Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2014.07
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248427 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM J

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  Headlight Leveling ECU Power Source Circuit  


DESCRIPTION

This circuit detects the state of the ignition switch, and sends it to the headlight leveling ECU assembly.

WIRING DIAGRAM

E223770E27
4.844,2.76 7.021,2.948 2.177,0.188 10 false Headlight Leveling ECU Assembly 4.844,2.583 5.125,2.771 0.281,0.188 10 false A82 0.615,1.063 1.979,1.25 1.365,0.188 10 false from IG1 NO. 1 Relay 5.479,1.083 5.677,1.281 0.198,0.198 10 false IG 5.479,2.167 5.677,2.365 0.198,0.198 10 false E1 5.281,2.063 5.385,2.208 0.104,0.146 10 false 9 5.271,0.969 5.396,1.146 0.125,0.177 10 false 1 3.396,1.25 4.323,1.438 0.927,0.188 10 false ECU-IG NO. 2

CAUTION / NOTICE / HINT

NOTICE:

The fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS (+B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL Auto Leveling / Data List.


e.

Read the display on the GTS.

HL Auto Leveling
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
+B IG power supply voltage value / 0.00 to 19.75 V 11 to 14 V -

OK:

Normal condition listed above is displayed




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT LEVELING ECU ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT LEVELING ECU ASSEMBLY)
a.
U158648E01
0.096,0.038 0.351,0.230 0.255,0.192 10 *a 1.638,0.453 1.957,0.615 0.318,0.163 10 A82 0.237,1.59 0.463,1.753 0.227,0.163 10 IG 0.662,1.318 0.338,1.573 false

Disconnect the headlight leveling ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A82-1 (IG) - Body ground Ignition switch ON 11 to 14 V
A82-1 (IG) - Body ground Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A82-9 (E1) - Body ground Always Below 1 Ω




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR