Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE › 2014.07–2017.01
RM19S0E _59 Vehicle Exterior _051507 EXTERIOR PANELS / TRIM _0248437 NAME PLATE A

EXTERIOR PANELS / TRIM  NAME PLATE  INSTALLATION  


PROCEDURE

Hide 75442 1.INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the back door panel.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot back door panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 2 luggage compartment door name plate as shown in the illustration.

B377665E02
4.563,0.917 4.75,1.094 0.188,0.177 10 true *1 6.198,0.75 6.385,0.927 0.188,0.177 10 true *2 5.542,2.177 5.729,2.354 0.188,0.177 10 true *3

Installation Position:
Mark Measurement (along surface)
*1 256.3 mm (10.1 in.)
*2 243.3 mm (9.58 in.)
*3 164.9 mm (6.49 in.)


NOTICE:

Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.



Hide 75446A 2.INSTALL NO. 6 BACK DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the back door panel.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot back door panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 6 back door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 6 back door name plate as shown in the illustration.

B377666E02
4.74,0.771 4.927,0.938 0.188,0.167 10 true *1 6.219,0.813 6.406,0.979 0.188,0.167 10 true *2 5.292,2.01 5.479,2.177 0.188,0.167 10 true *3

Installation Position:
Mark Measurement (along surface)
*1 245.7 mm (9.67 in.)
*2 250.8 mm (9.87 in.)
*3 163.6 mm (6.44 in.)


NOTICE:

Install the No. 6 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 6 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 6 back door name plate.



Hide 75741E 3.INSTALL SYMBOL EMBLEM

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the back door panel.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot back door panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the remaining double-sided tape off the back door panel while it is hot from the infrared light.

NOTICE:

Installing the symbol emblem with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B377667E02
1.01,3.448 0.625,3.448 false 2.833,3.594 2.458,3.594 false 0.427,3.354 0.604,3.552 0.177,0.198 10 false *a 2.865,3.5 3.042,3.698 0.177,0.198 10 false *a

Insert the 2 pins into the back door panel and install a new symbol emblem.

Text in Illustration
*a Location Pin

NOTICE:

Install the symbol emblem in an environment where the ambient temperature is over 20 °C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the symbol emblem to 20 to 30°C (68 to 86°F) and install the symbol emblem.