Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING PANEL(for Manual Air Conditioning System)
RM19S0E _58 Vehicle Interior _051498 HEATING / AIR CONDITIONING _0248367 AIR CONDITIONING PANEL(for Manual Air Conditioning System) G

HEATING / AIR CONDITIONING  AIR CONDITIONING PANEL(for Manual Air Conditioning System)  INSPECTION  


PROCEDURE

Hide 55901D 1.INSPECT NO. 1 HEATER CONTROL SUB-ASSEMBLY (w/ Heater)

a.

Check the No. 1 heater control sub-assembly resistance.

i.
E218261E01
2.699,0.216 2.897,0.415 0.198,0.198 10 *1 0.247,2.822 0.445,3.020 0.198,0.198 10 *a 1.863,4.294 2.061,4.492 0.198,0.198 10 B 2.104,4.292 2.303,4.490 0.198,0.198 10 E 2.359,4.283 2.557,4.481 0.198,0.198 10 L 0.944,4.296 1.251,4.473 0.307,0.177 10 ILL- 1.367,4.296 1.674,4.473 0.307,0.177 10 ILL+ 1.435,3.957 1.102,4.257 false 1.616,3.954 1.489,4.26 false 1.805,3.947 1.889,4.267 false 1.983,3.944 2.143,4.261 false 2.168,3.947 2.38,4.26 false 1.931,1.404 2.699,0.414 false

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 A/C Switch
*a Component without harness connected
(No. 1 Heater Control Sub-assembly)

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (L) - 3 (E) Always 10 kΩ or higher
2 (L) - 4 (B) A/C switch ON Below 1 Ω
2 (L) - 4 (B) A/C switch OFF 10 kΩ or higher
3 (E) - 4 (B) Always 10 kΩ or higher
5 (ILL+) - 6 (ILL-) Always Below 1 Ω


If the result is not as specified, replace the No. 1 heater control sub-assembly.



b.

Check that the A/C switch indicator.

i.

Connect the positive (+) lead from the battery to terminal 2 (L) and the negative (-) lead to terminal 3 (E).


ii.

Push the A/C switch in and check that the indicator lights up.

OK:

Indicator lights up


If the result is not as specified, replace the heater control sub-assembly.



c.

Check that the heater control illuminates.

i.

Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 5(ILL+)
Battery negative (-) → 6(ILL-)
illuminates


If the result is not as specified, replace the bulb.



Hide 55901D 2.INSPECT NO. 1 HEATER CONTROL SUB-ASSEMBLY (w/o Heater)

a.

Check the No. 1 heater control sub-assembly resistance.

i.
E346206E01
1.5,3.74 1.115,2.792 true 1.854,3.76 2.302,2.823 true 1.448,4.302 1.667,3.885 true 2.51,4.344 2.271,3.875 true 0.115,2.427 0.292,2.635 0.177,0.208 10 false *a 0.875,2.625 1.156,2.813 0.281,0.188 10 false ILL- 2.302,2.656 2.458,2.844 0.156,0.188 10 false B 1.135,4.25 1.417,4.438 0.281,0.188 10 false ILL+ 2.573,4.292 2.708,4.479 0.135,0.188 10 false L

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Component without harness connected
(No. 1 Heater Control Sub-assembly)

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (L) - 4 (B) Always Below 1 Ω


If the result is not as specified, replace the No. 1 heater control sub-assembly.



b.

Check that the heater control illuminates.

i.

Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 5(ILL+)
Battery negative (-) → 6(ILL-)
illuminates


If the result is not as specified, replace the bulb.



Hide 55902E 3.INSPECT NO. 2 HEATER CONTROL SUB-ASSEMBLY

a.

Check the No. 2 heater control sub-assembly resistance.

i.
I106080E01
0.547,0.777 0.691,0.942 0.144,0.165 10 E 0.476,1.321 0.678,1.502 0.202,0.181 10 HI 0.732,1.611 0.980,1.786 0.248,0.175 10 LO 2.294,1.592 2.559,1.762 0.265,0.170 10 M1 2.756,1.459 3.043,1.651 0.286,0.191 10 M2 2.358,0.288 2.739,0.458 0.381,0.170 10 ILL+ 2.756,0.627 3.151,0.807 0.395,0.180 10 ILL- 2.365,0.921 2.731,0.734 false 1.851,0.987 2.326,0.396 false 2.356,1.33 2.722,1.517 false 1.852,1.35 2.251,1.647 false 1.354,1.377 0.955,1.674 false 1.071,1.3 0.664,1.392 false 1.076,0.95 0.668,0.857 false 0.195,2.606 0.409,2.779 0.213,0.173 10 *a 0.795,1.99 1.009,2.163 0.213,0.173 10 *b 1.604,1.774 1.817,1.948 0.213,0.173 10 *c 2.43,1.984 2.643,2.157 0.213,0.173 10 *d 3.051,2.59 3.265,2.764 0.213,0.173 10 *e 0.219,0.073 0.433,0.246 0.213,0.173 10 *f

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a OFF
*b LO
*c M1
*d M2
*e HI
*f Component without harness connected
(No. 2 Heater Control Sub-assembly)

Standard Resistance:
Tester Connection Switch Condition Specified Condition
ALL - 5 (E) 0 (OFF) 10 kΩ or higher
9 (LO) - 5 (E) 1 (LO) Below 1 Ω
9 (LO) - 5 (E) - 7 (M1) 1 (LO) - 2 (M1) Below 1 Ω
9 (LO) - 5 (E) - 7 (M1) 2 (M1) Below 1 Ω
9 (LO) - 5 (E) - 7 (M1) - 6 (M2) 2 (M1) - 3 (M2) Below 1 Ω
9 (LO) - 5 (E) - 6 (M2) 3 (M2) Below 1 Ω
9 (LO) - 5 (E) - 10 (HI) - 6 (M2) 3 (M2) - 4(HI) Below 1 Ω
9 (LO) - 5 (E) - 10 (HI) 4 (HI) Below 1 Ω


If the result is not as specified, replace the No. 2 heater control sub-assembly.



b.

Check that the heater control illuminates.

i.

Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2(ILL+)
Battery negative (-) → 1(ILL-)
illuminates


If the result is not as specified, replace the bulb.



Hide 55903A 4.INSPECT NO. 3 HEATER CONTROL SUB-ASSEMBLY (w/ Heater)

a.

Check the No. 3 heater control sub-assembly resistance.

i.
E218262E01
2.864,0.294 3.069,0.470 0.206,0.176 10 *1 2.864,2.821 3.069,2.997 0.206,0.176 10 *a 0.383,2.97 0.588,3.145 0.206,0.176 10 *b 0.532,4.362 0.771,4.523 0.239,0.161 10 SG 1.976,2.97 2.215,3.131 0.239,0.161 10 IG 2.915,4.11 3.057,4.271 0.142,0.161 10 E 0.933,4.371 1.607,4.531 0.674,0.161 10 MAX-HOT 2.188,4.376 2.640,4.537 0.452,0.161 10 RrDEF 1.821,4.376 2.120,4.537 0.299,0.161 10 ILL- 1.059,2.961 1.358,3.122 0.299,0.161 10 V/B 1.476,2.963 1.775,3.124 0.299,0.161 10 ILL+ 1.068,4.021 0.753,4.329 false 1.479,4.021 1.383,4.339 false 1.837,4.017 1.924,4.357 false 2.211,4.021 2.421,4.345 false 2.443,3.993 2.891,4.184 false 2.075,3.162 2.038,3.841 false 1.655,3.141 1.66,3.851 false 1.182,3.139 1.306,3.851 false 2.864,0.443 1.912,1.463 false 2.166,2.113 2.834,2.826 false

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 Rr Defogger Switch
*a MAX HOT
*b Component without harness connected
(No. 3 Heater Control Sub-assembly)

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (Rr DEF) - 1(E) Rear window defogger switch on Below 1 Ω
Rear window defogger switch off 10 kΩ or higher
3 (IG) - 6 (MAX-HOT) MAX HOT Below 1 Ω
Except MAX HOT 10 kΩ or higher
7 (V/B) - 8 (SG) Always Below 1 Ω


If the result is not as specified, replace the No. 3 heater control sub-assembly.


ii.

