Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE › 2011.08–2014.07
RM19S0E _59 Vehicle Exterior _051507 EXTERIOR PANELS / TRIM _0248437 NAME PLATE A

EXTERIOR PANELS / TRIM  NAME PLATE  INSTALLATION  


PROCEDURE

Hide 75442 1.INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the back door panel.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 2 luggage compartment door name plate as shown in the illustration.

B283006E07
6,0.979 6.208,1.146 0.208,0.167 10 true *2 4.698,0.979 4.906,1.146 0.208,0.167 10 true *1 5.656,1.906 5.896,2.063 0.24,0.156 10 true *3

Installation Position:
Mark Measurement (along surface)
*1 223.8 mm (8.81 in.)
*2 211.9 mm (8.34 in.)
*3 167.1 mm (6.58 in.)


NOTICE:

Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.



Hide 75446A 2.INSTALL NO. 6 BACK DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the back door panel.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 6 back door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 6 back door name plate as shown in the illustration.

B283005E04
4.688,1.031 4.896,1.208 0.208,0.177 10 true *1 5.813,2.594 6.021,2.771 0.208,0.177 10 true *2 4.76,1.875 4.969,2.052 0.208,0.177 10 true *3

Installation Position:
Mark Measurement (along surface)
*1 215.8 mm (8.50 in.)
*2 220.0 mm (8.66 in.)
*3 51.5 mm (2.03 in.)


NOTICE:

Install the No. 6 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 6 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 6 back door name plate.



Hide 75741E 3.INSTALL SYMBOL EMBLEM

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the back door panel.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the remaining double-sided tape off the back door panel while it is hot from the infrared light.

NOTICE:

Installing the symbol emblem with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B283004E01
2.825,3.587 3.017,3.753 0.192,0.166 10 *1 2.407,3.558 2.775,3.666 false 0.436,3.174 0.628,3.340 0.192,0.166 10 *1 0.624,3.272 0.992,3.38 false

Insert the 2 pins into the back door panel and install a new symbol emblem.

Text in Illustration
*1 Location Pin

NOTICE:

Install the symbol emblem in an environment where the ambient temperature is over 20 °C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the symbol emblem to 20 to 30°C (68 to 86°F) and install the symbol emblem.