Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2014.07–2017.01
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248384 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


PROCEDURE

Hide 56111 1.CLEAN WINDSHIELD GLASS

a.
B106929

Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



b.

Clean the outer edge of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.




Hide 56116C 2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

Using a brush or sponge, coat the application area of the No. 2 windshield glass stoppers with Primer G.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



b.

Install 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.

B272662E01
0.204,0.174 0.395,0.340 0.191,0.166 10 *a 1.306,1.185 1.497,1.350 0.191,0.166 10 *b 0.202,2.187 0.393,2.353 0.191,0.166 10 *c 1.372,2.76 1.563,2.925 0.191,0.166 10 *d 0.746,1.943 1.39,1.352 1.39,1.352 1.727,1.939 false 1.169,1.952 1.39,1.352 1.39,1.352 0.982,1.948 false 1.359,1.949 1.39,1.352 false 5.783,1.197 5.974,1.362 0.191,0.166 10 *b 6.778,2.179 6.969,2.344 0.191,0.166 10 *c 6.225,2.733 6.416,2.898 0.191,0.166 10 *d 6.586,1.937 5.864,1.363 5.864,1.363 5.604,1.945 false 6.026,1.952 5.864,1.363 5.864,1.363 6.215,1.949 false 5.835,1.948 5.864,1.363 false

Text in Illustration
*a Back Side *b Ceramic Notch
*c 7.6 mm (0.299 in.) *d 40 mm (1.575 in.)

HINT:

Only 2-piece type No. 2 windshield glass stoppers are supplied. Use the 2-piece type windshield glass stoppers even if a 1-piece type was used.



Hide 56115A 3.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B292040E01
0.737,0.659 0.926,0.817 0.189,0.157 10 *1 1.121,0.683 0.921,0.743 false

Install 2 new No. 1 windshield glass stoppers to the vehicle body, as shown in the illustration.

Text in Illustration
*1 No. 1 Windshield Glass Stopper

HINT:

Only 2-piece type No. 1 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.



Hide 56117A 4.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the application area of adhesive dam with Primer G.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



b.

Install a new adhesive dam onto the windshield glass, as shown in the illustration.

B272664E02
0.237,0.168 0.433,0.353 0.196,0.185 10 *a 5.546,0.809 5.742,0.995 0.196,0.185 10 *b 5.473,2.201 5.669,2.386 0.196,0.185 10 *c 2.454,0.694 2.576,0.851 0.122,0.157 10 A 2.454,1.156 2.576,1.312 0.122,0.157 10 A 3.696,1.968 3.817,2.124 0.122,0.157 10 B 3.202,2.053 3.324,2.210 0.122,0.157 10 B 1.33,2.521 1.452,2.677 0.122,0.157 10 C 1.33,3.005 1.452,3.162 0.122,0.157 10 C 4.467,0.648 5.155,0.804 0.688,0.157 10 A-A, B-B 4.467,2.083 4.745,2.239 0.278,0.157 10 C-C

Text in Illustration
*a Back Side *b 9.6 mm (0.378 in.)
*c 42.2 mm (1.661 in.) - -


Hide 56111 5.INSTALL WINDSHIELD GLASS

a.
B153152E01
0.249,0.812 0.418,0.967 0.169,0.155 10 *1 0.437,0.982 0.592,1.191 false 2.123,0.891 2.292,1.046 0.169,0.155 10 *1 2.311,1.062 2.457,1.298 false

Clean and shape the contact surface of the vehicle body.

Text in Illustration
*1 Adhesive

i.

Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.



b.
B292037E01
0.755,1.722 0.958,1.887 0.203,0.164 10 *a 1.279,2.117 0.944,1.842 0.944,1.842 1.222,2.208 false

Position the windshield glass.

Text in Illustration
*a Mark

i.

Using suction cups, place the windshield glass in the correct position.


ii.

Check that the whole contact surface of the windshield glass rim is perfectly even.


iii.

Align the matchmarks on the windshield glass and vehicle body.

NOTICE:

Check that the windshield glass stoppers are attached to the vehicle body correctly.



iv.

Remove the windshield glass.



c.
B271493E01
1.747,0.463 1.920,0.616 0.173,0.153 10 *1 1.769,1.515 1.942,1.667 0.173,0.153 10 *1 1.833,1.985 2.005,2.138 0.173,0.153 10 *2 3.009,0.488 3.182,0.640 0.173,0.153 10 *a 3.009,1.519 3.182,1.672 0.173,0.153 10 *b 1.94,0.586 2.276,0.861 false 1.962,1.634 2.272,1.8 false 2.025,2.051 2.228,1.918 false

Using a brush, coat the installation surface on the vehicle body with Primer M.

Text in Illustration
*1 Primer M
*2 Adhesive
*a Correct
*b Incorrect

NOTICE:
·

Do not coat the adhesive with Primer M.

·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Do not keep any of the opened Primer M for later use.




d.

Using a brush or sponge, coat the application areas that still have adhesive attached with Primer G.

B292042E01
0.431,3.521 0.735,3.717 0.304,0.195 10 : *1 0.106,0.04 0.329,0.235 0.223,0.195 10 *a 2.464,1.133 2.618,1.312 0.154,0.179 10 A 2.464,0.638 2.618,0.818 0.154,0.179 10 A 3.222,2.029 3.376,2.208 0.154,0.179 10 B 3.707,1.934 3.861,2.113 0.154,0.179 10 B 1.337,2.966 1.492,3.145 0.154,0.179 10 C 1.337,2.478 1.492,2.657 0.154,0.179 10 C 5.026,1.913 5.377,2.099 0.351,0.185 10 C-C 5.026,0.188 5.642,0.374 0.616,0.185 10 A-A, B-B 5.539,0.988 5.731,1.161 0.192,0.173 10 *b 5.844,2.187 6.036,2.360 0.192,0.173 10 *c

Text in Illustration
*1 Primer G - -
*a Back Side *b 8 mm (0.315 in.)
*c 19 mm (0.748 in.) - -

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:
·

Apply Primer G onto the ceramic notches.

