Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door)
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248382 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 85710E 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)

NOTICE:
·

Do not apply voltage to any terminals except terminals 1 and 2, to avoid damaging the pulse sensor inside the motor.

·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



a.

Apply battery voltage to the motor connector according to the table below.

B172246E04
3.213,1.122 3.501,1.403 0.288,0.281 10 *c 0.195,0.134 0.381,0.297 0.185,0.163 10 *A 4.156,0.134 4.349,0.283 0.193,0.150 10 *B 4.917,1.437 5.081,1.607 0.164,0.170 10 *b 1.705,2.042 2.395,2.211 0.691,0.170 10 *b 2.09,1.632 3.232,1.788 1.142,0.156 10 *a 5.304,2.026 5.498,2.182 0.194,0.156 10 *a 6.329,2.454 6.508,2.624 0.179,0.170 10 *1 0.803,2.469 0.968,2.639 0.165,0.170 10 *1 1.365,1.901 0.948,2.458 false 5.805,1.901 6.298,2.446 false

Text in Illustration
*A for LHD *B for RHD
*1 Motor Gear - -
*a Counterclockwise *b Clockwise
*c Component without harness connected
(Power Window Regulator Motor (Driver Side))
- -

OK:
Switch Condition Measurement Condition Specified Condition
Manual Operation Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (E), 7 (DWN1)
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (E), 10 (UP1)
Motor gear rotates clockwise
Auto Operation Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (E), 4 (AUTO), 7 (DWN1)
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (E), 4 (AUTO), 10 (UP1)
Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly.


Hide 85720D 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side)

a.

Apply battery voltage to the motor connector according to the table below.

B272442E02
0.744,1.901 0.947,2.099 0.203,0.198 10 *a 3.048,1.119 3.251,1.317 0.203,0.198 10 *c 2.687,2.248 2.890,2.446 0.203,0.198 10 *1 4.359,2.235 4.562,2.433 0.203,0.198 10 *1 6.402,1.353 6.605,1.551 0.203,0.198 10 *a 6.269,2.004 6.472,2.202 0.203,0.198 10 *b 0.588,1.219 0.791,1.417 0.203,0.198 10 *b 0.2,0.106 0.423,0.311 0.223,0.205 10 *A 4.22,0.106 4.443,0.311 0.223,0.205 10 *B 1.879,1.537 2.616,2.273 false 5.258,1.531 4.521,2.268 false

Text in Illustration
*A for LHD *B for RHD
*1 Motor Gear - -
*a Counterclockwise *b Clockwise
*c Component without harness connected
(Power Window Regulator Motor (Front Passenger Side))
- -

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates clockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly.