Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248389 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Rear Power Window LH does not Operate with Rear Power Window Switch LH  


DESCRIPTION

If the rear LH side manual UP / DOWN function does not operate, a malfunction may exist in the rear power window regulator motor assembly LH, rear power window regulator switch assembly LH, power window regulator master switch assembly or wire harness.

WIRING DIAGRAM

B291670E01
0.11,2.005 1.104,2.170 0.994,0.165 10 from P/W Relay 1.52,2.154 2.227,2.296 0.707,0.142 10 DOOR R/L 2.536,1.923 2.645,2.070 0.109,0.147 10 3 2.739,2.005 2.853,2.156 0.114,0.151 10 B 0.773,3.751 1.484,3.893 0.711,0.142 10 *1: for LHD 0.773,4.064 1.512,4.206 0.739,0.142 10 *2: for RHD 2.412,3.896 2.586,4.066 0.174,0.170 10 J1 2.412,4.069 4.346,4.401 1.934,0.332 10 Rear Power Window Regulator Switch Assembly LH 5.214,3.433 5.410,3.571 0.196,0.138 10 H1 5.557,3.431 5.760,3.572 0.203,0.141 10 G1 5.211,2.808 5.413,2.953 0.202,0.145 10 H1 5.556,2.807 5.762,2.954 0.207,0.147 10 G1 5.222,2.626 5.402,2.777 0.180,0.150 10 12 5.57,2.63 5.748,2.773 0.178,0.143 10 18 5.218,3.245 5.406,3.396 0.188,0.151 10 13 5.561,3.249 5.757,3.393 0.195,0.144 10 10 5.438,3.901 7.048,4.214 1.610,0.313 10 Power Window Regulator Master Switch Assembly 5.214,1.645 5.384,1.801 0.170,0.156 10 J2 5.214,1.813 7.152,2.145 1.938,0.332 10 Rear Power Window Regulator Motor Assembly LH 5.672,0.499 5.786,0.664 0.114,0.165 10 1 5.662,1.135 5.767,1.286 0.105,0.151 10 2 4.098,0.503 4.217,0.659 0.119,0.156 10 4 4.098,1.133 4.208,1.288 0.110,0.156 10 1 3.897,0.599 4.021,0.750 0.123,0.151 10 U 3.897,1.229 4.021,1.376 0.123,0.147 10 D 4.098,2.719 4.206,2.872 0.108,0.153 10 5 4.098,3.327 4.194,3.488 0.096,0.161 10 2 3.804,2.802 4.020,2.958 0.216,0.156 10 SU 3.804,3.428 4.020,3.575 0.216,0.147 10 SD 5.873,2.805 5.996,2.956 0.123,0.151 10 U 5.873,3.428 5.996,3.575 0.123,0.147 10 D 5.227,2.992 5.397,3.153 0.170,0.161 10 *1 5.574,2.992 5.744,3.153 0.170,0.161 10 *2 5.227,3.621 5.397,3.781 0.170,0.161 10 *1 5.574,3.621 5.744,3.781 0.170,0.161 10 *2 5.873,0.599 5.996,0.750 0.123,0.151 10 U 5.873,1.229 5.996,1.376 0.123,0.147 10 D

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
a.

Inspect the rear power window regulator switch assembly LH (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION).



OK

2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Inspect the rear power window regulator motor assembly LH (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - P/W RELAY)

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - P/W RELAY)
a.

Disconnect the J1 rear power window regulator switch assembly LH connector.


U158230E01
0.089,0.058 0.259,0.218 0.170,0.161 10 *a 0.629,1.103 0.796,1.249 0.167,0.146 10 J1 1.792,1.601 1.905,1.746 0.113,0.145 10 B 1.755,1.288 1.851,1.579 false

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J1-3 (B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Rear Power Window Regulator Switch Assembly LH)



OK

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the J1 rear power window regulator switch assembly LH connector.


b.

Disconnect the J2 rear power window regulator motor assembly LH connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-4 (U) - J2-1 (U) Always Below 1 Ω
J1-1 (D) - J2-2 (D) Always Below 1 Ω
J1-4 (U) - Body ground Always 10 kΩ or higher
J1-1 (D) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
a.

for LHD

i.

Disconnect the J1 rear power window regulator switch assembly LH connector.


ii.

Disconnect the H1 power window regulator master switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-5 (SU) - H1-12 (U) Always Below 1 Ω
J1-2 (SD) - H1-13 (D) Always Below 1 Ω
J1-5 (SU) - Body ground Always 10 kΩ or higher
J1-2 (SD) - Body ground Always 10 kΩ or higher




b.

for RHD

i.

Disconnect the J1 rear power window regulator switch assembly LH connector.


ii.

Disconnect the G1 power window regulator master switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-5 (SU) - G1-18 (U) Always Below 1 Ω
J1-2 (SD) - G1-10 (D) Always Below 1 Ω
J1-5 (SU) - Body ground Always 10 kΩ or higher
J1-2 (SD) - Body ground Always 10 kΩ or higher





OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR