Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW MASTER SWITCH
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248379 POWER WINDOW MASTER SWITCH G

WINDOW / GLASS  POWER WINDOW MASTER SWITCH  INSPECTION  


PROCEDURE

Hide 84820 1.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Rear Power Window)

a.
B302422E42
1.25,1.677 0.729,1.063 true 1.563,1.656 0.604,0.656 true 1.719,1.667 1.042,0.26 true 1.875,1.646 2.646,0.51 true 2.344,1.656 2.646,0.979 true 1.104,2 0.708,2.542 true 1.406,2 0.958,2.771 true 1.573,2 1.406,2.906 true 2.354,2.01 2.719,2.542 true 2.042,2 2.458,2.771 true 1.875,2 2.042,2.906 true 0.531,0.927 0.76,1.094 0.229,0.167 10 false UP 0.094,0.063 0.281,0.229 0.188,0.167 10 false *a 0.896,2.771 1.021,2.938 0.125,0.167 10 false U 2.417,2.771 2.542,2.938 0.125,0.167 10 false U 1.344,2.906 1.469,3.073 0.125,0.167 10 false D 2,2.906 2.125,3.073 0.125,0.167 10 false D 0.656,2.542 0.781,2.708 0.125,0.167 10 false D 2.698,0.865 3.146,1.031 0.448,0.167 10 false GND 2.667,2.542 2.802,2.708 0.135,0.167 10 false U 2.698,0.385 3.229,0.552 0.531,0.167 10 false AUTO 0.677,0.104 1.146,0.271 0.469,0.167 10 false DOWN 0.469,0.542 0.615,0.708 0.146,0.167 10 false B

Check the switch function (for LHD).

Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

i.

Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Driver Side Switch
Tester Connection Condition Specified Condition
4 (AUTO) - 1 (GND) AUTO UP Below 1 Ω
8 (UP) - 1 (GND) AUTO UP Below 1 Ω
8 (UP) - 1 (GND) MANUAL UP Below 1 Ω
5 (DOWN) - 1 (GND) MANUAL DOWN Below 1 Ω
4 (AUTO) - 1 (GND) AUTO DOWN Below 1 Ω
5 (DOWN) - 1 (GND) AUTO DOWN Below 1 Ω


Standard Resistance:
Front Passenger Side Switch
Tester Connection Condition Specified Condition
6 (B) - 16 (U) UP Below 1 Ω
1 (GND) - 15 (D) UP Below 1 Ω
1 (GND) - 16 (U) OFF Below 1 Ω
1 (GND) - 15 (D) OFF Below 1 Ω
1 (GND) - 16 (U) DOWN Below 1 Ω
6 (B) - 15 (D) DOWN Below 1 Ω


Standard Resistance:
Rear RH Side Switch
Tester Connection Condition Specified Condition
6 (B) - 10 (U) UP Below 1 Ω
1 (GND) - 18 (D) UP Below 1 Ω
1 (GND) - 18 (D) OFF Below 1 Ω
1 (GND) - 10 (U) OFF Below 1 Ω
6 (B) - 18 (D) DOWN Below 1 Ω
1 (GND) - 10 (U) DOWN Below 1 Ω


Standard Resistance:
Rear LH Side Switch
Tester Connection Condition Specified Condition
6 (B) - 12 (U) UP Below 1 Ω
1 (GND) - 13 (D) UP Below 1 Ω
1 (GND) - 13 (D) OFF Below 1 Ω
1 (GND) - 12 (U) OFF Below 1 Ω
6 (B) - 13 (D) DOWN Below 1 Ω
1 (GND) - 12 (U) DOWN Below 1 Ω


If the result is not as specified, replace the power window regulator master switch assembly.



b.
B302422E43
1.104,1.646 0.667,1.115 true 1.563,1.646 0.688,0.667 true 1.719,1.677 1.156,0.26 true 2.333,0.552 1.875,1.656 true 2.333,1.656 2.729,1.052 true 2.344,1.99 2.719,2.49 true 2.042,2 2.448,2.771 true 1.875,2 2.094,3.042 true 1.104,1.99 0.792,2.51 true 1.417,1.99 1.01,2.771 true 1.573,2 1.323,3.042 true 0.375,0.979 0.719,1.146 0.344,0.167 10 false GND 0.104,0.042 0.292,0.208 0.188,0.167 10 false *a 0.948,2.771 1.073,2.938 0.125,0.167 10 false U 2.458,2.792 2.583,2.958 0.125,0.167 10 false U 1.25,3.042 1.375,3.208 0.125,0.167 10 false D 2.052,3.042 2.177,3.208 0.125,0.167 10 false D 2.74,2.51 2.865,2.677 0.125,0.167 10 false D 0.719,2.51 0.844,2.677 0.125,0.167 10 false U 2.771,0.927 3.042,1.094 0.271,0.167 10 false UP 2.375,0.417 2.844,0.583 0.469,0.167 10 false AUTO 0.792,0.104 1.26,0.271 0.469,0.167 10 false DOWN 0.531,0.552 0.677,0.719 0.146,0.167 10 false B

Check the switch function (for RHD).

Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

i.

Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Driver Side Switch
Tester Connection Condition Specified Condition
4 (AUTO) - 9 (GND) AUTO UP Below 1 Ω
1 (UP) - 9 (GND) AUTO UP Below 1 Ω
1 (UP) - 9 (GND) MANUAL UP Below 1 Ω
5 (DOWN) - 9 (GND) MANUAL DOWN Below 1 Ω
4 (AUTO) - 9 (GND) AUTO DOWN Below 1 Ω
5 (DOWN) - 9 (GND) AUTO DOWN Below 1 Ω


Standard Resistance:
Front Passenger Side Switch
Tester Connection Condition Specified Condition
6 (B) - 12 (U) UP Below 1 Ω
9 (GND) - 13 (D) UP Below 1 Ω
9 (GND) - 12 (U) OFF Below 1 Ω
9 (GND) - 13 (D) OFF Below 1 Ω
9 (GND) - 12 (U) DOWN Below 1 Ω
6 (B) - 13 (D) DOWN Below 1 Ω


Standard Resistance:
Rear RH Side Switch
Tester Connection Condition Specified Condition
6 (B) - 16 (U) UP Below 1 Ω
9 (GND) - 15 (D) UP Below 1 Ω
9 (GND) - 15 (D) OFF Below 1 Ω
9 (GND) - 16 (U) OFF Below 1 Ω
6 (B) - 15 (D) DOWN Below 1 Ω
9 (GND) - 16 (U) DOWN Below 1 Ω


Standard Resistance:
Rear LH Side Switch
Tester Connection Condition Specified Condition
6 (B) - 18 (U) UP Below 1 Ω
9 (GND) - 10 (D) UP Below 1 Ω
9 (GND) - 10 (D) OFF Below 1 Ω
9 (GND) - 18 (U) OFF Below 1 Ω
6 (B) - 10 (D) DOWN Below 1 Ω
9 (GND) - 18 (U) DOWN Below 1 Ω


If the result is not as specified, replace the power window regulator master switch assembly.



c.
B302422E29
2.753,0.733 3.099,0.904 0.346,0.171 10 GND 1.238,0.733 1.602,0.904 0.364,0.171 10 LED 0.28,0.29 0.468,0.461 0.188,0.171 10 *a 2.036,1.668 1.609,0.821 false 2.344,1.663 2.731,0.816 false

Check that the LED illuminates (for LHD).

Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

i.

Apply auxiliary battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (LED)
Auxiliary battery negative (-) → Terminal 1 (GND)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



d.
B302422E28
0.373,0.733 0.745,0.904 0.372,0.171 10 GND 2.357,0.733 2.771,0.904 0.414,0.171 10 LED 0.125,0.101 0.313,0.272 0.188,0.171 10 *a 1.1,1.663 0.784,0.819 false 2.032,1.663 2.335,0.825 false

Check that the LED illuminates (for RHD).

Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

i.

Apply auxiliary battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (LED)
Auxiliary battery negative (-) → Terminal 9 (GND)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



e.
B364773E07
0.588,0.542 0.820,0.710 0.232,0.168 10 UP 2.767,0.542 3.121,0.716 0.354,0.174 10 GND 2.561,0.168 3.017,0.385 0.456,0.217 10 AUTO 0.502,0.168 0.975,0.330 0.473,0.162 10 DOWN 1.253,1.444 0.853,0.627 false 1.721,1.439 1.083,0.258 false 1.876,1.424 2.527,0.262 false 2.342,1.42 2.741,0.629 false 0.096,0.085 0.329,0.253 0.232,0.168 10 *a

Check the switch function (for LHD).

Text in Illustration
*a Component with harness connected
(Power Window Regulator Master Switch Assembly)

i.

