Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051498 HEATING / AIR CONDITIONING _0248351 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1412  Ambient Temperature Sensor Circuit  


DESCRIPTION

The thermistor assembly (ambient temperature sensor) is installed in the front part of the cooler condenser assembly to detect the ambient temperature and control the air conditioner. The sensor connected to the air conditioning amplifier assembly detects fluctuations in the ambient temperature. This data is used for controlling the room temperature. The sensor sends a signal to the air conditioning amplifier assembly. The resistance of the thermistor assembly (ambient temperature sensor) changes in accordance with the cooler thermistor temperature (ambient temperature). As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies a voltage (5 V) to the thermistor assembly (ambient temperature sensor) and reads voltage changes as changes in the resistance of the thermistor assembly (ambient temperature sensor).

DTC No. DTC Detection Condition Trouble Area
B1412 An open or short in the thermistor assembly (ambient temperature sensor) circuit.
·

Thermistor assembly (ambient temperature sensor)

·

Harness or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E346166E01
2.438,0.729 2.583,0.917 0.146,0.188 10 false 2 2.438,1.156 2.583,1.344 0.146,0.188 10 false 1 4.938,0.76 5.115,0.948 0.177,0.188 10 false 22 4.979,1.177 5.104,1.375 0.125,0.198 10 false 5 5.25,0.917 5.583,1.115 0.333,0.198 10 false TAM 5.24,1.292 5.573,1.49 0.333,0.198 10 false SG-2 0.708,1.854 0.969,2.042 0.26,0.188 10 false A24 0.719,2.042 2.615,2.406 1.896,0.365 10 false Thermistor Assembly (Ambient Temperature Sensor) 4.677,2.094 4.938,2.281 0.26,0.188 10 false F41 4.677,2.281 6.875,2.479 2.198,0.198 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Ambient Temp Sensor Ambient temperature sensor /
Min.: -23.3°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature is displayed -

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.CHECK FOR DTC

B

C

3.INSPECT THERMISTOR ASSEMBLY (AMBIENT TEMPERATURE SENSOR)
3.INSPECT THERMISTOR ASSEMBLY (AMBIENT TEMPERATURE SENSOR)
a.

Inspect the thermistor assembly (ambient temperature sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY (AMBIENTTEMPERATURE SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPLACE THERMISTOR ASSEMBLY (AMBIENT TEMPERATURE SENSOR)

4.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY (AMBIENTTEMPERATURE SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the A24 thermistor assembly (ambient temperature sensor) connector.


b.

Disconnect the F41 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-2 - F41-22 (TAM) Always Below 1 Ω
A24-1 - F41-5 (SG-2) Always Below 1 Ω
A24-2 - Body ground Always 10 kΩ or higher
A24-1 - Body ground Always 10 kΩ or higher




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR