Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2014.07
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248427 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM J

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  Headlight Signal Circuit  


DESCRIPTION

The headlight leveling ECU assembly detects the status of the low beam headlights.

WIRING DIAGRAM

E299291E01
0.604,1.094 2.260,1.245 1.656,0.151 10 from H-LP/US-DRL Relay 5.25,0.943 5.360,1.085 0.110,0.142 10 3 5.25,2.063 5.360,2.205 0.110,0.142 10 9 5.457,1.1 5.852,1.242 0.394,0.142 10 HDLP 5.457,2.183 5.652,2.325 0.194,0.142 10 E1 4.85,2.596 5.131,2.738 0.281,0.142 10 A82 4.85,2.754 6.995,2.899 2.145,0.145 10 Headlight Leveling ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

First check that the low beam headlights operate normally.


PROCEDURE

1.READ VALUE USING GTS (HEADLIGHT LOW BEAM STATE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL Auto Leveling / Data List.


e.

Read the display on the GTS.

HL Auto Leveling
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Headlight Low Beam State Low beam headlight state/ON or OFF ON: Low beam headlights on
OFF: Low beam headlights off
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - POWER SOURCE)
a.
U158646E01
0.096,0.063 0.351,0.255 0.255,0.192 10 *a 1.638,0.477 1.957,0.640 0.318,0.163 10 A82 1.331,1.819 1.729,1.962 0.398,0.143 10 HDLP 1.308,1.897 1.041,1.344 false

Disconnect the headlight leveling ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A82-3 (HDLP) - Body ground Ignition switch ON 11 to 14 V
A82-3 (HDLP) - Body ground Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A82-9 (E1) - Body ground Always Below 1 Ω




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR