Home › Drivetrain › U340E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2016.09
RM19S0E _52 Drivetrain _051465 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0248156 AUTOMATIC TRANSAXLE SYSTEM C

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0973  Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1)  P0974  Shift Solenoid "A" Control Circuit High (Shift Solenoid Valve S1)  


DESCRIPTION

Shifting from 1st to 4th is performed in combination with the ON and OFF operations of shift solenoid valves S1 and S2 which are controlled by the ECM. If an open or short circuit occurs in either of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valve to allow the vehicle to be driven smoothly.

(If an open or short circuit occurs, the ECM stops sending current to the affected circuit.)

Fail-safe function (See page Drivetrain>U340E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).

DTC No. DTC Detection Condition Trouble Area
P0973 ECM detects short in solenoid valve S1 circuit 4 times when solenoid valve S1 is operated (1 trip detection logic).
·

Wire harness or connector

·

Transmission wire

·

Shift solenoid valve S1

·

ECM


P0974 ECM detects open in solenoid valve S1 circuit 4 times when solenoid valve S1 is not operated (1 trip detection logic).
·

Wire harness or connector

·

Transmission wire

·

Shift solenoid valve S1

·

ECM



MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in the shift solenoid valve S1 circuit, the ECM detects the problem and the MIL comes on. Illuminating the MIL, the ECM performs the fail-safe and turns the other functioning shift solenoid valve ON/OFF.

(If an open or short circuit occurs, the ECM stops sending current to the affected circuit.)

WIRING DIAGRAM

C361150E02
1,2.177 3.604,2.375 2.604,0.198 10 false Transmission Wire 1,2 1.458,2.198 0.458,0.198 10 false B74 1.177,1.385 2.229,1.813 1.052,0.427 10 false Shift Solenoid Valve S1 2.271,0.948 2.583,1.146 0.313,0.198 10 false S1 2.594,0.948 2.75,1.146 0.156,0.198 10 false 5 5.833,1.052 6.146,1.25 0.313,0.198 10 false S1 5.51,0.948 5.823,1.146 0.313,0.198 10 false 70 5.917,2.167 6.375,2.365 0.458,0.198 10 false B89 5.917,2.344 6.375,2.542 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Shift solenoid valve S1 is turned on/off normally when the shift lever is in D:

Gearshift controlled by ECM 1st 2nd 3rd 4th
Shift solenoid valve S1 ON ON OFF OFF


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S1)
C229166E12
0.196,0.601 0.397,0.759 0.201,0.158 10 S1 1.139,0.982 0.441,0.696 false 0.059,0.059 0.256,0.223 0.197,0.164 10 *a

a.

Disconnect the B74 transmission wire connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (S1) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE S1
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
C361141E05
1.083,1.104 0.75,1.833 true 0.094,0.094 0.354,0.292 0.26,0.198 10 false *a 1.573,0.219 2.031,0.417 0.458,0.198 10 false B89 0.615,1.885 0.927,2.083 0.313,0.198 10 false S1

a.

Connect the B74 transmission wire connector to the transaxle.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B89-70 (S1) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR