Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING PRESSURE SENSOR
RM19S0E _58 Vehicle Interior _051498 HEATING / AIR CONDITIONING _0248365 AIR CONDITIONING PRESSURE SENSOR G

HEATING / AIR CONDITIONING  AIR CONDITIONING PRESSURE SENSOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 88719A 1.INSPECT AIR CONDITIONER PRESSURE SENSOR (for Manual Air Conditioning System)

a.
U158556E01
0.639,0.983 0.903,1.164 0.264,0.181 10 A23 0.059,0.029 0.229,0.190 0.170,0.161 10 *a 2.112,1.637 2.231,1.796 0.120,0.159 10 + 1.967,1.228 2.141,1.637 false 1.327,1.637 1.438,1.796 0.112,0.159 10 - 1.551,1.228 1.377,1.637 false

Check the wire harness.

Text in Illustration
*a Front view of wire harness connector
(to Air Conditioner Pressure Sensor)

i.

Disconnect the A23 air conditioner pressure sensor connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-1 (-) - Body ground Always Below 1 Ω



iii.

Turn the ignition switch to ON.


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A23-3 (+) - Body ground Ignition switch ON 4.75 to 5.25 V




b.
U158753E01
0.114,0.083 0.307,0.275 0.192,0.192 10 *a 0.51,0.261 0.878,0.429 0.368,0.168 10 PRE 2.474,0.261 2.879,0.435 0.405,0.174 10 SG-2 2.209,0.875 2.411,0.372 false 1.12,0.875 0.918,0.372 false 1.545,0.173 1.801,0.354 0.256,0.181 10 F41

Check the air conditioner pressure sensor.

Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)

i.

Set the manifold gauge.


ii.

Connect the connector to the air conditioner pressure sensor.


iii.

Warm up the engine.


iv.

A/C switch on.


v.

Using a voltmeter, measure the voltage between connector terminals 7 (PRE) and 5 (SG-2) of the air conditioning amplifier assembly.

HINT:

Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.


Standard Voltage:
Tester Connection Refrigerant Pressure Specified Condition
F41-7 (PRE) - F41-5 (SG-2) 0.196 to 3.14 MPa
(2.0 to 32 kgf/cm2, 28 to 455 psi)
0.66 to 4.88 V




Hide 88719A 2.INSPECT AIR CONDITIONER PRESSURE SENSOR (for Automatic Air Conditioning System)

a.
U158556E01
0.639,0.983 0.903,1.164 0.264,0.181 10 A23 0.059,0.029 0.229,0.190 0.170,0.161 10 *a 2.112,1.637 2.231,1.796 0.120,0.159 10 + 1.967,1.228 2.141,1.637 false 1.327,1.637 1.438,1.796 0.112,0.159 10 - 1.551,1.228 1.377,1.637 false

Check the wire harness.

Text in Illustration
*a Front view of wire harness connector
(to Air Conditioner Pressure Sensor)

i.

Disconnect the connector of the air conditioner pressure sensor.


ii.

Using an ohmmeter, measure the resistance of the wire harness side connector.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-1 (-) - Body ground Always Below 1 Ω



iii.

Turn the ignition switch to ON.


iv.

Measure the voltage of the wire harness side connector.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A23-3 (+) - Body ground Ignition switch ON 4.75 to 5.25 V




b.
U158754E01
1.997,0.22 2.437,0.390 0.440,0.170 10 PRE 0.402,0.22 0.842,0.390 0.440,0.170 10 SG-2 1.568,0.894 1.956,0.339 false 1.14,0.908 0.851,0.348 false 0.065,0.052 0.304,0.244 0.239,0.192 10 *a 1.46,0.12 1.716,0.301 0.256,0.181 10 F42

Check the air conditioner pressure sensor.

Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)

i.

Set the manifold gauge.


ii.

Connect the connector to the air conditioner pressure sensor.


iii.

Warm up the engine.


iv.

A/C switch on.


v.

Using a voltmeter, measure the voltage between connector terminals 9 (PRE) and 13 (SG-2) of the air conditioning amplifier assembly.

HINT:

Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.


Standard Voltage:
Tester Connection Refrigerant Pressure Specified Condition
F42-9 (PRE) - F42-13 (SG-2) 0.196 to 3.14 MPa
(2.0 to 32 kgf/cm2, 28 to 455 psi)
0.66 to 4.88 V