Home › Drivetrain › U340E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2016.09
RM19S0E _52 Drivetrain _051465 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0248156 AUTOMATIC TRANSAXLE SYSTEM C

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input to the ECM.

The sensor resistance changes with the transmission fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies a voltage to the temperature sensor through ECM terminal THO1, and the ECM calculates the fluid temperature based on the voltage signal.

HINT:
·

The ATF temperature is likely to increase under conditions such as towing, climbing hills and in heavy traffic.

·

When the ATF temperature sensor is normal, the transmission locks up in 4th gear with the shift lever in D and in 3rd gear with the shift lever in 3rd.



DTC No. DTC Detection Condition Trouble Area
P0712 ATF temperature sensor resistance is less than 79 Ω for 0.5 seconds or more (1 trip detection logic).
·

Wire harness or connector

·

Transmission wire (ATF temperature sensor)

·

ECM


P0713 Following condition continues for 0.5 seconds or more (1 trip detection logic)
ATF temperature sensor resistance is more than 156 kΩ after 15 minutes or more after start engine.
·

Wire harness or connector

·

Transmission wire (ATF temperature sensor)

·

ECM



MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects opens or shorts in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or wiring. The ECM turns on the MIL and stores the DTC.

*1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.

*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:

The ATF temperature can be checked in the Data List.


WIRING DIAGRAM

C361148E01
1.167,0.979 2.344,1.417 1.177,0.438 10 false ATF Temperature Sensor 2.385,0.604 2.844,0.802 0.458,0.198 10 false THO 2.49,1.604 2.802,1.802 0.313,0.198 10 false E2 2.844,0.583 3,0.781 0.156,0.198 10 false 1 2.833,1.625 2.99,1.823 0.156,0.198 10 false 6 0.938,2.177 1.396,2.375 0.458,0.198 10 false B74 0.917,2.344 3.521,2.542 2.604,0.198 10 false Transmission Wire 5.833,2.25 6.292,2.448 0.458,0.198 10 false B89 5.844,2.438 6.302,2.635 0.458,0.198 10 false ECM 5.75,0.698 6.365,0.896 0.615,0.198 10 false THO1 5.76,1.771 6.375,1.969 0.615,0.198 10 false ETHO 5.417,0.573 5.729,0.771 0.313,0.198 10 false 95 5.417,1.604 5.729,1.802 0.313,0.198 10 false 96

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.


g.

According to the display on the GTS, read the Data List.

Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 ATF Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
·

Approximately 80°C (176°F): After Stall Test

·

Equal to ambient temperature when cold soak


If value is -40°C (-40°F) or 150°C (302°F) or more, ATF temperature sensor circuit is open or short.

HINT:

When DTC P0712 is output and the GTS reading is 150°C (302°F) or more, there is a short circuit.

When DTC P0713 is output and the GTS reading is -40°C (-40°F), there is an open circuit.

Measure the resistance between terminal THO1 and the body ground.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or more Short circuit


HINT:

If a circuit related to the ATF (Automatic Transmission Fluid) temperature sensor becomes open, P0713 is immediately set (within 0.5 seconds).




PROCEDURE

1.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)
C229166E24
2.302,0.948 2.677,0.771 false 2.271,1.24 2.656,1.594 false 2.719,0.688 3.115,0.844 0.396,0.156 10 false THO 2.719,1.531 2.948,1.688 0.229,0.156 10 false E2 0.063,0.031 0.26,0.198 0.198,0.167 10 false *a

a.

Disconnect the B74 transmission wire connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (THO) - 6 (E2) Always 79 Ω to 156 kΩ
1 (THO) - Body ground Always 10 kΩ or higher
6 (E2) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Wire)

HINT:

If the resistance is outside the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may be affected.


Standard Resistance:
ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ




OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
C361141E02
1.75,1.167 1.083,1.75 true 1.792,1.167 2.375,1.792 true 1.542,0.219 2,0.417 0.458,0.198 10 false B89 0.823,1.885 1.438,2.083 0.615,0.198 10 false THO1 2.271,1.865 2.885,2.063 0.615,0.198 10 false ETHO 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a

a.

Connect the B74 transmission wire connector to the transaxle.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B89-95 (THO1) - B89-96 (ETHO) Always 79 Ω to 156 kΩ
B89-95 (THO1) - Body ground Always 10 kΩ or higher
B89-96 (ETHO) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR