Home › Drivetrain › U340E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2016.09
RM19S0E _52 Drivetrain _051465 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0248156 AUTOMATIC TRANSAXLE SYSTEM C

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2769  Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)  P2770  Open in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)  


DESCRIPTION

Shift solenoid valve SL is turned ON and OFF by signals from the ECM to control the hydraulic pressure in the lock-up relay valve, which then controls the operation of the lock-up clutch.

Fail-safe function:

·

If the ECM detects a malfunction, it turns shift solenoid valve SL OFF.


·

The system cannot control the lock-up relay valve. (No relation to 3-4 shift control)


DTC No. DTC Detection Condition Trouble Area
P2769 ECM detects short in solenoid valve SL circuit when solenoid valve SL operated. (Solenoid resistance: 8 Ω or less)
(2 trip detection logic)
·

Wire harness or connector

·

Transmission wire

·

Shift solenoid valve SL

·

ECM


P2770 ECM detects open in solenoid valve SL circuit when solenoid valve SL not operated. (Solenoid resistance: 100 kΩ or more)
(2 trip detection logic)
·

Wire harness or connector

·

Transmission wire

·

Shift solenoid valve SL

·

ECM



MONITOR DESCRIPTION

Based on the signals from the throttle position sensor, the mass air flow meter and the crankshaft position sensor, the ECM sends a signal to shift solenoid valve SL to regulate the hydraulic pressure and provide smoother gearshifting. Shift solenoid valve SL responds to the signals from the ECM. The valve controls the lock-up relay valve to perform the torque converter lock-up function. If the ECM detects an open or short circuit of shift solenoid valve SL, it illuminates the MIL and sets a DTC.

WIRING DIAGRAM

C361150E04
1.083,2.021 1.542,2.219 0.458,0.198 10 false B74 1.083,2.198 3.688,2.396 2.604,0.198 10 false Transmission Wire 1.156,1.406 2.094,1.75 0.938,0.344 10 false Shift Solenoid Valve SL 2.24,0.948 2.552,1.146 0.313,0.198 10 false SL 2.583,0.948 2.74,1.146 0.156,0.198 10 false 4 5.5,0.948 5.813,1.146 0.313,0.198 10 false 68 5.833,1.083 6.146,1.281 0.313,0.198 10 false SL 5.917,2.177 6.375,2.375 0.458,0.198 10 false B89 5.917,2.385 6.375,2.583 0.458,0.198 10 false ECM

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)
a.
C229166E17
1.012,1.782 1.233,1.943 0.221,0.161 10 SL 1.413,1.015 1.148,1.745 false 0.059,0.028 0.256,0.192 0.197,0.164 10 *a

Disconnect the B74 transmission wire connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SL) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C361141E08
0.958,1.094 0.583,1.833 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.552,0.229 2.01,0.427 0.458,0.198 10 false B89 0.448,1.885 0.76,2.083 0.313,0.198 10 false SL

Connect the B74 transmission wire connector to the transaxle.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B89-68 (SL) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR