DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in P or neutral, the A/C switch should be off and all accessory switches should be off.
Warm up the engine.
Turn the A/C switch off.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
When you select a measurement group, the ECU data belonging to that group is displayed.
Measurement Group List / Description
All Data / All data
Primary / -
Engine Control / Engine control system related data
Ptrl General / -
Ptrl AF Control / Air-fuel ratio control system related data
Ptrl AF O2 Sensor / Air fuel ratio sensor and heated oxygen sensor related data
Ptrl Throttle / Gasoline throttle system related data
Ptrl Intake Control / Intake control system related data
Ptrl Valve Control / Valve control system related data
Ptrl Misfire / "Misfire" related data
Ptrl Starting / "Difficult to start" related data
Ptrl Rough Idle / "Rough idle" related data
Ptrl Evaporative / Evaporative system related data
Ptrl CAT Converter / Catalytic converter related data
Check Mode / Check mode related data
Monitor Status / Monitor status related data
Ignition / Ignition system related data
Charging Control / Charging control system related data
Compression / Data used during "Check the Cylinder Compression" Active Test
AT / Automatic transaxle system related data
Vehicle Information / Vehicle information
According to the display on the GTS, read the Data List.
The title used for each group of Data List items in this repair manual does not appear on the GTS. However, the name in parentheses after the title, which is a Measurement Group, does appear on the GTS. When the name shown in parentheses is selected on the GTS, all the Data List items listed for that group will be displayed.
"Result of real-vehicle check" is the assessment of one vehicle. Use it only for reference.
Various Vehicle Conditions 1 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Vehicle Speed | Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h |
Actual vehicle speed | Yes |
| Diagnostic Note:
·
This is the current vehicle speed ·
The vehicle speed is detected using the wheel speed sensors. Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Speed | Engine speed/
Min.: 0 rpm, Max.: 16383 rpm |
650 to 750 rpm: Idling (AT)
600 to 700 rpm: Idling (MT) |
Yes |
| Results of real-vehicle check:
Idling (warm up the engine, A/C off): 704 rpm (for Automatic Transaxle) |
|||
| Diagnostic Note:
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Calculate Load | Load calculated by ECM/
Min.: 0%, Max.: 100% |
- | Yes |
| Results of real-vehicle check:
·
Ignition switch ON: 0.0% ·
Idling (warm up the engine): 30.5% ·
Running without load (3000 rpm): 21.9% |
|||
| Diagnostic Note:
This is the engine load calculated based on the estimated intake manifold pressure. Calculate Load = Estimated intake manifold pressure / maximum intake manifold pressure x 100 (%) (For example, when the estimated intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.) |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Vehicle Load | Vehicle load/
Min.: 0%, Max.: 25700% |
- | Yes |
| Results of real-vehicle check:
·
Ignition switch ON: 0.0% ·
Idling (warm up the engine): 20.3% ·
Running without load (3000 rpm): 16.8% |
|||
| Diagnostic Note:
This is the engine intake air charging efficiency. Vehicle Load = Current intake airflow (g/rev.) / maximum intake airflow Maximum intake airflow = Displacement (L) / 2 x 1.2 (g/rev.)
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| MAF | Airflow rate from Mass Air Flow (MAF) meter/
Min.: 0 gm/sec, Max.: 655 gm/sec |
1.0 to 3.0 gm/sec: Idling
3.0 to 7.0 gm/sec: 2500 rpm (without load) 4.0 to 8.0 gm/sec: 3000 rpm (without load) |
Yes |
| Results of real-vehicle check:
·
Ignition switch ON: 0.20 gm/sec ·
Idling (warm up the engine): 1.84 gm/sec ·
Running without load (2500 rpm): 5.68 gm/sec ·
Running without load (3000 rpm): 6.59 gm/sec |
|||
| Diagnostic Note:
This is the intake air amount from the mass air flow meter. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Atmosphere Pressure | Atmospheric pressure/
Min.: 0 kPa (0 mmhg), Max.: 255 kPa (1912 mmhg) |
Equivalent to the atmosphere pressure (absolute pressure) | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): 103 kPa |
|||
| Diagnostic Note:
·
This value is calculated from the intake air amount. ·
Standard atmospheric pressure: 101 kPa ·
For every 100 m increase in altitude, pressure drops by 1 kPa. This varies by weather. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Coolant Temp | Coolant temperature/
Min.: -40°C, Max.: 215°C |
80 to 100°C (176 to 212°F): After warming up | Yes |
| Diagnostic Note:
This is the engine coolant temperature.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Intake Air | Intake air temperature/
Min.: -40°C, Max.: 140°C |
Equivalent to temperature at location of mass air flow meter | Yes |
| Diagnostic Note:
·
After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal. ·
If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Ambient Temperature | Ambient temperature/
Min.: -40°C, Max.: 215°C |
Equivalent to ambient air temperature | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Run Time | Engine run time/
Min.: 0 s, Max.: 65535 s |
Time after engine start | Yes |
| Diagnostic Note:
This is the time elapsed since the engine started.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Initial Engine Coolant Temp | Initial engine coolant temperature/
Min.: -40°C, Max.: 119°C |
- | Yes |
| Diagnostic Note:
This is the coolant temperature stored when the ignition switch is turned to ON. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Initial Intake Air Temp | Initial intake air temperature/
Min.: -40°C, Max.: 119°C |
- | Yes |
| Diagnostic Note:
This is the intake air temperature stored when the ignition switch is turned to ON. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Battery Voltage | Battery voltage/
Min.: 0 V, Max.: 66 V |
11 to 14 V: Idling | Yes |
| Results of real-vehicle check:
·
Ignition switch ON: 12.089 V ·
Cranking: 11.015 V ·
Idling (warm up the engine): 13.398 V |
|||
| Diagnostic Note:
If 11 V or less, characteristics of some electrical components may change. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Glow Indicator Supported | Status of the glow indicator supported (for Automatic Transaxle)/
Unsupp or Supp |
Unsupp | Yes |
| Diagnostic Note:
This item is displayed only for Automatic Transaxle. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Glow Indicator | Status of the glow indicator supported (for Automatic Transaxle)/
ON or OFF |
OFF | Yes |
| Diagnostic Note:
This item is displayed only for Automatic Transaxle. |
|||
Throttle Control 1 (Ptrl Throttle)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accelerator Position | Accelerator pedal position/
Min.: 0%, Max.: 399.9% |
Actual accelerator pedal position | No |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 0.0% ·
Ignition switch ON (accelerator pedal fully depressed): 100.0% |
|||
| Diagnostic Note:
This is the accelerator pedal position defined using the learned fully released position (sensor output) of accelerator pedal position sensor No. 1 as 0% and the fully depressed position as 100%. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accel Sens. No.1 Volt % | Absolute Accelerator Pedal Position (APP) No. 1/
Min.: 0%, Max.: 100% |
10 to 22%: Accelerator pedal released
52 to 90%: Accelerator pedal fully depressed |
Yes |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 16.0% ·
Ignition switch ON (accelerator pedal fully depressed): 69.4% |
|||
| Diagnostic Note:
The accelerator pedal position sensor No. 1 output is converted using 5 V = 100%.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accel Sens. No.2 Volt % | Absolute APP No. 2/
Min.: 0%, Max.: 100% |
24 to 40%: Accelerator pedal released
68 to 100%: Accelerator pedal fully depressed |
Yes |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 31.7% ·
Ignition switch ON (accelerator pedal fully depressed): 85.0% |
|||
| Diagnostic Note:
The accelerator pedal position sensor No. 2 output is converted using 5 V = 100%. |
|||
Throttle Control 2 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accel Sensor Out No.1 | APP sensor No. 1 voltage/
Min.: 0 V, Max.: 4.98 V |
0.5 to 1.1 V: Accelerator pedal released
2.6 to 4.5 V: Accelerator pedal fully depressed |
No |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 0.800 V ·
Ignition switch ON (accelerator pedal fully depressed): 3.457 V |
|||
| Diagnostic Note:
This is the raw voltage from the accelerator pedal position sensor No. 1. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accel Sensor Out No.2 | APP sensor No. 2 voltage/
Min.: 0 V, Max.: 4.98 V |
1.2 to 2.0 V: Accelerator pedal released
3.4 to 4.7 V: Accelerator pedal fully depressed |
No |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 1.582 V ·
Ignition switch ON (accelerator pedal fully depressed): 4.238 V |
|||
| Diagnostic Note:
·
This is the raw voltage from the accelerator pedal position sensor No. 2. ·
Accelerator pedal position sensor No. 2 is used to monitor accelerator pedal position sensor No. 1. When there is a malfunction in sensor No. 1, the ECM uses sensor No. 2 to control the engine. |
|||
Throttle Control 3 (Ptrl Throttle)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting released accelerator pedal/
ON or OFF |
ON: Accelerator pedal released | No |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): ON ·
Ignition switch ON (accelerator pedal fully depressed): OFF |
|||
| Diagnostic Note:
This is a parameter calculated by the ECM which indicates whether the accelerator pedal is in the learned idle position. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accel Fully Close Learn #1 | Accelerator fully released learned value No. 1/
Min.: 0 deg, Max.: 124.5 deg |
- | No |
| Results of real-vehicle check:
Ignition switch ON: 20.0 deg |
|||
| Diagnostic Note:
This is the value of accelerator pedal position sensor No. 1 learned when the accelerator pedal is released. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accel Fully Close Learn #2 | Accelerator fully released learned value No. 2/
Min.: 0 deg, Max.: 124.5 deg |
- | No |
| Results of real-vehicle check:
Ignition switch ON: 39.5 deg |
|||
| Diagnostic Note:
This is the value of accelerator pedal position sensor No. 2 learned when the accelerator pedal is released. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Sensor Volt % | Absolute throttle position sensor/
Min.: 0%, Max.: 100% |
·
10 to 22%: Throttle fully closed ·
64 to 96%: Throttle fully open |
Yes |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 18.8% ·
Ignition switch ON (accelerator pedal fully depressed): 81.1% ·
Idling (warm up the engine): 15.2% ·
Running without load (3000 rpm): 19.2% |
|||
| Diagnostic Note:
The throttle position sensor No. 1 output is converted using 5 V = 100%.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttl Sensor #2 Volt % | Throttle sensor position #2/
Min.: 0%, Max.: 100% |
·
42 to 62%: Throttle fully closed ·
92 to 100%: Throttle fully open |
Yes |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 50.9% ·
Ignition switch ON (accelerator pedal fully depressed): 99.6% ·
Idling (warm up the engine): 46.6% |
|||
| Diagnostic Note:
The throttle position sensor No. 2 output is converted using 5 V = 100%. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| ST1 | Brake pedal signal/
ON or OFF |
ON: Brake pedal depressed
OFF: Brake pedal released |
No |
| Diagnostic Note:
This is the brake pedal switch signal (ST1 - terminal signal). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| System Guard | System guard/
ON or OFF |
ON | No |
| Results of real-vehicle check:
Idling (warm up the engine): ON |
|||
| Diagnostic Note:
When there is a difference between the target and actual throttle valve opening angles, system guard turns off and stops the electronic throttle control system function. OFF: Electronic throttle control is stopped. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Open Side Malfunction | Open malfunction/
ON or OFF |
OFF | No |
| Diagnostic Note:
This parameter indicates a malfunction in the electronic throttle when the throttle valve is open. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Idle Position | Whether or not throttle position sensor detecting idle/
ON or OFF |
- | No |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): ON ·
Ignition switch ON (accelerator pedal fully depressed): OFF ·
Idling (warm up the engine): ON ·
Running without load (3000 rpm): OFF |
|||
| Diagnostic Note:
This is a parameter calculated by the ECM. The value is ON when the throttle is at the idle position and OFF when the throttle is open. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Require Position | Required throttle position/
Min.: 0 V, Max.: 4.98 V |
- | No |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 0.917 V ·
Ignition switch ON (accelerator pedal fully depressed): 4.042 V ·
Idling (warm up the engine): 0.761 V |
|||
| Diagnostic Note:
This is a value calculated by the ECM showing the voltage for the target throttle valve position. It is almost an exact match of the Throttle Position No. 1 value except during very rapid throttle valve movement, such as that used during wheelspin control. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Sensor Position | Throttle sensor position/
Min.: 0%, Max.: 100% |
·
0%: Throttle fully closed ·
50 to 80%: Throttle fully open |
Yes |
| Results of real-vehicle check:
Idling (warm up the engine): 0.0% |
|||
| Diagnostic Note:
This is the throttle valve opening amount used for engine control. (100% signifies 125° of throttle valve rotation. This does not include the amount the throttle valve is opened to maintain the idling speed during idling.) This value has no meaning when the ignition switch is ON and the engine is stopped. The throttle valve opening amount during idling is indicated by 0%. When the throttle valve is fully open, the value is 68%. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.98 V |
Almost same as "Throttle Require Position"
·
0.5 to 1.1 V: Throttle fully closed ·
3.2 to 4.8 V: Throttle fully open ·
0.6 to 1.4 V: Fail-safe operating |
No |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 0.937 V ·
Ignition switch ON (accelerator pedal fully depressed): 4.042 V ·
Idling (warm up the engine): 0.761 V |
|||
| Diagnostic Note:
This is the throttle position sensor No. 1 output voltage. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.98 V |
·
2.1 to 3.1 V: Throttle fully closed ·
4.6 to 5.0 V: Throttle fully open ·
2.1 to 3.1 V: Fail-safe operating |
No |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 2.539 V ·
Ignition switch ON (accelerator pedal fully depressed): 4.960 V ·
Idling (warm up the engine): 2.324 V |
|||
| Diagnostic Note:
This is the throttle position sensor No. 2 output voltage. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Position Command | Throttle position command value/
Min.: 0 V, Max.: 4.98 V |
- | No |
| Diagnostic Note:
Throttle Position Command is the same value as Throttle Require Position. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Sens Open Pos #1 | Throttle position sensor No. 1/
Min.: 0 V, Max.: 4.98 V |
0.6 to 1.4 V | No |
| Results of real-vehicle check:
Ignition switch ON: 0.917 V |
|||
| Diagnostic Note:
This is the throttle position sensor No. 1 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch on. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Sens Open Pos #2 | Throttle position sensor No. 2/
Min.: 0 V, Max.: 4.98 V |
1.7 to 2.5 V | No |
| Results of real-vehicle check:
Ignition switch ON: 2.031 V |
|||
| Diagnostic Note:
This is the throttle position sensor No. 2 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch on. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Motor Current | Throttle actuator current/
Min.: 0 A, Max.: 19.9 A |
0 to 3.0 A: Idling | No |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 0.0 A ·
Ignition switch ON (accelerator pedal fully depressed): 0.9 A ·
Idling (warm up the engine): 0.9 A ·
Running without load (3000 rpm): 0.5 A |
|||
| Diagnostic Note:
·
When this value is large but the actual opening angle (Throttle Position No. 1) does not reach the target opening angle (Throttle Require Position), there is an unable to open malfunction. ·
This value normally fluctuates around 1 A. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Motor DUTY | Throttle actuator/
Min.: 0%, Max.: 100% |
0.5 to 40%: Idling after engine warmed up. | Yes |
| Diagnostic Note:
This is the output duty ratio of the throttle actuator drive circuit. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255% |
0 to 40%: Idling | No |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 0% ·
Ignition switch ON (accelerator pedal fully depressed): 17% ·
Idling (warm up the engine): 0% ·
Running without load (3000 rpm): 9% |
|||
| Diagnostic Note:
·
This is the duty ratio used to drive the throttle actuator and open the throttle valve. It is an ECM command signal. ·
When the throttle valve is being opened, Throttle Motor Duty (Open) is 10 to 50%. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 255% |
0 to 40%: Idling | No |
| Results of real-vehicle check:
·
Ignition switch ON (accelerator pedal released): 0% ·
Ignition switch ON (accelerator pedal fully depressed): 0% ·
Idling (warm up the engine): 11% ·
Running without load (3000 rpm): 0% |
|||
| Diagnostic Note:
This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Fully Close Learn | Throttle valve fully closed (learned value)/
Min.: 0 V, Max.: 4.980 V |
0.4 to 1.0 V: Accelerator pedal released | No |
| Results of real-vehicle check:
Ignition switch ON: 0.683 V |
|||
| Diagnostic Note:
·
The ECM uses this learned value to determine the fully closed (and fully open) position of the throttle valve. This learned value is calculated by the ECM with the throttle valve opener angle (approximately 4 to 7°, the position when the ignition switch is ON, the accelerator pedal is released and the throttle actuator is off). ·
Learning is performed immediately after the ignition switch is turned to ON. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| +BM Voltage | +BM voltage/
Min.: 0 V, Max.: 79.998 V |
11 to 14 V: Ignition switch ON and system normal | No |
| Diagnostic Note:
This is the power supply for the electronic throttle actuator. When the power supply is interrupted for approximately 1 second, DTCs P2118 (open circuit) and P0657 (short circuit, ECU malfunction) are stored and the electronic throttle control system enters fail-safe mode (normal operation is not restored until the ignition switch is turned off). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Actuator Power Supply | Actuator power supply/
ON or OFF |
ON: Idling | No |
| Diagnostic Note:
If +BM power is lost, this item changes to OFF. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Position | Throttle valve opening angle/
Min.: 0 deg, Max.: 500 deg |
- | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): 0.00 deg |
|||
| Diagnostic Note:
This value has no meaning when the ignition switch is ON and the engine is stopped. |
|||
Idle Speed Control (Ptrl Rough Idle)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| ISC Flow | Flow rate calculated using information from MAF (mass air flow meter)/
Min.: 0 L/s, Max.: 80 L/s |
- | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): 1.38 L/s |
|||
| Diagnostic Note:
This is the total ISC airflow amount (the amount of intake air necessary to maintain idling).
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| ISC Position | Requested throttle opening amount calculated using ISC control/
Min.: 0 deg, Max.: 500 deg |
- | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): 1.76 deg |
|||
| Diagnostic Note:
This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| ISC Feedback Value | ISC feedback amount/
Min.: -40 L/s, Max.: 40 L/s |
- | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): -0.03 L/s |
|||
| Diagnostic Note:
This is the feedback amount necessary to adjust the airflow amount to maintain the target idling speed.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| ISC Learning Value | ISC learned airflow value/
Min.: -40 L/s, Max.: 40 L/s |
- | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): 1.35 L/s |
|||
| Diagnostic Note:
This is the learned value of the airflow amount necessary for engine idling.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Electric Load Feedback Val | Compensation flow rate according to electrical load/
Min.: -40 L/s, Max.: 40 L/s |
- | Yes |
| Diagnostic Note:
This is the ISC compensation amount determined according to the electrical load. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Air Conditioner FB Val | Compensation flow rate according to air conditioner load/
Min.: -40 L/s, Max.: 40 L/s |
- | Yes |
| Diagnostic Note:
This is the ISC compensation amount determined according to the air conditioner load. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Low Revolution Control | Low engine speed control operation state/
ON or OFF |
- | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): OFF |
|||
| Diagnostic Note:
·
This parameter indicates whether the engine speed dropped immediately after starting due to poor combustion, etc. This parameter changes to ON when the engine speed drops to below the following speeds 1 to 7 seconds after the engine is started (when the A/C is on, the engine speed thresholds below increase by 100 to 200 rpm). -
900 rpm (when the engine coolant temperature is 10°C (50°F) -
850 rpm (when the engine coolant temperature is 30°C (86°F) -
750 rpm (when the engine coolant temperature is 60°C (140°F) Before 5 seconds elapse after starting the engine, this parameter indicates the status of the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the status of the current trip.
·
For use when engine stall, starting problems or rough idle is present. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Neutral Control | Neutral control status/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| N Range Status | Shift lever N status/
ON or OFF |
- | Yes |
| Diagnostic Note:
This item is displayed only for Automatic Transaxle. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Eng Stall Control FB Flow | Intake air compensation flow rate/
Min.: -40 L/s, Max.: 40 L/s |
- | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): 0.00 L/s |
|||
| Diagnostic Note:
·
The intake air amount and ignition timing are adjusted when there is a large decrease in engine speed (for example, a decrease to 550 rpm or less) in order to prevent engine stall. ·
For use when engine stall, starting problems or rough idle is present. |
|||
Fuel System (Ptrl General)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injector (Port) | Injection period of the No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs |
- | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): 2541 μs ·
Running without load (3000 rpm): 2053 μs |
|||
| Diagnostic Note:
This is the injection period of the No. 1 cylinder (the command value from the ECM). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml |
0 to 0.15 ml: Idling, engine warmed up | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): 0.068 ml ·
Running without load (3000 rpm): 0.052 ml |
|||
| Diagnostic Note:
This is the fuel injection volume for 10 injections. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel Pump/Speed Status | Fuel pump status/
ON or OFF |
ON: Starter on or engine running | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Current Fuel Type | Current fuel type | Gasoline/petrol | Yes |
EVAP System (Ptrl Evaporative)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| EVAP (Purge) VSV | Purge VSV control duty/
Min.: 0%, Max.: 100% |
- | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): 0.0% ·
Running without load (3000 rpm): 65.0% |
|||
| Diagnostic Note:
·
This is the command signal from the ECM. ·
This is the purge VSV control duty ratio. When EVAP (Purge) VSV is any value except 0%, EVAP purge* is being performed. *: Gasoline vapor from the fuel tank is being introduced into the intake system via the purge VSV. ·
When the engine is cold or immediately after the engine is started, EVAP (Purge) VSV is 0%. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Purge Cut VSV Duty | Purge VSV duty/
Min.: 0%, Max.: 399.9% |
- | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): 3.4% ·
Running without load (3000 rpm): 20.3% |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Evap Purge Flow | Purge flow/
Min.: 0%, Max.: 400% |
- | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): 0.0% ·
Running without load (3000 rpm): 5.4% |
|||
| Diagnostic Note:
This is the percentage of total engine airflow contributed by EVAP purge operation. (Evap Purge Flow = Purge flow / Engine airflow x 100 (%)) It is based on MAF and a stored value for airflow and controlled by adjusting the duty cycle for the purge VSV. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Purge Density Learn Value | Purge density learned value/
Min.: -200, Max.: 200 |
- | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): 0.000 |
|||
| Diagnostic Note:
Purge Density Learn Value is the proportion of the decrease in injection volume (based on the change in the air-fuel ratio feedback compensation value) related to a 1% purge flow rate. When Purge Density Learn Value is a large negative value, the purge effect is large. The purge density is determined from the change in the air-fuel ratio feedback compensation value when purge flow is introduced. Purge density learning is performed so that the feedback compensation value is 0 +/-2%.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| EVAP Purge VSV | VSV status for EVAP control/
ON or OFF |
- | Yes |
| Diagnostic Note:
This parameter displays ON when EVAP (Purge) VSV is 30% or more, and displays OFF when the VSV duty ratio is less than 30%. |
|||
Air Fuel Ratio Control 1 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Target Air-Fuel Ratio | Target air-fuel ratio/
Min.: 0, Max.: 2 |
0.8 to 1.2: Idling | Yes |
| Diagnostic Note:
This is the target air-fuel ratio used by the ECM. 1.0 is the stoichiometric air-fuel ratio. Values that are more than 1 indicate the system attempting to make the air-fuel ratio leaner. Values that are less than 1 indicate the system attempting to make the air-fuel ratio richer. |
|||
Air Fuel Ratio Control 2 (Ptrl AF O2 Sensor)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| AF Lambda B1S1 | Output air-fuel ratio associated with sensor 1/
Min.: 0, Max.: 2 |
·
Value less than 1 (0.000 to 0.999) = Rich ·
1 = Stoichiometric air fuel ratio ·
Value more than 1 (1.001 to 1.99) = Lean |
Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): 1.001 ·
Running without load (3000 rpm): 1.003 |
|||
| Diagnostic Note:
This is the actual air-fuel ratio calculated based on the air fuel ratio sensor output. Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check the voltage output of the sensor. Results of real-vehicle check when performing the Active Test: Injection Volume: +/-0% ·
AF Lambda B1S1: 0.999 ·
AFS Voltage B1S1: 3.317 V ·
AFS Current B1S1: 0.00 mA ·
O2S B1S2: 0.800 V Injection Volume: -12% ·
AF Lambda B1S1: 1.146 ·
AFS Voltage B1S1: 3.825 V ·
AFS Current B1S1: 0.32 mA ·
O2S B1S2: 0.015 V Injection Volume: +12% ·
AF Lambda B1S1: 0.928 ·
AFS Voltage B1S1: 2.849 V ·
AFS Current B1S1: -0.29 mA ·
O2S B1S2: 0.935 V |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage for sensor 1/
Min.: 0 V, Max.: 8 V |
2.8 to 3.8 V: Idling | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): 3.327 V ·
Running without load (3000 rpm): 3.317 V |
|||
| Diagnostic Note:
·
This is the voltage output of the air fuel ratio sensor (the voltage cannot be measured at the terminals of the sensor). This value is calculated by the ECM based on the current output of the air fuel ratio sensor (refer to AFS Current below for the actual sensor output). ·
Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check the voltage output of the sensor. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| AFS Current B1S1 | Air fuel ratio sensor output current for sensor 1/
Min.: -128 mA, Max.: 128 mA |
-0.5 to 0.5 mA: Idling | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): 0.00 mA ·
Running without load (3000 rpm): 0.01 mA |
|||
| Diagnostic Note:
·
With a stoichiometric air-fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor current output is approximately -0.5 to 0.5 mA. ·
When the value is outside the range of 0.7 to 2.2 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor or sensor circuit. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Heater Duty B1S1 | Air fuel ratio sensor heater duty ratio for sensor 1/
Min.: 0%, Max.: 399.9% |
0 to 100% | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): 21.8% |
|||
| Diagnostic Note:
When the value is any value except 0%, current is being supplied to the heater. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| O2S B1S2 | Heated oxygen sensor output voltage for sensor 2/
Min.: 0 V, Max.: 1 V |
0 to 1 V:
Driving at 70 km/h (43 mph) |
Yes |
·
Idling (warm up the engine): 0.720 V ·
Running without load (3000 rpm): 0.330 V |
|||
| Diagnostic Note:
This is the output voltage of the heated oxygen sensor. Values close to 0 V indicate an air-fuel ratio leaner than the stoichiometric ratio. Values close to 1 V indicate an air-fuel ratio richer than the stoichiometric ratio. During air-fuel ratio feedback control, the value moves back and forth in the range of 0 to 1 V. Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check voltage output of the sensor. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| O2S Impedance B1S2 | Heated oxygen sensor impedance for sensor 2/
Min.: 0 ohm, Max.: 21248 ohm |
5 to 15000 ohm | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): 236.35 ohm |
|||
| Diagnostic Note:
After driving approx. 10 min. in an urban area: 5 to 15000 ohm
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| O2 Heater B1S2 | Heated oxygen sensor heater for sensor 2/
Active or Not Act |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| O2 Heater Curr Val B1S2 | Heated oxygen sensor current for sensor 2/
Min.: 0 A, Max.: 4.999 A |
- | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): 0.976 A ·
Running without load (3000 rpm): 0.981 A |
|||
| Diagnostic Note:
When the value is any value except 0 A, current is being supplied to the heater. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Short FT #1 | Short-term fuel trim/
Min.: -100%, Max.: 99% |
-15 to 15% | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): -3.125% ·
Running without load (3000 rpm): 0.781% |
|||
| Diagnostic Note:
This item is the "short-term fuel injection volume compensation ratio" used to maintain the air-fuel ratio at the stoichiometric ratio using the heated oxygen sensor bank 1 sensor 1 for feedback. It is possible to check this value for each bank. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Long FT #1 | Long-term fuel trim/
Min.: -100%, Max.: 99% |
-15 to 15% | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): -3.907% ·
Running without load (3000 rpm): -5.469% |
|||
| Diagnostic Note:
The ECM will learn the Long FT values based on Short FT. The goal is to keep Short FT at 0% to keep the A/F mixture at the stoichiometric ratio. This value is used to determine whether the system related to air-fuel ratio control is malfunctioning. The condition of the system is determined based on the sum of Short FT and Long FT (excluding times when the system is in transition). ·
+15% or more: There may be a lean air-fuel ratio. ·
-15 to +15%: The air-fuel ratio can be determined to be normal. ·
-15% or less: There may be a rich air-fuel ratio. ·
The learned value is cleared when the battery cable is disconnected. ·
Air-fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range. "A/F Learn Value Idle #1", "A/F Learn Value Low #1", "A/F Learn Value Mid1 #1", "A/F Learn Value Mid2 #1" and "A/F Learn Value High #1" indicate the learned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Learn Value Idle #1 | Air-Fuel Learn Value of idle area/
Min.: -50%, Max.: 50% |
-15% to +15% | Yes |
| Diagnostic Note:
Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Learn Value Low #1 | Air-Fuel Learn Value of low load area/
Min.: -50%, Max.: 50% |
-15% to +15% | Yes |
| Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Learn Value Mid1 #1 | Air-Fuel Learn Value of middle 1 load area/
Min.: -50%, Max.: 50% |
-15% to +15% | Yes |
| Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Learn Value Mid2 #1 | Air-Fuel Learn Value of middle 2 load area/
Min.: -50%, Max.: 50% |
-15% to +15% | Yes |
| Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Learn Value High #1 | Air-Fuel Learn Value of high load area/
Min.: -50%, Max.: 50% |
-15% to +15% | Yes |
| Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Total FT #1 | Total fuel trim/
Min.: -1, Max.: 0 |
-0.2 to 0.2: Idling | Yes |
| Diagnostic Note:
Total FT #1 = Short FT #1 + Long FT #1 |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel System Status #1 | Fuel system status/
Unused, OL, CL, OLDrive, OLFault or CLFault |
CL: Idling after warming up | Yes |
| Diagnostic Note:
·
OL (Open Loop): Has not yet satisfied conditions to go to closed loop. ·
CL (Closed Loop): Feedback for fuel control. ·
OL Drive: Open loop due to driving conditions (fuel enrichment). ·
OL Fault: Open loop due to a detected system fault. ·
CL Fault: Closed loop but the heated oxygen sensor bank1 sensor1, which is used for fuel control, is malfunctioning. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel System Status #2 | Fuel system status for bank 2/
Unused, OL, CL, OLDrive, OLFault or CLFault |
Unused | Yes |
Ignition System (Ignition)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| IGN Advance | Ignition timing advance for No. 1 cylinder/
Min.: -64 deg., Max.: 64 deg. |
BTDC 0 to 14 deg.: Idling | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): 7.5 deg ·
Running without load (3000 rpm): 33.0 deg |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Knock Feedback Value | Knocking feedback value/
Min.: -1024 deg(CA), Max.: 1024 deg(CA) |
- | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): -1.5 deg(CA) ·
Running without load (3000 rpm): -1.5 deg(CA) |
|||
| Diagnostic Note:
This is the ignition timing retard compensation amount determined by the presence or absence of knocking. Ignition timing = Most retarded timing value*1 + Knock Correct Learn Value*2 + Knock Feedback Value*3 + each compensation amount Example: 21 deg(CA) = 10° + 14° - 3° *1: The most retarded timing value is a constant determined by the engine speed and engine load. *2: The knock correction learned value is calculated as shown below in order to keep Knock Feedback Value as close to -3 deg(CA) as possible. When Knock Feedback Value is less than -4 deg(CA), Knock Correct Learn Value is slowly decreased. When Knock Feedback Value is more than -2 deg(CA), Knock Correct Learn Value is slowly increased. *3: The base value is -3 deg(CA) and is adjusted based on the presence or absence of knocking. When there is no knocking, the value is increased, and when knocking is present, the value is decreased. -1 deg(CA): There is no knocking and ignition timing is advanced. -6 deg(CA): Knocking is present and the ignition timing is being retarded.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Knock Correct Learn Value | Knocking correction learned value/
Min.: -1024 deg(CA), Max.: 1024 deg(CA) |
- | Yes |
| Results of real-vehicle check:
·
Idling (warm up the engine): 10.2 deg(CA) ·
Running without load (3000 rpm): 9.0 deg(CA) |
|||
| Diagnostic Note:
Refer to "Knock Feedback Value". When there is knocking or a lack of power, compare the following values to another vehicle of the same model. ·
Engine speed ·
Calculate Load ·
IGN Advance ·
Knock Feedback Value ·
Knock Correct Learn Value Knock Correct Learn Value is large: There is no knocking and the ignition timing is advanced. Knock Correct Learn Value is small: Knocking is present and the ignition timing is being retarded.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Idle Spark Advn Ctrl #1
Idle Spark Advn Ctrl #2 Idle Spark Advn Ctrl #3 Idle Spark Advn Ctrl #4 |
Individual cylinder timing advance compensation amount (No. 1 to No.4)/
Min.: 0 deg(CA), Max.: 16 deg(CA) |
- | Yes |
| Diagnostic Note:
·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling. ·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
|||
VVT Control 1 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Actual VVT Angle #1 | Actual VVT Angle #1/
Min.: 0 DegFR, Max.: 639.99 DegFR |
- | Yes |
| Diagnostic Note:
This item is displayed only for freeze frame data. |
|||
VVT Control 2 (Ptrl Valve Control)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VVT Control Status #1 | Variable valve Timing (VVT) control status/
ON or OFF |
- | Yes |
| Diagnostic Note:
ON: The ECM is sending commands to change the timing (even when the timing is advanced, when the timing is being maintained and not being retarded or advanced any further, the value changes to OFF). OFF: The system is commanding the timing to change to the most retarded timing. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VVT Advance Fail | VVT control failure status/
ON or OFF |
ON: When VVT advance fails | Yes |
| Diagnostic Note:
ON: There is an intake VVT timing advance malfunction. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VVT Aim Angle #1 | VVT hold duty learned value/
Min.: 0%, Max.: 399.9% |
- | Yes |
| Diagnostic Note:
This value represents the duty ratio necessary to operate the camshaft timing oil control valve in order to block the camshaft timing oil control valve path and maintain the advanced state of the VVT controller. Refer to "VVT OCV Duty #1". |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VVT Change Angle #1 | VVT displacement angle/
Min.: 0 DegFR, Max.: 639.9 DegFR |
- | Yes |
| Diagnostic Note:
This is the VVT displacement angle during forced operation. By checking VVT Change Angle during the Active Test, it is also possible to determine whether or not the camshaft position sensor signal is being output. Refer to "VVT OCV Duty #1". |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VVT OCV Duty #1 | VVT camshaft timing oil control valve operation duty/
Min.: 0%, Max.: 399.9% |
- | Yes |
| Diagnostic Note:
This is the requested duty value for forced operation. Results of the real-vehicle check when performing the Control the VVT Linear (Bank 1) Active Test: VVT OCV Duty #1 = 0%, VVT Change Angle #1 = 0 DegFR ↓ VVT OCV Duty #1 = 38%, VVT Change Angle #1 = 0 DegFR ↓ VVT OCV Duty #1 = 46%, VVT Change Angle #1 = 0 DegFR ↓ VVT OCV Duty #1 = 54%, VVT Change Angle #1 = 0 DegFR ↓ VVT OCV Duty #1 = 57%, VVT Change Angle #1 = 0.3 DegFR ↓ VVT OCV Duty #1 = 58%, VVT Change Angle #1 = 13.0 DegFR ↓ VVT OCV Duty #1 = 59%, VVT Change Angle #1 = 35.2 DegFR After the above test, VVT Aim Angle #1 = 37.0%. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VVT Target Angle #1 | VVT target angle for bank 1/
Min.: 0 DegFR, Max.: 639.9 DegFR |
- | Yes |
Various Vehicle Conditions 2 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VN Turbo Type | VN turbo type/
Not Avl, Commo, Vacuum, CAN Com or DC |
Not Avl | No |
Catalyst (Ptrl CAT Converter)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Catalyst Temp B1S1 | Catalyst temperature for sensor 1/
Min.: -40°C, Max.: 6514°C |
- | Yes |
| Diagnostic Note:
This is the temperature of the front catalyst estimated by the ECM. This value is included in the conditions used to detect catalyst deterioration (DTC P0420), etc., and should therefore be used as a reference when recreating malfunction conditions. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Catalyst Temp B1S2 | Catalyst temperature for sensor 2/
Min.: -40°C, Max.: 6514°C |
- | Yes |
| Diagnostic Note:
This is the temperature of the rear catalyst estimated by the ECM. |
|||
Various Vehicle Conditions 3 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Starter Signal | Starter signal/
ON or OFF |
ON: Starter operating
OFF: Starter not operating |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Power Steering Signal | Power steering switch signal/
ON or OFF |
ON: Power steering operation | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Neutral Position SW Signal | PNP switch status/
ON or OFF |
