Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2014.07
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248415 LIGHTING SYSTEM U

LIGHTING (EXT)  LIGHTING SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU


U158678E03
1,0.958 1.198,1.104 0.198,0.146 10 false 3D 0.802,0.125 0.948,0.271 0.146,0.146 10 false *1 0.938,6.688 1.104,6.844 0.167,0.156 10 false *2 1.521,3.854 1.719,4 0.198,0.146 10 false 3D 3.802,0.792 4.031,0.958 0.229,0.167 10 false MB 3.802,2.865 4.031,3.021 0.229,0.156 10 false MB 1,1.583 1.198,1.74 0.198,0.156 10 false 3C 4,3.865 4.208,4.01 0.208,0.146 10 false 3C 6.385,0.958 6.583,1.104 0.198,0.146 10 false 3B 6.385,1.583 6.583,1.729 0.198,0.146 10 false 3A 5.469,5.229 5.667,5.375 0.198,0.146 10 false 3A 3.802,6.448 4.063,6.594 0.26,0.146 10 false F76 3.688,7.5 3.948,7.646 0.26,0.146 10 false F76 1.688,5.229 1.885,5.375 0.198,0.146 10 false 3B 1,2.125 1.198,2.281 0.198,0.156 10 false 3F 6.073,3.875 6.271,4.031 0.198,0.156 10 false 3F 0.146,0.083 0.333,0.26 0.188,0.177 10 false *A

Text in Illustration
*A Main Body ECU 1 Connector Type - -
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU

U158680E03
0.917,0.948 1.125,1.094 0.208,0.146 10 false 3D 1.458,3.875 1.656,4.021 0.198,0.146 10 false 3D 3.958,3.865 4.177,4.01 0.219,0.146 10 false 3C 6.073,3.865 6.281,4.021 0.208,0.156 10 false 3F 0.146,0.083 0.344,0.25 0.198,0.167 10 false *A 0.719,0.156 0.875,0.302 0.156,0.146 10 false *1 0.865,6.719 1.042,6.865 0.177,0.146 10 false *2 3.792,0.823 4.021,0.979 0.229,0.156 10 false MB 3.667,2.896 3.906,3.042 0.24,0.146 10 false MB 0.917,1.583 1.156,1.75 0.24,0.167 10 false 3C 0.917,2.115 1.125,2.271 0.208,0.156 10 false 3F 6.375,0.979 6.573,1.125 0.198,0.146 10 false 3B 1.615,5.26 1.813,5.406 0.198,0.146 10 false 3B 5.385,5.208 5.594,5.354 0.208,0.146 10 false 3A 6.375,1.625 6.573,1.781 0.198,0.156 10 false 3A 2.448,7.51 2.802,7.656 0.354,0.146 10 false F136 2.896,6.479 3.25,6.625 0.354,0.146 10 false F136 3.646,6.469 3.906,6.615 0.26,0.146 10 false F76 4.823,7.49 5.104,7.635 0.281,0.146 10 false F76

Text in Illustration
*A Main Body ECU 2 Connector Type - -
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU

a.

Remove the main body ECU.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-29 (ACC) - Body ground - Ignition power supply (ACC signal) Ignition switch ACC 11 to 14 V
MB-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply (IG signal) Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reinstall the main body ECU.


d.

Measure the voltage resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F76-5 (HU) - Body ground*1 P - Body ground Dimmer switch high signal Dimmer switch in high position Below 1 V
Dimmer switch in low position Pulse generation
F76-8 (HF) - Body ground*1 P - Body ground Dimmer switch high flash signal Dimmer switch in high flash position Below 1 V
Dimmer switch not in high flash position Pulse generation
F76-20 (CLTB) - Body ground*1 W - Body ground Automatic light control sensor power supply Ignition switch ON 11 to 14 V
F76-21 (CLTS) - Body ground*1 B - Body ground Automatic light control sensor signal Ignition switch off Below 1 V
Ignition switch ON and light control switch in AUTO Pulse generation
(See waveform 1)
F76-22 (CLTE) - Body ground*1 G - Body ground Automatic light control sensor ground Ignition switch off Below 1 Ω
F76-27 (FFOG) - Body ground*2 G - Body ground Fog light switch signal Fog light switch on Below 1 V
Fog light switch off Pulse generation
F76-28 (A) - Body ground*1 V - Body ground Light control switch AUTO signal Light control switch in AUTO position Below 1 V
Light control switch not in AUTO position Pulse generation
F76-29 (HEAD) - Body ground*1 L - Body ground Light control switch head signal Light control switch in head position Below 1 V
Light control switch not in head position Pulse generation
F76-30 (TAIL) - Body ground)*1 SB - Body ground Light control switch tail signal Light control switch in tail or head position Below 1 V
Light control switch in neither tail nor head position Pulse generation
3C-18 (HRLY) - Body ground V - Body ground Headlight relay drive output Light control switch in head Below 1 V
Light control switch not in head 11 to 14 V
3C-35 (DIM) - Body ground P - Body ground Dimmer relay drive output Dimmer switch in high or high flash position Below 1 V
Dimmer switch in low position 11 to 14 V
F136-21 (RLEW)*3 - Body ground V - Body ground Light control ECU RH signal input Ignition switch ON (IG), light control switch off 11 to 14 V
Ignition switch ON (IG), light control switch in head position Pulse generation
F136-24 (LLEW)*3 - Body ground SB - Body ground Light control ECU LH signal input Ignition switch ON (IG), light control switch off 11 to 14 V
Ignition switch ON (IG), light control switch in head position Pulse generation

*1: w/ Automatic Light Control System

*2: w/ Fog Light

*3: for LED Headlight


HINT:

If the result is not as specified, the main body ECU or instrument panel junction block assembly may have a malfunction.


i.
B113714E06
2.958,1.03 3.302,1.190 0.344,0.160 10 GND 1.859,1.362 1.988,1.522 0.129,0.160 10 A

Waveform 1

Item Content
Terminal No. (Symbol) F76-21 (CLTS) - Body ground
Tool setting 5 V/DIV., 5 ms./DIV.
Condition Ignition switch ON and light control switch in AUTO

HINT:

If the ambient light becomes brighter, width A becomes narrower.





CHECK COMBINATION METER ASSEMBLY


E346268E01
3.365,0.24 3.781,0.479 0.417,0.24 3.5,0.26 3.813,0.458 0.313,0.198 10 false F3

a.

Disconnect the F3 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F3-1 (B) - Body ground R - Body ground Battery power supply Always 11 to 14 V

HINT:

If the result is not as specified, there may be a malfunction on the wire harness.



c.

Reconnect the combination meter assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F3-3 (HAZ) - Body ground L - Body ground Hazard warning signal switch signal Hazard warning signal switch off 11 to 14 V
Hazard warning signal switch on Below 1 V
F3-7 (LR) - Body ground V - Body ground Turn signal light RH drive output Turn signal light RH turned on 11 to 14 V
Turn signal light RH turned off Below 1 V
F3-9 (ER) - Body ground B - Body ground Turn signal switch RH signal Turn signal switch RH on Below 1 V
Turn signal switch RH off 11 to 14 V
F3-10 (EL) - Body ground Y - Body ground Turn signal switch LH signal Turn signal switch LH on Below 1 V
Turn signal switch LH off 11 to 14 V
F3-13 (LL) - Body ground LG - Body ground Turn signal light LH drive output Turn signal light LH turned on 11 to 14 V
Turn signal light LH turned off Below 1 V

HINT:

If the result is not as specified, the combination meter assembly may have a malfunction.