Home › General › SPECIFICATIONS › 2NZ-FE ENGINE CONTROL › from 2016.09
RM19S0E _V1 General _051446 SPECIFICATIONS _0247979 2NZ-FE ENGINE CONTROL F

SPECIFICATIONS  2NZ-FE ENGINE CONTROL  SERVICE DATA  


Spark plug insulation standard resistance - 10 MΩ or more
Spark plug electrode gap For new spark plug 1.0 to 1.1 mm (0.039 to 0.043 in.)
Spark plug maximum electrode gap For used spark plug 1.3 mm (0.051 in.)
Camshaft timing oil control valve standard resistance 1 - 2 6.9 to 7.9 Ω at 20 °C (68°F)
Throttle body standard resistance 1 (M-) - 2 (M+) 0.3 to 100 Ω at 20 °C (68°F)
Accel sensor out No. 1 standard voltage Accelerator pedal is released 0.5 to 1.1 V
Accelerator pedal is fully depressed 2.6 to 4.5 V
Accel sensor out No. 2 standard voltage Accelerator pedal is released 1.2 to 2.0 V
Accelerator pedal is fully depressed 3.4 to 4.7 V
Mass air flow meter standard resistance 1 (THA) - 2 (E2) 13.6 to 18.4 kΩ at -20°C (-4°F)
2.21 to 2.69 kΩ at 20°C (68°F)
0.49 to 0.67 kΩ at 60°C (140°F)
MAF
·

Engine not running

·

30 seconds after ignition switch is turned to ON


0.28 gm/sec or less
Camshaft position sensor standard resistance 1 - 2 1630 to 2740 Ω at cold
2065 to 3225 Ω at hot
Crankshaft position sensor standard resistance 1 - 2 985 to 1600 Ω at cold
1265 to 1890 Ω at hot
Engine coolant temperature sensor standard resistance 1 - 2 2.32 to 2.59 kΩ at 20°C (68°F)
0.310 to 0.326 kΩ at 80°C (176°F)
Knock sensor standard resistance 1 - 2 120 to 280 kΩ at 20 °C (68°F)
Air fuel ratio sensor standard resistance 1 (HT1A) - 2 (+B) 1.6 to 3.2 Ω at 20°C (68°F)
1 (HA1A) - 4 (A1A-) 10 kΩ or higher
Heated oxygen sensor standard resistance 1 (HT1B) - 2 (+B) 9 to 14 Ω at 20°C (68°F)
1 (HT1B) - 4 (E2) 10 kΩ or higher
Integration relay (EFI MAIN relay) resistance 1C-1 - 1E-4 10 kΩ or higher
(Battery voltage not applied between 1E-10 - 1D-7 terminals)
Below 1 Ω
(Battery voltage applied between 1E-10 - 1D-7 terminals)
Integration relay (C/OPN relay) resistance 1E-4 - 1E-5 10 kΩ or higher
(Battery voltage not applied between 1E-11 - 1D-9 terminals)
Below 1 Ω
(Battery voltage applied between 1E-11 - 1D-9 terminals)
Integration relay (IG2 relay) resistance 1C-1 - 1D-9 10 kΩ or higher
(Battery voltage not applied between 1E-10 - 1D-17 terminals)
Below 1 Ω
(Battery voltage applied between 1E-10 - 1D-17 terminals)
Integration relay (HORN relay) resistance 1C-1 - 1E-7 10 kΩ or higher
(Battery voltage not applied between 1C-1 - 1D-18 terminals)
Below 1 Ω
(Battery voltage applied between 1C-1 - 1D-18 terminals)