ON: Shift lever in P or N | Yes |
| Diagnostic Note:
This item is displayed only for Automatic Transaxle. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Clutch Switch | Clutch switch status/
ON or OFF |
ON: Clutch pedal depressed | Yes |
| Diagnostic Note:
This item is displayed only for vehicle with Manual Transaxle. Clutch switch (upper) signal status for cruise control system |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Clutch Start SW | Clutch start switch status/
ON or OFF |
ON: Clutch pedal depressed
OFF: Clutch start switch released |
Yes |
| Diagnostic Note:
This item is displayed only for Manual Transaxle. Clutch start switch (lower) signal status for engine cranking |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Stop Light Switch | Stop light switch/
ON or OFF |
ON: Brake pedal depressed
OFF: Brake pedal released |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/C Signal | A/C switch status/
ON or OFF |
ON: A/C on | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Closed Throttle Position SW | Closed throttle position switch/
ON or OFF |
·
ON: Throttle fully closed ·
OFF: Throttle open |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel Cut Condition | Fuel cut condition/
ON or OFF |
ON: Fuel cut operating | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Immobiliser Communication | Immobiliser communication/
ON or OFF |
ON: Normal | Yes |
Check Mode (Check Mode)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Test Results #1 | Check mode result for air fuel ratio sensor (Bank 1)/ Compl or Incmpl | - | No |
Test Result (Monitor Status)
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note | Stored as Freeze Frame Data |
|---|---|---|---|---|
| Complete Parts Monitor | Comprehensive component monitor/
Not Avl or Avail |
- | * | No |
| Fuel System Monitor | Fuel system monitor/
Not Avl or Avail |
- | * | No |
| Misfire Monitor | Misfire monitor/
Not Avl or Avail |
- | * | No |
| EGR/VVT Monitor | EGR/VVT monitor/
Not Avl or Avail |
- | * | No |
| EGR/VVT Monitor | EGR/VVT monitor/
Compl or Incmpl |
- | * | No |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/
Not Avl or Avail |
- | * | No |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/
Compl or Incmpl |
- | * | No |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/
Not Avl or Avail |
- | * | No |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/
Compl or Incmpl |
- | * | No |
| A/C Monitor | A/C monitor/
Not Avl or Avail |
- | * | No |
| A/C Monitor | A/C monitor/
Compl or Incmpl |
- | * | No |
| 2nd Air Monitor | 2nd air monitor/
Not Avl or Avail |
- | * | No |
| 2nd Air Monitor | 2nd air monitor/
Compl or Incmpl |
- | * | No |
| EVAP Monitor | EVAP monitor/
Not Avl or Avail |
- | * | No |
| EVAP Monitor | EVAP monitor/
Compl or Incmpl |
- | * | No |
| Heated Catalyst Monitor | Heated catalyst monitor/
Not Avl or Avail |
- | * | No |
| Heated Catalyst Monitor | Heated catalyst monitor/
Compl or Incmpl |
- | * | No |
| Catalyst Monitor | Catalyst monitor/
Not Avl or Avail |
- | * | No |
| Catalyst Monitor | Catalyst monitor/
Compl or Incmpl |
- | * | No |
| *:
Avail: The monitor is available on the vehicle. Not Avl: The monitor is not available on the vehicle. Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected. |
||||
Various Vehicle Conditions 4 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| TC Terminal | TC terminal status/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| # Codes (Include History) | Number of codes/
Min.: 0, Max.: 255 |
0 | Yes |
| Diagnostic Note:
This is the number of DTCs stored. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| MIL | MIL status/
ON or OFF |
OFF | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| MIL ON Run Distance | Distance driven with MIL ON/
Min.: 0 km, Max.: 65535 km |
- | No |
| Diagnostic Note:
This is the distance driven after a DTC is stored (MIL turns on). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Running Time from MIL ON | Running time from MIL ON/
Min.: 0 min, Max.: 65535 min |
Running time after MIL turned on | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Time after DTC Cleared | Time after DTCs cleared/
Min.: 0 min, Max.: 65535 min |
Time after DTCs cleared | Yes |
| Diagnostic Note:
This is the time elapsed after DTCs were cleared (or after the vehicle left the factory). Time elapsed after the ignition switch is turned off is not counted. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Distance from DTC Cleared | Distance driven after DTCs cleared/
Min.: 0 km, Max.: 65535 km |
Distance driven after DTCs cleared | Yes |
| Diagnostic Note:
This is the distance driven after DTCs were cleared (or after the vehicle left the factory). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared/
Min.: 0, Max.: 255 |
- | Yes |
| Diagnostic Note:
This is the number of warmup cycles after the DTCs were cleared. This is the number of times the engine was warmed up* after DTCs were cleared (or after the vehicle left the factory). *: An engine warmup is defined as the engine coolant temperature rising 20°C (36°F) or more and reaching a temperature of 70°C (158°F) or higher after the engine is started. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Dist Batt Cable Disconnect | Distance driven after battery cable disconnected/
Min.: 0 km, Max.: 65535 km |
Total distance vehicle driven after battery cable disconnected | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| IG OFF Elapsed Time | Time after ignition switch off/
Min.: 0 min, Max.: 655350 min |
Cumulative time after ignition switch off | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| OBD Requirements | OBD requirement | EOBD (Euro OBD) | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Number of Emission DTC | Emissions-related DTCs | - | No |
| Diagnostic Note:
This is the number of emissions-related DTCs. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| TC and TE1 | TC and CG (TE1) terminals of DLC3/
ON or OFF |
- | Yes |
Various Vehicle Conditions 5 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Speed (Starter Off) | Engine speed when starter off/
Min.: 0 rpm, Max.: 51199 rpm |
- | Yes |
| Results of real-vehicle check:
Idling (warm up the engine): 1630 rpm |
|||
| Diagnostic Note:
This is the engine speed immediately after starting the engine. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Starter Count | Number of times starter turned on after ignition switch turned to ON/
Min.: 0, Max.: 255 |
- | Yes |
| Diagnostic Note:
·
Indicates the number of times starter turned ON in the current driving cycle. ·
Number of times starter turned ON before engine started displayed in the 1 position. ·
Number of times starter turned ON after engine started displayed in the 10 position. Example: If "21" is displayed on the GTS, the starter was turned ON 1 time before engine start and turned ON 2 times after engine start. (The maximum value for each counter is 9 times before engine start and 11 times after engine start) |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Run Dist of Previous Trip | Distance driven during previous trip/
Min.: 0 km, Max.: 655.35 km |
- | Yes |
| Diagnostic Note:
Before 5 seconds elapse after starting the engine, which is DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
|
|||
Rough Idle (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Compression Leakage Count | Compression leakage count/
Min.: 0, Max.: 255 |
0 | Yes |
| Diagnostic Note:
·
When the counter displays 5 or higher during an engine stall, startability malfunction or rough idle, it may be the result of pressure loss caused by deposits jamming the valve, etc. ·
This item is displayed only for Automatic Transaxle. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Rough Idle Status | Status of the rough idle status/
Normal, Misfire, Continuous poor combustion, Intermittent poor combustion, Low frequency poor combustion |
Normal | Yes |
| Diagnostic Note:
·
The following list of statuses indicates the degree and frequency of rough idling from highest to lowest. Use this as a reference when trying to reproduce the rough idling. 1.
