Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER RUBBER
RM19S0E _59 Vehicle Exterior _051504 WIPER / WASHER _0248408 REAR WIPER RUBBER A

WIPER / WASHER  REAR WIPER RUBBER  REPLACEMENT  


PROCEDURE

Hide 85220R 1.REMOVE REAR WIPER BLADE ASSEMBLY

a.
E229011

Raise the wiper blade to the position where the claw disengages with a click sound, as shown in the illustration.

NOTICE:

Be careful not to damage the claw.



b.
E229012

Remove the rear wiper blade from the rear wiper arm in the direction indicated by the arrow in the illustration.

NOTICE:

Do not fold the wiper arm with the wiper blade removed. The arm tip may damage the back door glass surface.



Hide 85214R 2.REMOVE REAR WIPER RUBBER

a.
E156176E02
2.794,1.564 2.531,1.818 false 2.354,1.808 2.510,1.989 0.156,0.181 10 *1

Lift and pull the end of the wiper rubber protrusion from the blade stopper as shown in the illustration.

NOTICE:

Do not forcibly pull out the wiper rubber. The backing plates will be deformed or the blade claws will be damaged.


HINT:

Lightly pushing the rubber in the middle will allow it to be removed more easily.


Text in Illustration
*1 Stopper


b.
E125273

Remove the rear wiper rubber with the 2 rear wiper rubber backing plates.


c.

Remove the 2 rear wiper rubber backing plates from the rear wiper rubber.


Hide 85214R 3.INSTALL REAR WIPER RUBBER

a.

Install the 2 rear wiper rubber backing plates to the rear wiper rubber as shown in the illustration.

NOTICE:
E156177

Install the backing plates facing the correct direction.



b.
E156178E01
0.719,1.354 0.383,1.583 false 1.093,2.033 1.571,1.787 false 1.082,2.142 0.604,1.896 false 0.181,1.51 0.346,1.667 0.165,0.157 10 *1 0.409,1.811 0.574,1.968 0.165,0.157 10 *3 1.601,1.697 1.766,1.854 0.165,0.157 10 *2

Insert the wiper rubber from the second claws of the wiper blade to the rear end claws.


c.

After pushing the wiper rubber through the rear end claws, allow it to stick out from the rear end stopper.

Text in Illustration
*1 Second Claws
*2 Rear End Claws
*3 Rear End Stopper


d.
E184498E04
1.615,0.427 1.26,0.594 false 1.115,0.5 1.313,0.688 0.198,0.188 10 false *1

Slide the wiper rubber through the front end claws.

NOTICE:

Do not deform the rear wiper rubber backing plate or damage the rear wiper blade assembly claws by sliding the rear wiper rubber excessively.


Text in Illustration
*1 Front End Claws

HINT:
·

If the rear wiper blade assembly claws are not through the grooves in the rear wiper rubber, slide the rear wiper rubber back and forth several times to engage the claws.

·

Applying a small amount of washer fluid to the rear wiper rubber allows the claws to align the grooves.

·
E184500

The rear wiper rubber slide stroke is extended by lifting the center of the rear wiper rubber slightly as shown in the illustration.




Hide 85220R 4.INSTALL REAR WIPER BLADE ASSEMBLY

a.
E229013

Engage the claw and install the rear wiper blade to the wiper arm in the illustration.