Reconnect the power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
8 (UP) - 1 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
8 (UP) - 1 (GND) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
8 (UP) - 1 (GND) Ignition switch ON, driver door power window regulator switch up (Manual operation) Below 1 V
4 (AUTO) - 1 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
4 (AUTO) - 1 (GND) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
4 (AUTO) - 1 (GND) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
5 (DOWN) - 1 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
5 (DOWN) - 1 (GND) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
5 (DOWN) - 1 (GND) Ignition switch ON, driver door power window regulator switch down (Manual operation) Below 1 V


If the result is not as specified, replace the power window regulator master switch assembly.



f.
B364773E06
0.285,0.757 0.710,0.917 0.425,0.161 10 GND 2.853,0.705 3.132,0.888 0.279,0.183 10 UP 0.377,0.389 0.867,0.553 0.489,0.164 10 DOWN 2.647,0.338 3.103,0.518 0.456,0.180 10 AUTO 1.113,1.424 0.7,0.844 false 1.721,1.442 0.954,0.473 false 1.878,1.427 2.617,0.43 false 2.339,1.421 2.834,0.788 false 0.113,0.098 0.539,0.259 0.425,0.161 10 *a

Check the switch function (for RHD).

Text in Illustration
*a Component with harness connected
(Power Window Regulator Master Switch Assembly)

i.

Reconnect the power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 (UP) - 9 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
1 (UP) - 9 (GND) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
1 (UP) - 9 (GND) Ignition switch ON, driver door power window regulator switch up (Manual operation) Below 1 V
4 (AUTO) - 9 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
4 (AUTO) - 9 (GND) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
4 (AUTO) - 9 (GND) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
5 (DOWN) - 9 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
5 (DOWN) - 9 (GND) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
5 (DOWN) - 9 (GND) Ignition switch ON, driver door power window regulator switch down (Manual operation) Below 1 V


If the result is not as specified, replace the power window regulator master switch assembly.



Hide 84820 2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/o Rear Power Window)

a.
B302422E27
2.41,2.541 2.883,2.712 0.473,0.171 10 DOWN 2.083,2.743 2.213,2.914 0.130,0.171 10 U 1.169,2.743 1.299,2.914 0.130,0.171 10 D 1.401,1.996 1.233,2.743 false 1.599,2.846 1.729,3.017 0.130,0.171 10 B 0.653,2.558 0.895,2.729 0.242,0.171 10 UP 2.675,0.67 3.134,0.840 0.460,0.171 10 AUTO 0.43,0.67 0.783,0.840 0.353,0.171 10 GND 0.136,0.087 0.358,0.258 0.221,0.171 10 *a 1.406,1.623 0.856,0.751 false 2.344,1.62 2.629,0.759 false 1.104,1.998 0.786,2.541 false 1.573,1.996 1.663,2.846 false 2.342,1.996 2.649,2.541 false 2.041,1.996 2.142,2.743 false

Check the switch function (for LHD).

Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

i.

Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Driver Side Switch
Tester Connection Condition Specified Condition
1 (AUTO) - 7 (GND) AUTO UP Below 1 Ω
18 (UP) - 7 (GND) AUTO UP Below 1 Ω
18 (UP) - 7 (GND) MANUAL UP Below 1 Ω
10 (DOWN) - 7 (GND) MANUAL DOWN Below 1 Ω
1 (AUTO) - 7 (GND) AUTO DOWN Below 1 Ω
10 (DOWN) - 7 (GND) AUTO DOWN Below 1 Ω


Standard Resistance:
Front Passenger Side Switch
Tester Connection Condition Specified Condition
15 (B) - 12 (U) UP Below 1 Ω
7 (GND) - 16 (D) UP Below 1 Ω
7 (GND) - 12 (U) OFF Below 1 Ω
7 (GND) - 16 (D) OFF Below 1 Ω
7 (GND) - 12 (U) DOWN Below 1 Ω
15 (B) - 16 (D) DOWN Below 1 Ω


If the result is not as specified, replace the power window regulator master switch assembly.



b.
B302422E44
1.104,1.656 0.76,0.927 true 1.563,1.646 1.76,0.698 true 1.406,1.667 1.125,0.563 true 2.333,1.99 2.74,2.542 false 2.042,2 2.24,2.813 false 1.573,1.99 1.271,2.813 false 1.104,2 0.792,2.542 false 2.688,2.542 2.844,2.708 0.156,0.167 10 false D 2.188,2.813 2.313,2.979 0.125,0.167 10 false U 1.219,2.833 1.344,3 0.125,0.167 10 false B 0.521,2.573 0.979,2.74 0.458,0.167 10 false AUTO 0.854,0.385 1.219,0.552 0.365,0.167 10 false GND 0.115,0.083 0.333,0.25 0.219,0.167 10 false *a 1.688,0.51 2.188,0.677 0.5,0.167 10 false DOWN 0.594,0.781 0.833,0.948 0.24,0.167 10 false UP

Check the switch function (for RHD).

Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

i.

Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Driver Side Switch
Tester Connection Condition Specified Condition
18 (AUTO) - 7 (GND) AUTO UP Below 1 Ω
9 (UP) - 7 (GND) AUTO UP Below 1 Ω
9 (UP) - 7 (GND) MANUAL UP Below 1 Ω
6 (DOWN) - 7 (GND) MANUAL DOWN Below 1 Ω
18 (AUTO) - 7 (GND) AUTO DOWN Below 1 Ω
6 (DOWN) - 7 (GND) AUTO DOWN Below 1 Ω


Standard Resistance:
Front Passenger Side Switch
Tester Connection Condition Specified Condition
15 (B) - 12 (U) UP Below 1 Ω
7 (GND) - 10 (D) UP Below 1 Ω
7 (GND) - 12 (U) OFF Below 1 Ω
7 (GND) - 10 (D) OFF Below 1 Ω
7 (GND) - 12 (U) DOWN Below 1 Ω
15 (B) - 10 (D) DOWN Below 1 Ω


If the result is not as specified, replace the power window regulator master switch assembly.



c.
B302422E25
0.688,0.733 1.050,0.904 0.362,0.171 10 GND 0.14,0.109 0.362,0.280 0.221,0.171 10 *a 2.117,0.733 2.444,0.904 0.327,0.171 10 LED 1.406,1.663 1.106,0.824 false 1.567,1.663 2.091,0.818 false

Check that the LED illuminates (for LHD).

Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

i.

Apply auxiliary battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 6 (LED)
Auxiliary battery negative (-) → Terminal 7 (GND)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



d.
B302422E24
0.662,0.768 1.034,0.939 0.372,0.171 10 GND 0.097,0.065 0.318,0.235 0.221,0.171 10 *a 0.813,2.804 1.140,2.975 0.327,0.171 10 LED 1.083,0.855 1.407,1.627 false 1.414,1.998 0.96,2.779 false

Check that the LED illuminates (for RHD).

Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

i.

Apply auxiliary battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 16 (LED)
Auxiliary battery negative (-) → Terminal 7 (GND)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



e.
B364773E13
1.406,1.417 0.885,0.604 true 2.344,1.427 2.635,0.625 true 1.104,1.76 0.802,2.365 true 2.354,1.771 2.552,2.375 true 0.667,2.385 0.927,2.563 0.26,0.177 10 false UP 0.615,0.427 0.979,0.719 0.365,0.292 10 false GND 2.563,0.438 3.021,0.656 0.458,0.219 10 false AUTO 2.313,2.385 2.823,2.573 0.51,0.188 10 false DOWN 0.146,0.063 0.604,0.281 0.458,0.219 10 false *a

Check the switch function (for LHD).

Text in Illustration
*a Component with harness connected
(Power Window Regulator Master Switch Assembly)

i.

Reconnect the power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
18 (UP) - 7 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
18 (UP) - 7 (GND) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
18 (UP) - 7 (GND) Ignition switch ON, driver door power window regulator switch up (Manual operation) Below 1 V
1 (AUTO) - 7 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
1 (AUTO) - 7 (GND) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
1 (AUTO) - 7 (GND) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
10 (DOWN) - 7 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
10 (DOWN) - 7 (GND) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
10 (DOWN) - 7 (GND) Ignition switch ON, driver door power window regulator switch down (Manual operation) Below 1 V


If the result is not as specified, replace the power window regulator master switch assembly.



f.
B364773E04
0.665,0.381 1.015,0.543 0.350,0.162 10 GND 1.083,0.488 1.407,1.397 false 0.476,0.707 0.730,0.870 0.254,0.162 10 UP 2.006,0.518 2.576,0.681 0.570,0.162 10 DOWN 0.739,0.814 1.115,1.397 false 1.104,1.768 0.65,2.549 false 1.964,0.616 1.561,1.397 false 0.416,2.568 0.853,2.730 0.437,0.162 10 AUTO 0.114,0.088 0.312,0.250 0.198,0.162 10 *a

Check the switch function (for RHD).

Text in Illustration
*a Component with harness connected
(Power Window Regulator Master Switch Assembly)

i.

Reconnect the power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
9 (UP) - 7 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
9 (UP) - 7 (GND) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
9 (UP) - 7 (GND) Ignition switch ON, driver door power window regulator switch up (Manual operation) Below 1 V
18 (AUTO) - 7 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
18 (AUTO) - 7 (GND) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
18 (AUTO) - 7 (GND) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
6 (DOWN) - 7 (GND) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
6 (DOWN) - 7 (GND) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
6 (DOWN) - 7 (GND) Ignition switch ON, driver door power window regulator switch down (Manual operation) Below 1 V


If the result is not as specified, replace the power window regulator master switch assembly.