Misfire 2.
Continuous poor combustion 3.
Intermittent poor combustion 4.
Low frequency poor combustion ·
This item is displayed only for Automatic Transaxle. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Plural Cylinders Rough Idle | Status of the plural cylinders rough idle/
ON or OFF |
OFF | Yes |
| Diagnostic Note:
·
Indicates multiple cylinders are the cause of rough idling when ON. ·
This item is displayed only for Automatic Transaxle. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Rough Idle #1
Rough Idle #2 Rough Idle #3 Rough Idle #4 |
Status of the rough idle #1 to #4/
ON or OFF |
OFF | Yes |
| Diagnostic Note:
·
Indicates speed has dropped compared to other cylinders and idling is rough for the indicated cylinder when ON. ·
This item indicates cylinders which are likely to be the cause of rough idle. ·
This item is displayed only for Automatic Transaxle. |
|||
Various Vehicle Conditions 6 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Starting Time | Time elapsed before engine starts (after starter turns on until engine speed reaches 400 rpm)/
Min.: 0 ms, Max.: 655350 ms |
- | Yes |
| Diagnostic Note:
This is the time elapsed after the starter turns on until the engine speed reaches 400 rpm. This value is cleared 5 seconds after the engine is started and the value is displayed as 0 ms. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Previous Trip Coolant Temp | Engine coolant temperature during previous trip/
Min.: -40°C, Max.: 215°C |
- | Yes |
| Diagnostic Note:
Before 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature at the end of the previous trip. After 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature during the current trip. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Previous Trip Intake Temp | Intake air temperature during previous trip/
Min.: -40°C, Max.: 215°C |
- | Yes |
| Diagnostic Note:
Before 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature at the end of the previous trip. After 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature during the current trip. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Oil Temperature | Engine oil temperature (estimated temperature)/
Min.: -40°C, Max.: 215°C |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Previous Trip Eng Oil Temp | Engine oil temperature during previous trip/
Min.: -40°C, Max.: 215°C |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Ambient Temp for A/C | Ambient temperature for A/C/
Min.: -40°C, Max.: 215°C |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Previous Trip Ambient Temp | Ambient temperature during previous trip/
Min.: -40°C, Max.: 215°C |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Start Hesitation | History of hesitation during engine start/
ON or OFF |
- | Yes |
| Diagnostic Note:
This value changes to ON when the engine speed does not reach 500 rpm during cranking. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Low Rev for Eng Start | History of low engine speed after engine start/
ON or OFF |
- | Yes |
| Diagnostic Note:
This flag changes to ON when the engine speed drops to 200 rpm or less within approximately 2 seconds of starting the engine. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel Cut Elps Time | Elapsed time since fuel cut due to high engine speed
Min.: 0 sec Max.: 68746 sec |
- | Yes |
| Diagnostic Note:
The time elapsed after a fuel cut after high engine speed has occurred (More than the rpm at which fuel cut occurs + 500 rpm). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Electric Fan Motor | Electric fan motors operation status/
ON or OFF |
ON: Electric fan motor operating | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Brake Override System | Brake override system status/
ON or OFF |
ON: Brake override system operating | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Electric Cooling Fan High | Electric fan motor operation status/
ON or OFF |
ON: Cooling fan operated at high speed | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Electric Cooling Fan Low | Electric fan motor operation status/
ON or OFF |
ON: Cooling fan operated at low speed | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Idle Fuel Cut | Fuel cut at idle/
ON or OFF |
ON: Fuel cut operating | Yes |
| Diagnostic Note:
Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is high. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| FC TAU | Fuel cut TAU (fuel cut during very light load)/
ON or OFF |
ON: Fuel cut operating | Yes |
| Diagnostic Note:
This is the fuel cut performed under a very light load to prevent the engine combustion from becoming incomplete. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Immobiliser Fuel Cut | Status of immobiliser fuel cut/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Immobiliser Fuel Cut History | Status of the immobiliser fuel cut history/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Electrical Load Signal 1 | Electrical load signal/
ON or OFF |
ON: Tail switch ON | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Electrical Load Signal 2 | Electrical load signal/
ON or OFF |
ON: Rear defogger switch ON | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Cruise Main SW | Cruise control main switch operation status/
ON or OFF |
ON: Cruise control main switch (ON-OFF button) pushed
OFF: Cruise control main switch (ON-OFF button) not pushed |
Yes |
Various Vehicle Conditions 7 (Vehicle Information)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Model Code | Model code | - | No |
| Diagnostic Note:
Used for identifying the model code: NCP13# |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Type | Engine type | - | No |
| Diagnostic Note:
Used for identifying the engine type: 2NZ-FE |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Cylinder Number | Number of cylinders/
Min.: 0 Max.: 255 |
- | No |
| Diagnostic Note:
Used for identifying the number of cylinders: 4 |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Destination | Destination | - | No |
| Diagnostic Note:
Used for identifying the destination: W |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Model Year | Model year/
Min.: 1900 Max.: 2155 |
- | No |
| Diagnostic Note:
Used for identifying the model year: 20## |
|||
Compression (Compression)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Speed of Cyl #1
Engine Speed of Cyl #2 Engine Speed of Cyl #3 Engine Speed of Cyl #4 |
Engine speed for cylinder No. 1 to No. 4/
Min.: 0 rpm, Max.: 51199 rpm |
- | Yes |
| Diagnostic Note:
This is output only when Check the Cylinder Compression is performed using the Active Test. This is the engine speed for each cylinder measured during the fuel-cut with the engine cranking. When there is compression loss, the engine speed for that cylinder increases.
Results of real-vehicle check when performing the Active Test with a normal vehicle: ·
Engine Speed of Cyl #1: 260 rpm ·
Engine Speed of Cyl #2: 259 rpm ·
Engine Speed of Cyl #3: 258 rpm ·
Engine Speed of Cyl #4: 257 rpm |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Av Engine Speed of All Cyl | Average engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm |
- | Yes |
| Diagnostic Note:
This is output only when Check the Cylinder Compression is performed using the Active Test. |
|||
Automatic Transaxle System 1 (All Data)
Refer to Automatic Transaxle System (See page Drivetrain>U441E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| SPD (NT) | Input shaft speed/
Min.: 0 rpm Max.: 12750 rpm |
·
Lock-up on (after warming up engine): Input turbine speed (NT) equal to engine speed ·
Lock-up off (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed |
Yes |
| Diagnostic Note:
Data is displayed in increments of 50 rpm. This item is displayed only for Automatic Transaxle. |
|||
Automatic Transaxle System 2 (AT)
Refer to Automatic Transaxle System (See page Drivetrain>U441E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/T Oil Temperature 1 | ATF temperature sensor value/
Min.: -40°C, Max.: 215°C |
·
After stall test: Approximately 80°C (176°F) ·
Equal to ambient temperature when engine cold |
Yes |
| Diagnostic Note:
If the value is -40°C (-40°F) or 150°C (302°F), the ATF temperature sensor circuit is open or shorted. This item is displayed only for Automatic Transaxle. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Lock Up | Lock up status/
ON or OFF |
·
Lock-up operating: ON ·
Lock-up not operating: OFF |
Yes |
| Diagnostic Note:
This item is displayed only for Automatic Transaxle. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Shift Status | ECM gearshift command/
1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th |
Shift lever in D: 1st, 2nd, 3rd or 4th | Yes |
| Diagnostic Note:
This item is displayed only for Automatic Transaxle. |
|||
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
As DTCs may be stored when an Active Test or learning is performed, make sure to clear the DTCs before returning the vehicle to the customer.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Injection Volume | Change injection volume | Between -12.5% and 24.8% | ·
All injectors are tested at the same time. ·
Perform the test at or below 3000 rpm. ·
Injection volume can be changed in fine gradations within control range. ·
Control the Injection Volume enables the checking and graphing of the heated oxygen sensor voltage outputs. ·
To conduct the test, enter the following menus: Active Test / Control the Injection Volume / AFS Voltage B1S1 and O2S B1S2. ·
During the Active Test, air-fuel ratio feedback control and feedback learning are stopped. |
| Control the Injection Volume for A/F Sensor | Change injection volume | -12.5%/0%/12.5% | ·
All injectors are tested at the same time. ·
Perform the test at or below 3000 rpm. ·
Control the Injection Volume for A/F Sensor enables the checking and graphing of the heated oxygen sensor voltage outputs. ·
To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2. ·
During the Active Test, air-fuel ratio feedback control and feedback learning are stopped. ·
See waveform *2 |
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF | ·
The valve is opened with a 30% duty ratio. ·
See waveform *4 |
| Control the Fuel Pump/Speed | Activate fuel pump | ON/OFF | Perform this test with the engine stopped. |
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF | ·
ON: TC and TE1 are connected. ·
OFF: TC and TE1 are disconnected. |
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | - |
| Control the Electric Cooling Fan | Control electric cooling fan motor | ON/OFF | - |
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Close/Open
Open: Throttle valve opens slowly |
This test is possible when the following conditions are met:
·
Ignition switch is ON. ·
Engine is stopped. ·
Accelerator pedal is fully depressed (APP: 58 degrees or more). ·
Shift lever is in P (neutral). |
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Close/Open
Open: Throttle valve opens quickly |
·
Same as above. ·
See waveform *3 |
| Control the VVT Linear (Bank 1) | Control VVT | -128 to 127% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum advance -100%: Maximum retard |
·
Engine stalls or idles roughly when the VVT actuator is operated by 100%. ·
Test is possible during idle. ·
See waveform *5 ·
DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction. |
| Control the VVT System (Bank 1) | Turn camshaft timing oil control valve on and off | ON/OFF
ON: VVT OCV Duty #1 100% |
·
Engine stalls or idles roughly when the camshaft timing oil control valve is turned on. ·
Engine runs and idles normally when the camshaft timing oil control valve is off. ·
DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction. |
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #4) injector fuel cut | #1/#2/#3/#4
OFF/ON |
This test is possible when the following conditions are met:
·
Vehicle is stopped. ·
Engine is idling. ·
Shift lever is in P (neutral). |
| Control the All Cylinders Fuel Cut | All cylinder fuel cut | ON/OFF | Test is possible while the vehicle is stopped and the engine is idling. |
| Check the Cylinder Compression*1 | Check the cylinder compression pressure | ON/OFF | Fuel injection and ignition stop in all cylinders. |
*1: When cranking the engine, each cylinder measures the engine speed.
In this Active Test, the fuel and ignition of all cylinders is cut and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.
To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.
Push the snapshot button to turn the snapshot function on.
Using the snapshot function, data can be recorded during the Active Test.
While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.
After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.
Crank the engine for about 10 seconds.
Continue to crank the engine until the values change from the default value (51199 rpm).
Monitor the engine speed (Engine Speed of Cyl #1 to #4) displayed on the GTS.
At first, the GTS displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.
Do not crank the engine continuously for 20 seconds or more.
If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.
Use a fully-charged battery.
Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.
If the Active Test is changed to OFF while the engine is being cranked, the engine will start.
Push the snapshot button to turn the snapshot function off.
Select "Stored Data" on the GTS screen, select the recorded data and display the data as a graph.
If the data is not displayed as a graph, the change of the values cannot be observed.
Check the change in engine speed values.
As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.
*2: Control the Injection Volume for A/F Sensor (Idling after warming up)
During the Active Test, air-fuel ratio feedback control and feedback learning are stopped.
| GTS Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Control the Injection Volume for A/F Sensor | - | ▲A | ▲B |
| Active Test operation | -12.5% | 12.5% | |
| AFS Voltage B1S1 | 3.803 V | 2.796 V | |
| O2S B1S2 | 0.015 V | 0.935 V | |
Usually, the value of AFS Voltage B1S1 drops below 3.1 V when the control value for Control the Injection Volume for A/F Sensor is changed to 12.5%.
Usually, the value of AFS Voltage B1S1 changes to 3.4 V or higher when the control value for Control the Injection Volume for A/F Sensor is changed to -12.5%.
Usually, the value of O2S B1S2 changes to 0.55 V or higher when the control value for Control the Injection Volume for A/F Sensor is changed to 12.5%.
Usually, the value of O2S B1S2 drops below 0.4 V when the control value for Control the Injection Volume for A/F Sensor is changed to -12.5%.
*3: Control the ETCS Open/Close Fast Speed [Active Test for electrical throttle control system] (Ignition switch ON)
Usually, Throttle Position Command (Target Value) and Throttle Position No. 1 (Actual Value) are almost the same.
If any DTCs related to the ETCS are stored, this Active Test does not function.
| GTS Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Control the ETCS Open/Close Fast Speed | - | ▲A | ▲B |
| Active Test operation | Open | Close | |
| Throttle Position Command | 2.597 V | 0.800 V | |
| Throttle Position No. 1 | 2.597 V | 0.800 V | |
| Throttle Motor Duty (Open) | 18% | 0% | |
| Throttle Motor Duty (Close) | 0% | 17% | |
*4: Activate the VSV for Evap Control (Idling after warming up)
Even when the Active Test is turned on (the purge VSV is opened 30%), air-fuel ratio feedback continues and control is performed so that the air-fuel ratio is the stoichiometric ratio. Therefore, by observing the change in "Short FT", it is possible to determine whether the purge VSV is actually open as well as the concentration of HC in the purge gas.
| GTS Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Activate the VSV for Evap Control | - | ▲A | ▲B |
| Active Test operation | ON | OFF | |
| EVAP (Purge) VSV | 29.8% | 0.0% | |
| Injection (Port) | 2603 μs | 2631 μs | |
| AFS Voltage B1S1 | 3.221 V | 3.311 V | |
The graphs and values above are for reference only because the feedback volume varies depending on the HC density of the purge air (HC volume absorbed by the canister).
*5: Control the VVT Linear (Bank 1)
| GTS Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Control the VVT Linear (Bank 1) | - | ▲A | ▲B |
| Active Test operation* | +25% | -25% | |
| VVT Change Angle #1 | 41.2 DegFR | 0.0 DegFR | |
| VVT OCV Duty #1 | 59.5 % | 11.5 % | |
| VVT Aim Angle #1 | 35.5 % | 35.5 % | |
*: Change the control value for Control the VVT Linear to +25% or -25% in increments of 5%.
The Control the VVT Linear Active Test considers the value of VVT Aim Angle to be 0 and raises or lowers the duty ratio with respect to VVT Aim Angle.
The sum of the control value for the Control the VVT Linear Active Test and the value of VVT Aim Angle is approximately equal to the value of VVT OCV Duty.
When the control value for the Control the VVT Linear Active Test is changed a few times, there should not be a large discrepancy between VVT OCV Duty when the system starts advancing or retarding the timing and the rate of change of VVT Change Angle.