58410B
1.REMOVE DECK BOARD ASSEMBLY
Remove the deck board.
64771G
2.REMOVE SPARE WHEEL COVER
Remove the spare wheel cover.
3.REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
4.REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
5.REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)
67913
6.REMOVE FRONT DOOR SCUFF PLATE RH
Disengage the 8 claws and remove the front door scuff plate.
67914
7.REMOVE FRONT DOOR SCUFF PLATE LH
Use the same procedure as for the RH side.
62111C
8.REMOVE COWL SIDE TRIM BOARD RH
Remove the clip.
Disengage the clip and remove the cowl side trim board.
62112
9.REMOVE COWL SIDE TRIM BOARD LH
Use the same procedure as for the RH side.
62311B
10.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Remove the front door opening trim weatherstrip.
62312B
11.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Use the same procedure as for the RH side.
67917A
12.REMOVE REAR DOOR SCUFF PLATE RH
Disengage the 5 claws and guide and remove the rear door scuff plate.
67918A
13.REMOVE REAR DOOR SCUFF PLATE LH
Use the same procedure as for the RH side.
62331A
14.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Remove the rear door opening trim weatherstrip.
62332A
15.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Use the same procedure as for the RH side.
73210
16.SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH
Disengage the 2 claws and remove the anchor cover.
Remove the bolt and separate the front seat outer belt.
73220
17.SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH
Use the same procedure as for the RH side.
62413A
18.REMOVE CENTER PILLAR LOWER GARNISH RH
Disengage the 2 clips and the 2 claws.
Disengage the 2 guides and remove the center pillar lower garnish.
62414A
19.REMOVE CENTER PILLAR LOWER GARNISH LH
Use the same procedure as for the RH side.
62411B
20.REMOVE CENTER PILLAR UPPER GARNISH RH
Remove the 2 screws and disengage the clip.
Pass the front seat outer belt through the slit in the center pillar upper garnish and remove the center pillar upper garnish.
62412B
21.REMOVE CENTER PILLAR UPPER GARNISH LH
Use the same procedure as for the RH side.
62211
22.REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)
Disengage the front pillar garnish clip and the clip.
| *1 | Front Pillar Garnish Clip |
The front pillar garnish clip should remain between the front pillar garnish and the pillar.
Using needle nose pliers, turn the front pillar garnish clip 90° and disengage it from the front pillar garnish.
| *1 | Protective Tape |
As a pillar garnish clip is reusable, do not remove it from the pillar as long as it is not damaged.
Replace the front pillar garnish clips with new ones if they are removed from the vehicle.
Tape the needle-nosed pliers tip before use.
Disengage the 2 guides and remove the front pillar garnish.
for 6 speakers:
Disconnect the connector.
Protect the curtain shield airbag assembly.
| *1 | Adhesive Tape |
| *2 | Protective Cover |
| *3 | Curtain Shield Airbag Assembly |
Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
62212
23.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)
Use the same procedure as for the RH side.
62211
24.REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)
Disengage the 2 clips and the 2 guides and remove the front pillar garnish.
for 6 speakers:
Disconnect the connector.
62212
25.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)
Use the same procedure as for the RH side.
81250
26.REMOVE NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)
09113
27.REMOVE JACK HANDLE
58387B
28.REMOVE REAR FLOOR FINISH PLATE
Disengage the 4 claws and 4 guides and remove the rear floor finish plate.
73360
29.SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
Remove the bolt.
Disengage the 2 claws and separate the rear seat 3 point type outer belt.
73370
30.SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
Use the same procedure as for the RH side.
64730B
31.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Remove the 3 screws.
Disengage the 4 claws and the guide.
Disengage the 3 clips and remove the deck trim side panel.
64740C
32.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Use the same procedure as for the RH side.
62471A
33.REMOVE ROOF SIDE INNER GARNISH RH
Disengage the 4 clips.
Pass the rear seat 3 point type outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
62472A
34.REMOVE ROOF SIDE INNER GARNISH LH
Use the same procedure as for the RH side.
74310
35.REMOVE VISOR ASSEMBLY RH
Remove the visor shaft from the visor holder.
Remove the 2 screws and the visor.
74320
36.REMOVE VISOR ASSEMBLY LH
Use the same procedure as for the RH side.
74348
37.REMOVE VISOR HOLDER
Turn the visor holder clockwise 45° and disengage the 2 claws to remove the visor holder.
Use the same procedure for the LH side and RH side.
74610S
38.REMOVE ASSIST GRIP ASSEMBLY
Use the same procedure to remove all assist grips.
Using a moulding remover, disengage the 4 claws and remove the 2 assist grip covers.
Disengage the 2 clips and remove the assist grip.
63339A
39.REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/ Cover)
Use the same procedure to remove all roof headlining service hole covers.
Using a clip remover, remove the 2 roof headlining service hole covers.
81260A
40.REMOVE MAP LIGHT ASSEMBLY
73350C
41.SEPARATE REAR CENTER SEAT OUTER BELT ASSEMBLY
Disengage the 2 claws and open the slip joint cover.
Remove the bolt and separate the rear center seat outer belt.
42.REMOVE ROOF HEADLINING ASSEMBLY
| *a | Front Pillar RH Side | *b | Front Pillar LH Side |
| *c | Rear Pillar RH Side | - | - |
for front pillar RH side:
Disconnect the connector.
Using a clip remover, disengage the 4 clamps.
for front pillar LH side:
Disconnect the connector.
Using a clip remover, disengage the 4 clamps.
for rear pillar RH side:
Disconnect the connector.
Using a clip remover, disengage the 3 clamps.
Disengage the 2 claws.
Using a clip remover, remove the 3 clips.
Disengage the 2 hooks.
Remove the roof headlining from the vehicle through the back door as shown in the illustration.
Do not damage the roof headlining assembly or body interior.