Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248389 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the Intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus:

for D-Door Motor: Body / D-Door Motor / Data List

for Main Body: Body / Main Body / Data List



e.

According to the display on the intelligent tester, read the Data List.

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window auto switch signal /
OFF or ON
OFF: Driver side door power window auto switch not operated
ON: Driver side door power window auto switch operated
-
D Door P/W Up SW Driver side power window manual up switch signal /
OFF or ON
OFF: Driver side door power window manual up switch not operated
ON: Driver side door power window manual up switch operated
-
D Door P/W Down SW Driver side power window manual down switch signal /
OFF or ON
OFF: Driver side door power window manual down switch not operated
ON: Driver side door power window manual down switch operated
-
Glass Position (Close - 1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position /
OK or Caution
OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (1/4 - 2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position /
OK or Caution
OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (2/4 - 3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position /
OK or Caution
OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (3/4 - Open) Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position /
OK or Caution
OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Number of Trouble Codes Number of trouble codes /
Min.: 0
Max.: 255
Number of DTCs will be displayed -

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Courtesy Front door courtesy light switch RH signal /
ON or OFF
ON: Front door RH closed
OFF: Front door RH opened
-
FL Door Courtesy Front door courtesy light switch LH signal /
ON or OFF
ON: Front door LH closed
OFF: Front door LH opened
-



ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the Intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


D-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF / DOWN / UP -