·

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.




e.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B106205E08
2.395,0.851 2.579,1.020 0.184,0.170 10 *a 1.544,1.848 1.733,2.024 0.188,0.177 10 *b

Cut off the tip of the cartridge nozzle, as shown in the illustration.

Text in Illustration
*a 8.0 mm (0.315 in.)
*b 12.0 mm (0.472 in.)

HINT:

After cutting off the tip, use all adhesive within the time limit described in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour and 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with a cartridge.



f.

Apply adhesive to the windshield glass, as shown in the illustration.

B292043E01
0.43,3.534 0.747,3.716 0.317,0.182 10 : *1 0.129,0.069 0.330,0.251 0.201,0.181 10 *a 2.469,1.135 2.631,1.336 0.161,0.201 10 A 2.469,0.658 2.631,0.859 0.161,0.201 10 A 3.221,2.011 3.382,2.213 0.161,0.201 10 B 3.715,1.935 3.877,2.136 0.161,0.201 10 B 1.176,2.99 1.338,3.191 0.161,0.201 10 C 1.176,2.502 1.338,2.704 0.161,0.201 10 C 4.741,0.063 5.424,0.269 0.682,0.205 10 A-A, B-B 4.741,1.672 5.123,1.878 0.382,0.205 10 C-C 6.148,0.702 6.350,0.903 0.201,0.201 10 *c 5.728,0.274 5.929,0.475 0.201,0.201 10 *b 5.853,1.152 6.054,1.353 0.201,0.201 10 *d 6.552,2.617 6.753,2.818 0.201,0.201 10 *c 6.144,2.136 6.345,2.337 0.201,0.201 10 *d 5.501,3.043 5.703,3.244 0.201,0.201 10 *d 6.253,3.043 6.455,3.244 0.201,0.201 10 *d 5.593,1.919 5.795,2.120 0.201,0.201 10 *e

Text in Illustration
*1 Adhesive - -
*a Back Side *b 3.0 mm (0.118 in.)
*c 12.0 mm (0.472 in.) *d 8.0 mm (0.315 in.)
*e 30.5 mm (1.201 in.) - -


g.

Install the windshield glass.

i.
B292037E01
0.755,1.722 0.958,1.887 0.203,0.164 10 *a 1.279,2.117 0.944,1.842 0.944,1.842 1.222,2.208 false

Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

Text in Illustration
*a Mark

NOTICE:
·

Check that the windshield glass stoppers are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass.




ii.

Lightly press the front surface of the windshield glass to ensure a close fit.

HINT:

Press the glass with force of 98 N (10 kgf, 22 lb) or more.



iii.
B149738E08
2.921,1.148 2.921,1.463 false 0.71,0.129 0.898,0.280 0.188,0.151 10 *1 0.999,1.488 1.187,1.645 0.188,0.158 10 *2 0.018,0.826 0.187,0.977 0.169,0.151 10 *3 1.116,1.142 1.116,1.458 false 2.497,0.129 2.685,0.280 0.188,0.151 10 *1 2.817,1.481 3.005,1.638 0.188,0.158 10 *2 1.971,0.69 2.137,0.841 0.166,0.151 10 *3 0.206,0.939 0.502,1.124 false 0.799,0.295 0.799,0.837 false 2.599,0.312 2.599,0.838 false 2.145,0.856 2.417,1.148 false

If necessary, use a scraper to correct the level or position of adhesive that has been applied.

Text in Illustration
*1 Windshield
*2 Dam
*3 Adhesive

HINT:

Apply adhesive onto the windshield glass rim.




Hide 75533E 6.INSTALL WINDSHIELD OUTSIDE MOULDING

a.
B284431

Using a brush or sponge, coat the application area of the moulding with Primer G.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.




b.

Install a new moulding onto the windshield glass, as shown in the illustration.

B272665E01
2.301,0.224 2.422,0.373 0.121,0.149 10 A 2.301,0.723 2.422,0.872 0.121,0.149 10 A 4.861,0.822 5.124,0.971 0.263,0.149 10 A-A


c.
B292041E01
2.839,0.253 3.042,0.420 0.203,0.166 10 *1 2.635,0.648 2.831,0.374 false

Hold the windshield glass using Hold the windshield glass using protective tape until applied adhesive hardens. until applied adhesive hardens.

Text in Illustration
*1 Protective Tape

NOTICE:

Do not drive the vehicle within the time limits described in the table below.


Minimum time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours



Hide 7.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 8.INSTALL ROOF HEADLINING ASSEMBLY (for 5 Door)

(See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 5 Door)>INSTALLATION)

HINT:

Return the front section of the roof headlining assembly to the original position.


Hide 9.INSTALL ROOF HEADLINING ASSEMBLY (for 3 Door)

(See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 3 Door)>INSTALLATION)

HINT:

Return the front section of the roof headlining assembly to the original position.


Hide 87810 10.INSTALL INNER REAR VIEW MIRROR ASSEMBLY

Hide 11.INSTALL WINDSHIELD WIPER MOTOR AND LINK