Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER(except Sport Package) › 2011.08–2014.07
RM19S0E _59 Vehicle Exterior _051507 EXTERIOR PANELS / TRIM _0248432 FRONT BUMPER(except Sport Package) A

EXTERIOR PANELS / TRIM  FRONT BUMPER(except Sport Package)  REASSEMBLY  


PROCEDURE

Hide 52601 1.INSTALL FRONT BUMPER ENERGY ABSORBER SUB-ASSEMBLY (w/ Front Bumper Lower Absorber)

a.
B271837

Engage the 3 hooks and install the front bumper energy absorber.


b.
B271836

Install the 6 screws, the 6 clips and grommet.


Hide 51441C 2.INSTALL ENGINE UNDER COVER RH (w/ Front Bumper Lower Absorber)

Hide 51442C 3.INSTALL ENGINE UNDER COVER LH (w/ Front Bumper Lower Absorber)

Hide 57014A 4.INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH

a.
B271835

Engage the 2 guides and install the front side member bracket.


b.

Tighten the 4 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 57013C 5.INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 85330 6.INSTALL WINDSHIELD WASHER JAR ASSEMBLY

a.
B288481

Install the windshield washer jar with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 53165A 7.INSTALL FRONT NO. 1 BUMPER STONE DEFLECTOR BRACKET

a.
B271834

Install the front No. 1 bumper stone deflector bracket with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Use the same procedure as for the opposite side.



Hide 52131A 8.INSTALL FRONT BUMPER REINFORCEMENT

a.
B271833

Install the front bumper reinforcement with the 4 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Tighten the 6 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


c.
B271832

Engage the 2 clamps and install the wire harness.


Hide 52611 9.INSTALL FRONT BUMPER ENERGY ABSORBER (w/ Energy Absorber)

a.
B288635

Engage the 2 guides and install the front bumper energy absorber.


Hide 53286B 10.INSTALL NO. 2 RADIATOR SIDE AIR SEAL (w/ Energy Absorber)

a.
B271829

Engage the 2 claws and install the radiator side air seal.


Hide 53285B 11.INSTALL NO. 1 RADIATOR SIDE AIR SEAL (w/ Energy Absorber)

HINT:

Use the same procedure as for the No. 2 side.


Hide 53286B 12.INSTALL NO. 2 RADIATOR SIDE AIR SEAL (w/o Energy Absorber)

a.
B288477

Engage the 2 claws and install the radiator side air seal.


Hide 53285B 13.INSTALL NO. 1 RADIATOR SIDE AIR SEAL (w/o Energy Absorber)

HINT:

Use the same procedure as for the No. 2 side.


Hide 53288B 14.INSTALL RADIATOR SUPPORT EXTENSION LH (w/ Energy Absorber)

a.
B273105

Engage the 2 claws and install the radiator support extension.


Hide 53287B 15.INSTALL RADIATOR SUPPORT EXTENSION RH (w/ Energy Absorber)

HINT:

Use the same procedure as for the LH side.


Hide 53288B 16.INSTALL RADIATOR SUPPORT EXTENSION LH (w/o Energy Absorber)

a.
B288478

Engage the 2 claws and install the radiator support extension.


Hide 53287B 17.INSTALL RADIATOR SUPPORT EXTENSION RH (w/o Energy Absorber)

HINT:

Use the same procedure as for the No. 2 side.


Hide 88790B 18.INSTALL THERMISTOR ASSEMBLY

a.
B271830

Engage the 2 clamps and install the thermistor.


Hide 52536 19.INSTALL FRONT BUMPER SIDE RETAINER LH

a.
B271827

Engage the 2 claws and install the front bumper side retainer.


Hide 52535 20.INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 81110 22.INSTALL HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 81482C 23.INSTALL FOG LIGHT COVER LH

a.
B271825

Engage the 5 claws and install the fog light cover.


Hide 81481E 24.INSTALL FOG LIGHT COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 81220 25.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

Hide 81210A 26.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Use the same procedure as for the LH side.


Hide 53112E 27.INSTALL LOWER NO. 1 RADIATOR GRILLE

a.
B288476

Engage the 14 claws and install the lower No. 1 radiator grille.


Hide 52127C 28.INSTALL FRONT BUMPER HOLE COVER

a.
B271823

Engage the 3 claws and install the front bumper hole cover.


Hide 52129B 29.INSTALL FRONT BUMPER LOWER COVER

a.
B271822

Engage the 3 claws and install the front bumper lower cover.


Hide 75311 30.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM

a.
B283029

Engage the 2 guides, 4 claws and install the radiator grille (or front panel) emblem.


Hide 53111 31.INSTALL RADIATOR GRILLE

a.
B271820

Engage the 14 claws and install the radiator grille.


b.
B271818

Install the 3 clips.


Hide 53124B 32.INSTALL RADIATOR GRILLE SIDE MOULDING LH

a.
B271819

Engage the 4 claws and install the radiator grille side moulding.


Hide 53123B 33.INSTALL RADIATOR GRILLE SIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 53395E 34.INSTALL HOOD TO FRONT END PANEL SEAL

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided adhesive tape remaining on the front bumper cover.

HINT:

Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



ii.

Using a piece of cloth, rub the remaining double-sided adhesive tape off the front bumper cover while it is hot from the infrared light.

NOTICE:

Installing the hood to front end panel seal with any double-sided tape remaining on the front bumper cover may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B283047

Install a new hood to front end panel seal onto the front bumper cover, as shown in the illustration.

NOTICE:

Thoroughly press the hood to front end panel seal to ensure that it adheres.



c.
B271817

Install the 4 clips.