Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › IGNITION SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248055 IGNITION SYSTEM G

2NZ-FE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.PERFORM SPARK TEST

HINT:

Perform "Inspection After Repair" after replacing a No. 1 ignition coil or spark plug.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Check for DTCs.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.



b.

Remove the 4 No. 1 ignition coils and 4 spark plugs.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL

NOTICE:

If the No. 1 ignition coil or spark plug has been struck or dropped, replace it.


HINT:

Arrange the removed parts in the correct order.



c.
A156076

Disconnect the 4 injector connectors.

NOTICE:

Perform this step in order to stop fuel injection to prevent damage to the catalyst due to unburned fuel.



d.
A156093

Install a spark plug to each No. 1 ignition coil and connect the No. 1 ignition coil connectors.


e.

Ground the spark plugs.


f.

Check that spark occurs while the engine is being cranked.


g.

Check whether sparks occur.

NOTICE:
·

Ground the spark plugs when checking them.

·

Replace any ignition coils that have been subjected to a physical impact.

·

Do not crank the engine for more than 2 seconds.

·

If the spark plug is struck or dropped, replace it.




h.

If spark does not occur, perform the following procedure.


i.

Install the 4 spark plugs and 4 No. 1 ignition coils.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION

NOTICE:

If a No. 1 ignition coil or spark plug has been struck or dropped, replace it.


HINT:

Install the same parts to their original positions.





Hide 2.INSPECT IGNITION COIL AND SPARK TEST

HINT:

Perform "Inspection After Repair" after replacing a No. 1 ignition coil or spark plug.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Perform the spark test in accordance with the following procedure.

i.

Check that the wire harness side connector of the No. 1 ignition coil is securely connected.

Result:
Result Proceed to
NG Connect securely
OK Go to next step



b.

Perform a spark test on each No. 1 ignition coil.

i.

If there is a cylinder where sparks do not occur, replace its No. 1 ignition coil with the No. 1 ignition coil of a cylinder where sparks occur normally.


ii.

Crank the engine and visually check that sparks occur at the cylinder with the normally operating No. 1 ignition coil.

Result:
Result Proceed to
NG Replace No. 1 ignition coil
(Click here)
OK Go to next step

NOTICE:

If a No. 1 ignition coil or spark plug has been struck or dropped, replace it.




c.

Perform a spark test on each spark plug.

i.

If there is a cylinder where sparks do not occur, replace its spark plug with the spark plug of a cylinder where sparks occur normally.


ii.

Crank the engine and visually check that sparks occur at the cylinder with the normally operating spark plug.

Result:
Result Proceed to
NG Replace spark plug
(Click here)
OK Ignition Circuit
(Click here)

NOTICE:

If a No. 1 ignition coil or spark plug has been struck or dropped, replace it.




d.

Connect the 4 injector connectors.


e.

Install the No. 1 ignition coil and spark plug.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION

NOTICE:

If a No. 1 ignition coil or spark plug has been struck or dropped, replace it.


HINT:

Install the same parts to their original positions.





Hide 19100P 3.INSPECT SPARK PLUG

NOTICE:
·

Be careful not to damage the iridium tip or platinum tip of the spark plug.

·

Check the iridium tip visually as it is easily damaged.

·

Never attempt to adjust the electrode gap of a used spark plug.

·

If the spark plug is extremely dirty with oil, etc., replace it.

·

Replace a spark plug if it is damaged at all.

·

When installing a new spark plug, do not remove the protective cap from the spark plug tip until just before installing the spark plug to the engine.

·

If the spark plug has been struck or dropped, replace it.



HINT:

Perform "Inspection After Repair" after replacing a spark plug.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A381813C02
1.083,1.896 0.823,1.896 false 0.604,1.823 0.844,2.031 0.24,0.208 10 false *1
*1 Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (Terminal part) - Ground Always 10 MΩ or higher


HINT:

If a megohmmeter is not available, perform the following simple inspection instead.




b.

Alternative inspection method:

i.

Start the engine.


ii.

Quickly accelerate the engine to 4000 rpm 5 times.

NOTICE:

When DTC P0300 (Random / Multiple Cylinder Misfire Detected) or related DTCs are output, do not perform this step.




iv.
A126881

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage to its thread and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Product
DENSO SK16R11
NGK IFR5A11



d.
A126880C15
0.708,1.115 1.042,1.396 0.333,0.281 10 *a
*a Electrode Gap


Check the spark plug electrode gap.

Maximum electrode gap for used spark plug:

1.3 mm (0.051 in.)


If the gap is greater than the maximum, replace the spark plug.

Electrode gap for new spark plug:

1.0 to 1.1 mm (0.039 to 0.043 in.)


NOTICE:

Never attempt to adjust the electrode gap of a used spark plug.




Hide 4.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a No. 1 ignition coil or spark plug.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION