Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 1NZ-FE, 2NZ-FE) › 2011.08–2017.01
RM19S0E _58 Vehicle Interior _051498 HEATING / AIR CONDITIONING _0248359 COMPRESSOR(for 1NZ-FE, 2NZ-FE) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1NZ-FE, 2NZ-FE)  INSTALLATION  


PROCEDURE

Hide 1.INSPECT COMPRESSOR OIL

a.

Remove the suction seal cap.


b.
I106284E02
2.073,0.854 2.49,0.406 true 2.333,0.979 2.719,0.833 true 2.51,0.302 2.719,0.469 0.208,0.167 10 false *1 2.74,0.719 2.948,0.885 0.208,0.167 10 false *2

Using a screwdriver with its tip wrapped in protective tape, insert the screwdriver through the suction port and set the VST valve (valve inside suction port) to the open position.

Text in Illustration
*1 Protective Tape
*2 VST valve (Valve Inside Suction Port)

NOTICE:

Be sure not to damage the piping contact surfaces with the tip of the screwdriver.



c.
I106285

Lightly shake the compressor with the suction port facing down, and drain the oil (*1).

NOTICE:

Do not allow the pulley to come into contact with the compressor oil.



d.
I106286

With the pulley facing down, rotate the pulley in the direction shown by the arrow 10 times at a rate of approximately once every 2 seconds (*2).

NOTICE:

If the pulley is rotated, refrigerant or oil might splash out. Thus, keep your face away from the compressor port.



e.
I106287

Rotate the pulley once in the direction shown by the arrow while quickly turning the compressor so the pulley is up (*3).


f.

Proceed with the above procedure (*1) and drain the oil (*4).


g.

Drain the oil by repeating the procedures above approximately 5 times (from (*2) to (*4)).

Standard (Amount of Oil to be Removed):
Standard (Amount of Oil to be Removed) Amount of Oil Inside a New Compressor
30 cm3 60 cm3


HINT:

If too much oil has been removed, set the VST valve to the open position through the suction port, and add oil.



Hide 88310 2.INSTALL COMPRESSOR WITH PULLEY ASSEMBLY

a.
I105997E01
0.358,0.705 0.494,0.881 0.136,0.175 10 1 0.784,0.971 0.920,1.146 0.136,0.175 10 4 0.368,1.703 0.504,1.878 0.136,0.175 10 3 0.739,1.898 0.875,2.073 0.136,0.175 10 2

Install the compressor with the 4 bolts.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


b.

Connect the connector.


Hide 88711 3.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the attached vinyl tape from the discharge hose.


b.

Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring onto the discharge hose.


d.

Install the discharge hose onto the compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88704 4.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the attached vinyl tape from the suction hose.


b.

Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring onto the suction hose.


d.

Install the suction hose onto the compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 51441C 5.INSTALL ENGINE UNDER COVER RH (for Plastic Type)

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

Hide 51405A 6.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

Hide 16361A 7.INSTALL FAN AND GENERATOR V BELT