Measure the resistance according to the value(s) in the table below (for Cold Area Specification Vehicles).

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (IG) - 6 (MAX-HOT) MAX HOT Below 1 Ω
Except MAX HOT 10 kΩ or higher


If the result is not as specified, replace the No. 3 heater control sub-assembly.



b.

Check that the rear window defogger indicator.

i.

Connect the positive (+) lead from the battery to terminal 3 (IG) and the negative (-) lead to terminal 1 (E).


ii.

Push the rear window defogger switch in and check that the indicator lights up.

OK:

Indicator lights up


If the result is not as specified, replace the No. 3 heater control sub-assembly.




c.

Check that the heater control illuminates.

i.

Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 5(ILL+)
Battery negative (-) → 4(ILL-)
illuminates


If the result is not as specified, replace the bulb.



Hide 55903A 5.INSPECT NO. 3 HEATER CONTROL SUB-ASSEMBLY (w/o Heater)

a.

Check the No. 3 heater control sub-assembly resistance.

i.

Using an ohmmeter, measure the resistance variation between connector terminals 7 (A/C) and 8 (SG) when the dial is turned as shown in the illustration.

E346207E01
1.594,3.323 1.021,2.823 false 1.76,3.313 2.26,2.698 false 4.375,2.656 4.521,2.844 0.146,0.188 10 false 0° 3.073,2.344 3.406,2.51 0.333,0.167 10 false 270° 1.333,2.479 1.5,2.667 0.167,0.188 10 false *a 0.729,2.719 0.958,2.917 0.229,0.198 10 false SG 2.323,2.563 2.583,2.76 0.26,0.198 10 false A/C 0.938,2.354 1.083,2.542 0.146,0.188 10 false 0° 4.198,2.469 4.313,2.625 0.115,0.156 10 false 0 4.198,1.479 4.313,1.635 0.115,0.156 10 false 3 4.615,2.667 4.844,2.844 0.229,0.177 10 false 10° 5.281,2.667 5.583,2.844 0.302,0.177 10 false 135° 6.01,2.646 6.313,2.823 0.302,0.177 10 false 260° 6.323,2.646 6.625,2.823 0.302,0.177 10 false 270° 5.844,1.896 6.75,2.094 0.906,0.198 10 false Rotation Angle 4.313,1.104 4.729,1.281 0.417,0.177 10 false (kΩ)∞ 4.292,0.813 5,0.99 0.708,0.177 10 false Resistance

Text in Illustration
*a Component without harness connected
(No. 3 Heater Control Sub-assembly)

OK:

Varies as shown in the illustration


If the result is not as specified, replace the No. 3 heater control sub-assembly.



b.
E346208E01
1.906,1.229 2.698,0.292 false 2.01,3.781 2.542,2.896 false 1.385,4.302 1.625,3.917 false 2.073,4.302 1.854,3.927 false 2.875,4.115 2.417,3.896 false 2.604,2.792 2.875,2.958 0.271,0.167 10 false IG+ 0.656,2.833 0.844,3 0.188,0.167 10 false *a 1.208,4.323 1.521,4.49 0.313,0.167 10 false ILL+ 2.729,0.198 2.917,0.365 0.188,0.167 10 false *1 2.021,4.333 2.333,4.5 0.313,0.167 10 false ILL- 2.927,4.063 3.083,4.25 0.156,0.188 10 false E

Check that the rear window defogger indicator.

Text in Illustration
*1 Rr Window Defogger Switch
*a Component without harness connected
(No. 3 Heater Control Sub-assembly)

i.

Connect the positive (+) lead from the battery to terminal 3 (IG+) and the negative (-) lead to terminal 1 (E).


ii.

Push the rear window defogger switch in and check that the indicator lights up.

OK:

Indicator lights up


If the result is not as specified, replace the No. 3 heater control sub-assembly.




c.

Check that the heater control illuminates.

i.

Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 5(ILL+)
Battery negative (-) → 4(ILL-)
illuminates


If the result is not as specified, replace the bulb.