Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2011.08–2014.07
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248389 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


a.

for LHD

U158216E02
2.167,0.76 2.365,0.938 0.198,0.177 10 false H1

i.

Disconnect the H1 power window regulator master switch assembly connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

w/ Rear Power Window
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H1-6 (B) - H1-1 (GND) GR - W-B Power supply Ignition switch ON 11 to 14 V
H1-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

w/o Rear Power Window
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H1-15 (B) - H1-7 (GND) GR - W-B Power supply Ignition switch ON 11 to 14 V
H1-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the power window regulator master switch assembly connector.


iv.

Measure the voltage according to the value(s) in the table below.

w/ Rear Power Window
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H1-8 (UP) - H1-1 (GND) R - W-B Power window motor UP operation Ignition switch ON, driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
H1-5 (DOWN) - H1-1 (GND) G - W-B Power window motor DOWN operation Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
H1-4 (AUTO) - H1-1 (GND) R - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V
H1-3 (LED) - H1-1 (GND) W - W-B LED illumination signal Ignition switch ON 11 to 14 V
Approximately 45 seconds after ignition switch turned off Below 1 V

w/o Rear Power Window
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H1-18 (UP) - H1-7 (GND) R - W-B Power window motor UP operation Ignition switch ON, driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
H1-10 (DOWN) - H1-7 (GND) G - W-B Power window motor DOWN operation Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
H1-1 (AUTO) - H1-7 (GND) R - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V
H1-6 (LED) - H1-7 (GND) W - W-B LED illumination signal Ignition switch ON 11 to 14 V
Approximately 45 seconds after ignition switch turned off Below 1 V

If the result is not as specified, the power window regulator master switch assembly may have a malfunction.



b.

for RHD

U158217E02
2.167,0.76 2.375,0.938 0.208,0.177 10 false G1

i.

Disconnect the G1 power window regulator master switch assembly connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

w/ Rear Power Window
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G1-6 (B) - G1-9 (GND) GR - W-B Power supply Ignition switch ON 11 to 14 V
G1-9 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

w/o Rear Power Window
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G1-15 (B) - G1-7 (GND) GR - W-B Power supply Ignition switch ON 11 to 14 V
G1-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the power window regulator master switch assembly connector.


iv.

Measure the voltage according to the value(s) in the table below.

w/ Rear Power Window
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G1-1 (UP) - G1-9 (GND) R - W-B Power window motor UP operation Ignition switch ON, driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
G1-5 (DOWN) - G1-9 (GND) G - W-B Power window motor DOWN operation Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
G1-4 (AUTO) - G1-9 (GND) R - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V
G1-3 (LED) - G1-9 (GND) W - W-B LED illumination signal Ignition switch ON 11 to 14 V
Approximately 45 seconds after ignition switch turned off Below 1 V

w/o Rear Power Window
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G1-9 (UP) - G1-7 (GND) R - W-B Power window motor UP operation Ignition switch ON, driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
G1-6 (DOWN) - G1-7 (GND) G - W-B Power window motor DOWN operation Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
G1-18 (AUTO) - G1-7 (GND) R - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V
G1-16 (LED) - G1-7 (GND) W - W-B LED illumination signal Ignition switch ON 11 to 14 V
Approximately 45 seconds after ignition switch turned off Below 1 V

If the result is not as specified, the power window regulator master switch assembly may have a malfunction.




CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER SIDE)


a.

for LHD

U158218E02
2.323,0.76 2.521,0.938 0.198,0.177 10 false G2

i.

Disconnect the G2 power window regulator switch assembly (front passenger side) connector.


ii.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G2-3 (B) - Body ground L - Body ground Power supply Ignition switch ON 11 to 14 V
G2-5 (SU) - Body ground W - Body ground Ground Always Below 1 Ω
G2-2 (SD) - Body ground P - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the G2 power window regulator switch assembly (front passenger side) connector.


iv.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G2-4 (U) - Body ground LA-R - Body ground Power window motor UP operation Front passenger side power window switch OFF → UP Below 1 V → 11 to 14 V
G2-1 (D) - Body ground LA-G - Body ground Power window motor DOWN operation Front passenger side power window switch OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator switch assembly (front passenger side) may have a malfunction.



b.

for RHD

U158219E02
2.323,0.771 2.521,0.948 0.198,0.177 10 false H2

i.

Disconnect the H2 power window regulator switch assembly (front passenger side) connector.


ii.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-3 (B) - Body ground L - Body ground Power supply Ignition switch ON 11 to 14 V
H2-5 (SU) - Body ground W - Body ground Ground Always Below 1 Ω
H2-2 (SD) - Body ground P - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the H2 power window regulator switch assembly (front passenger side) connector.


iv.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-4 (U) - Body ground LA-R - Body ground Power window motor UP operation Front passenger side power window switch OFF → UP Below 1 V → 11 to 14 V
H2-1 (D) - Body ground LA-G - Body ground Power window motor DOWN operation Front passenger side power window switch OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator switch assembly (front passenger side) may have a malfunction.




CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH


U158220E02
2.333,0.76 2.51,0.938 0.177,0.177 10 false J1

a.

Disconnect the J1 rear power window regulator switch assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-3 (B) - Body ground LA-SB - Body ground Power supply Ignition switch ON 11 to 14 V
J1-5 (SU) - Body ground LA-R - Body ground Ground Always Below 1 Ω
J1-2 (SD) - Body ground LA-G - Body ground Ground Always Below 1 Ω


c.

Reconnect the J1 rear power window regulator switch assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-4 (U) - Body ground LA-Y - Body ground Power window motor UP operation Front passenger side power window switch OFF → UP Below 1 V → 11 to 14 V
J1-1 (D) - Body ground LA-B - Body ground Power window motor DOWN operation Front passenger side power window switch OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the rear power window regulator switch assembly LH may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH


U158221E02
2.365,0.771 2.542,0.948 0.177,0.177 10 false I1

a.

Disconnect the I1 rear power window regulator switch assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I1-3 (B) - Body ground LA-SB - Body ground Power supply Ignition switch ON 11 to 14 V
I1-5 (SU) - Body ground LA-R - Body ground Ground Always Below 1 Ω
I1-2 (SD) - Body ground LA-G - Body ground Ground Always Below 1 Ω


c.

Reconnect the I1 rear power window regulator switch assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I1-4 (U) - Body ground LA-Y - Body ground Power window motor UP operation Front passenger side power window switch OFF → UP Below 1 V → 11 to 14 V
I1-1 (D) - Body ground LA-B - Body ground Power window motor DOWN operation Front passenger side power window switch OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the rear power window regulator switch assembly RH may have a malfunction.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH (DRIVER SIDE)


a.

for LHD

U158222E02
2.49,0.698 2.688,0.875 0.198,0.177 10 false H3

i.

Disconnect the H3 power window regulator motor assembly LH connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H3-2 (B) - H3-1 (GND) G - W-B Power supply Always 11 to 14 V
H3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the power window regulator motor assembly LH connector.


iv.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H3-10 (UP) - H3-1 (GND) R - W-B Power window motor UP operation Ignition switch ON, driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
H3-7 (DOWN) - H3-1 (GND) G - W-B Power window motor DOWN operation Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
H3-4 (AUTO) - H3-1 (GND) R - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V
H3-5 (LED) - H3-1 (GND) W - W-B LED illumination signal Ignition switch ON 11 to 14 V
Approximately 45 seconds after ignition switch turned off Below 1 V

If the result is not as specified, the power window regulator motor assembly LH may have a malfunction.



b.

for RHD

U158223E02
2.469,0.708 2.677,0.885 0.208,0.177 10 false G3

i.

Disconnect the G3 power window regulator motor assembly RH connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G3-2 (B) - G3-1 (GND) G - W-B Power supply Always 11 to 14 V
G3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the power window regulator motor assembly RH connector.


iv.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G3-10 (UP) - G3-1 (GND) R - W-B Power window motor UP operation Ignition switch ON, driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
G3-7 (DOWN) - G3-1 (GND) G - W-B Power window motor DOWN operation Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
G3-4 (AUTO) - G3-1 (GND) R - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V
G3-5 (LED) - G3-1 (GND) W - W-B LED illumination signal Ignition switch ON 11 to 14 V
Approximately 45 seconds after ignition switch turned off Below 1 V

If the result is not as specified, the power window regulator motor assembly RH may have a malfunction.




CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU


U158694E02
1.01,0.948 1.208,1.094 0.198,0.146 10 false 3D 0.292,0.125 0.438,0.271 0.146,0.146 10 false *1 0.948,6.677 1.115,6.833 0.167,0.156 10 false *2 1.531,3.854 1.729,4 0.198,0.146 10 false 3D 3.802,0.781 4.031,0.948 0.229,0.167 10 false MB 3.802,2.865 4.031,3.021 0.229,0.156 10 false MB 1.01,1.583 1.208,1.74 0.198,0.156 10 false 3C 4.01,3.854 4.219,4 0.208,0.146 10 false 3C 6.385,0.948 6.583,1.094 0.198,0.146 10 false 3B 6.385,1.583 6.583,1.729 0.198,0.146 10 false 3A 5.479,5.219 5.677,5.365 0.198,0.146 10 false 3A 3.792,6.448 4.052,6.594 0.26,0.146 10 false F76 3.688,7.51 3.958,7.656 0.271,0.146 10 false F76 1.698,5.229 1.896,5.375 0.198,0.146 10 false 3B 1.021,2.115 1.219,2.271 0.198,0.156 10 false 3F 6.344,3.854 6.531,4 0.188,0.146 10 false 3F 0.469,2.115 0.667,2.271 0.198,0.156 10 false 3E 5.781,3.854 5.979,4.01 0.198,0.156 10 false 3E 5.781,3.646 5.948,3.802 0.167,0.156 10 false *A 6.354,3.646 6.521,3.802 0.167,0.156 10 false *B 0.479,1.906 0.646,2.063 0.167,0.156 10 false *A 1.021,1.896 1.188,2.052 0.167,0.156 10 false *B

Text in Illustration
*A for LHD *B for RHD
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU

a.

Remove the main body ECU.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-29 (ACC) - Body ground - Ignition power supply (ACC signal) Ignition switch ACC 11 to 14 V
MB-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply (IG signal) Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reinstall the main body ECU.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F76-2 (KOFF) - Body ground L - Body ground Power window relay operation signal Ignition switch ON 11 to 14 V
Approximately 45 seconds after ignition switch turned off Below 1 V
F76-19 (FRCY) - Body ground Y - Body ground Front door courtesy light switch RH signal Front door RH opened Below 1 V
Front door RH closed Pulse generation
3D-36 (FLCY) - Body ground L - Body ground Front door courtesy light switch LH signal Front door LH opened Below 1 V
Front door LH closed Pulse generation
3B-12 (LIN2) - Body ground W - Body ground LIN communication signal Ignition switch ON Pulse generation

HINT:

If the result is not as specified, the main body ECU or instrument panel junction block assembly may have a malfunction.