Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING(for 3 Door)
RM19S0E _58 Vehicle Interior _051500 INTERIOR PANELS / TRIM _0248373 ROOF HEADLINING(for 3 Door) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for 3 Door)  REASSEMBLY  


PROCEDURE

Hide 82171 1.INSTALL NO. 1 ROOF WIRE

a.

Align the No. 1 roof wire positioning tape with the markings of the roof headlining.

B284338E01
1.323,0.425 1.526,0.584 0.203,0.159 10 *1 1.943,1.852 2.147,2.019 0.203,0.167 10 *2 2.381,2.226 2.584,2.394 0.203,0.167 10 *3 1.489,0.547 1.754,0.75 false 2.04,1.826 2.078,1.664 false 2.215,2.104 2.381,2.226 false

Text in Illustration
*1 Tape *2 Positioning Tape
*3 Marking - -


b.

Install the No. 1 roof wire onto the roof headlining with 7 new pieces of tape.

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.




Hide 66414A 2.INSTALL REAR SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

a.
B284336

Align the markings on the roof headlining assembly with the rear side rail spacer and install the rail spacer using hot melt glue.

Text in Illustration
V100155

Adhesive Portion


Hide 66424 3.INSTALL REAR SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)

HINT:

Use the same procedure as for the RH side.


Hide 66414A 4.INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B272637

Align the markings on the roof headlining assembly with the rear side rail spacer and install the rail spacer using hot melt glue.

Text in Illustration
V100155

Adhesive Portion


Hide 66424 5.INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure as for the RH side.


Hide 63343B 6.INSTALL REAR ROOF SILENCER PAD

a.
B290388

Align the markings on the roof headlining assembly with the 4 rear roof silencer pads and install the silencer pads using hot melt glue.


Hide 63345 7.INSTALL NO. 5 ROOF SILENCER PAD

a.
B284334

Align the markings on the roof headlining assembly with the 2 No. 5 roof silencer pads and install the silencer pads using hot melt glue.


Hide 63341G 8.INSTALL ROOF SILENCER PAD

a.

Align the markings on the roof headlining assembly with the 4 roof silencer pads and install the silencer pads using hot melt glue.

B284339E01
5.413,0.402 5.583,0.570 0.170,0.168 10 *a 6.088,1.05 6.258,1.218 0.170,0.168 10 *a 6.19,1.396 6.360,1.563 0.170,0.168 10 *1 6.175,1.451 5.964,1.347 false 6.554,0.339 6.724,0.507 0.170,0.168 10 *2 6.554,0.449 6.378,0.513 false

Text in Illustration
*1 Roof Silencer Pad *2 Marking
*a 25.0 mm (0.984 in.) - -


Hide 86101J 9.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY