Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY(for Front Passenger Side) › from 2016.09
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248323 FRONT SEAT SIDE AIRBAG ASSEMBLY(for Front Passenger Side) A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT SEAT SIDE AIRBAG ASSEMBLY(for Front Passenger Side)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>PRECAUTION).

·

If the side airbag was deployed, replace the front seat airbag assembly, separate type front seatback spring assembly, separate type front seatback cover and separate type front seatback pad with a new one.

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:

Always use "TORX" socket wrench E10 when removing the front seat.


PROCEDURE

Hide 73920A 1.INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
·

The nuts must not be reused.

·

Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.



a.

Install the front seat side airbag assembly with 2 new nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Engage the 2 clamps.


c.

Engage the 7 clamps to install the front seat side airbag wire harness.


Hide 2.INSTALL FRONT SEATBACK COVER WITH PAD

a.

Temporary install the front seatback cover with pad.


b.

Install the front seatback cover bracket with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:
·

For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.

·

Check that the strap is not twisted after installing the bracket.

·

Install the bracket securely.




c.

Fasten the 2 zippers. (for Sport Package)


d.
B272765E01
0.989,0.726 1.594,0.362 false 3.007,1.121 2.402,0.757 false 1.607,0.254 1.789,0.436 0.182,0.182 10 *a 2.219,0.647 2.401,0.829 0.182,0.182 10 *a

Align the protruding portion of the front seat headrest support with the installation groove of the front seat adjuster frame.

Text in Illustration
*a Protruding


e.

Engage the 4 claws to install the 2 front seat headrest supports.


f.
B287798E01
0.551,3.137 0.407,2.95 false 0.236,2.85 0.406,3.006 0.170,0.156 10 *1 1.952,4.411 1.809,4.224 false 1.892,4.415 2.062,4.571 0.170,0.156 10 *2

Using hog ring pliers, install 3 new hog rings.

Text in Illustration
*1 New Hog Ring
*2 Hog Ring Pliers


g.
B289867E01
0.549,3.136 0.395,2.971 false 0.21,2.894 0.370,3.047 0.160,0.153 10 *1 1.967,4.384 1.813,4.219 false 1.874,4.376 2.034,4.529 0.160,0.153 10 *2

Using hog ring pliers, install 3 new hog rings.

Text in Illustration
*1 New Hog Ring
*2 Hog Ring Pliers

NOTICE:

Do not soil or scratch the front seatback cover.



h.

Fasten the hook and loop fastener.


i.

Connect the seatback cover band.


Hide 3.INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY (for 3 Door)

HINT:

Use the same procedure as for the LHD (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Front Passenger Side)>REASSEMBLY).


Hide 71862 4.INSTALL FRONT SEAT CUSHION INNER SHIELD

HINT:

Use the same procedure as for the LHD (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Front Passenger Side)>REASSEMBLY).


Hide 71812D 5.INSTALL FRONT SEAT CUSHION SHIELD

HINT:

Use the same procedure as for the LHD (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Front Passenger Side)>REASSEMBLY).


Hide 72526A 6.INSTALL RECLINING ADJUSTER RELEASE HANDLE

HINT:

Use the same procedure as for the LHD (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Front Passenger Side)>REASSEMBLY).


Hide 71910A 7.INSTALL FRONT SEAT HEADREST ASSEMBLY

HINT:

Use the same procedure as for the LHD (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Front Passenger Side)>REASSEMBLY).


Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.5 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION