58410B
1.REMOVE DECK BOARD ASSEMBLY
64771G
2.REMOVE SPARE WHEEL COVER
3.REMOVE FRONT SEAT ASSEMBLY (for Driver Side)
4.REMOVE FRONT SEAT ASSEMBLY (for Front Passenger Side)
5.REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
6.REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
7.REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)
58910C
8.REMOVE REAR CONSOLE BOX ASSEMBLY
67913
9.REMOVE FRONT DOOR SCUFF PLATE RH
67914
10.REMOVE FRONT DOOR SCUFF PLATE LH
Use the same procedure as for the RH side.
62111C
11.REMOVE COWL SIDE TRIM BOARD RH
62112
12.REMOVE COWL SIDE TRIM BOARD LH
Use the same procedure as for the RH side.
67917A
13.REMOVE REAR DOOR SCUFF PLATE RH
67918A
14.REMOVE REAR DOOR SCUFF PLATE LH
Use the same procedure as for the RH side.
58387B
15.REMOVE REAR FLOOR FINISH PLATE
73370
16.SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
Use the same procedure as for the RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 5 Door)>REMOVAL)
62332A
17.SEPARATE REAR DOOR OPENING TRIM WEATHERSTRIP
Separate the rear door opening trim weatherstrip.
81250
18.REMOVE NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)
64740C
19.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Use the same procedure as for the RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 5 Door)>REMOVAL)
58442F
20.REMOVE JACK COVER
09110
21.REMOVE JACK ASSEMBLY
58510D
22.REMOVE FRONT FLOOR CARPET ASSEMBLY
Disengage the 6 clamps.
Remove the clip and front floor carpet.
77306
23.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
Remove the bolt.
Slide the fuel lid lock open lever as indicated by the arrow as shown in the illustration.
Disengage the guide and separate the fuel lid lock control cable.
77035
24.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for LHD)
Disengage the 2 claws and separate the fuel lid lock control cable.
Disengage the 4 clamps and remove the fuel lid lock control cable as shown in the illustration.
| *1 | Fuel Lid Lock Control Cable Sub-assembly | *2 | Wire Harness Clamp |
77035
25.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for RHD)
Disengage the 2 claws and separate the fuel lid lock control cable.
Disengage the 7 clamps and remove the fuel lid lock control cable as shown in the illustration.
| *1 | Fuel Lid Lock Control Cable Sub-assembly | *2 | Wire Harness Clamp |
77377
26.REMOVE FUEL FILLER OPENING LID LOCK RETAINER
Rotate the fuel filler opening lid lock retainer by 90° and disengage the 2 claws A from the 2 slits as shown in the illustration.
| *1 | Claw A |
| *a | Slit |
| *b | Rotate |
Rotate the fuel filler opening lid lock retainer by another 90° and remove it by disengaging the 2 claws B from the 2 slits as shown in the illustration.
| *1 | Claw B |
| *a | Slit |
| *b | Rotate |