thermistor (evaporator temperature sensor) circuit.
·

No. 1 cooler thermistor (evaporator temperature sensor)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E228240E03
2.26,0.635 2.385,0.802 0.125,0.167 10 false 2 2.26,1.365 2.365,1.521 0.104,0.156 10 false 1 4.74,0.667 4.854,0.833 0.115,0.167 10 false 6 4.729,1.375 4.844,1.542 0.115,0.167 10 false 5 4.979,0.771 5.271,0.938 0.292,0.167 10 false TEA 4.969,1.49 5.281,1.646 0.313,0.156 10 false SGA 0.313,1.802 0.458,1.99 0.146,0.188 10 false A 0.281,1.969 2.292,2.365 2.01,0.396 10 false No. 1 Cooler Thermistor (Evaporator Temperature Sensor) 2.49,2.021 4.677,2.219 2.188,0.198 10 false Air Conditioning Harness Assembly 5.021,1.833 5.208,1.979 0.188,0.146 10 false z4 5,2.01 6.229,2.333 1.229,0.323 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor Evaporator temperature sensor /
Min.: -29.7°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature displayed Open in the circuit: -29.7°C (-21.46°F).
Short in the circuit: 59.55°C (139.19°F).

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.CHECK FOR DTC

B

C

3.INSPECT NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)
3.INSPECT NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)
a.

Inspect the No. 1 cooler thermistor (evaporator temperature sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>INSPECTION).



OK

4.INSPECT AIR CONDITIONING HARNESS ASSEMBLY (NO. 1 COOLER THERMISTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPLACE NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)

4.INSPECT AIR CONDITIONING HARNESS ASSEMBLY (NO. 1 COOLER THERMISTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Remove the air conditioning harness assembly.


b.
U158592E02
1.458,3.844 1.354,4.125 true 1.625,3.833 1.906,4.135 true 0.802,1.344 0.958,1.521 0.156,0.177 10 false A 0.083,0.052 0.25,0.208 0.167,0.156 10 false *1 0.531,3.333 0.698,3.51 0.167,0.177 10 false z4 1.167,4.125 1.479,4.281 0.313,0.156 10 false SGA 1.719,4.135 2.063,4.281 0.344,0.146 10 false TEA

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - z4-6 (TEA) Always Below 1 Ω
A-1 - z4-5 (SGA) Always Below 1 Ω
A-2 - Body ground Always 10 kΩ or higher
A-1 - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Air Conditioning Harness Assembly



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY