Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The wheel speed sensors monitor the wheel rotation speed and send signals to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter. Check all the components possibly related to speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



A079413E63
0.292,1.177 1.031,1.885 0.74,0.708 10 false from Speed Sensor 1.573,0.99 2.375,1.323 0.802,0.333 10 false Skid Control ECU 2.719,0.469 3.302,0.667 0.583,0.198 10 false 4-Pulse 4.656,0.469 5.24,0.667 0.583,0.198 10 false 4-Pulse 3.396,1.833 4.646,2.208 1.25,0.375 10 false Combination Meter Assembly 5.781,1.198 6.167,1.396 0.385,0.198 10 false ECM

DTC No. DTC Detection Condition Trouble Area
P0500 While vehicle is being driven, no vehicle speed sensor signal is sent to the ECM.
(1 trip detection logic: automatic transaxle)
(2 trip detection logic: manual transaxle)
·

Open or short in speed signal circuit

·

Combination meter assembly

·

Skid control ECU

·

ECM



MONITOR DESCRIPTION

Automatic Transaxle Models

The ECM assumes that the vehicle is being driven when the indicated engine speed is more than 2000 rpm and 30 seconds have elapsed since the Park/Neutral Position (PNP) switch was turned off (typical example value). If there is no speed signal from the combination meter, despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.


Manual Transaxle Models

The ECM assumes that the vehicle is being driven when fuel cut with the accelerator pedal released continues for 5 seconds or more. If there is no speed signal from the combination meter, despite this condition being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.


MONITOR STRATEGY

Required Sensors/Components (Main) Vehicle speed sensor, Combination meter and Skid control ECU
Required Sensors/Components (Related) Park/neutral position switch, Engine coolant temperature sensor, Throttle body with motor assembly and Mass air flow meter
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

A/T:
Ignition Switch ON
Time after ignition switch OFF to ON 3 seconds or more
Battery voltage 11 V or higher
Starter OFF
Time after PNP switch turned off 30 seconds

M/T:
Time after ignition switch turned from OFF to ON 3 seconds or more
Ignition switch ON
Starter OFF
Fuel-cut ON

TYPICAL MALFUNCTION THRESHOLDS

Vehicle speed sensor signal No pulse input

CONFIRMATION DRIVING PATTERN

A240416E04
0.661,0.879 1.859,1.104 1.198,0.225 10 24 km/h (14 mph) 1.421,2.049 1.820,2.219 0.399,0.170 10 Idling 0.596,2.399 1.772,2.583 1.177,0.184 10 Ignition Switch ON 2.387,2.273 2.620,2.443 0.232,0.169 10 [A] 4.706,0.473 4.911,0.642 0.205,0.170 10 [B] 6.249,3.287 6.447,3.484 0.198,0.198 10 [D] 6.062,1.12 6.260,1.317 0.198,0.198 10 [C] 4.012,3.052 5.817,3.197 1.805,0.145 10 Total of 30 seconds or more 4.32,3.453 5.511,3.599 1.191,0.145 10 5 seconds or more 6.084,2.945 5.902,3.529 5.902,3.529 5.533,3.529 false

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Drive the vehicle at 24 km/h (14 mph) or more for a total of 30 seconds or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

9.

Stop the vehicle.

10.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0500.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A254089E05
0.198,1.823 1.677,2.031 1.479,0.208 10 false from Skid Control ECU 2.135,1.615 2.25,1.781 0.115,0.167 10 false 5 2.104,1.813 2.354,1.99 0.25,0.177 10 false F1 2.396,1.698 2.583,1.885 0.188,0.188 10 false SI 3.594,1.677 3.823,1.865 0.229,0.188 10 false +S 2.188,2.656 4.083,2.917 1.896,0.26 10 false Combination Meter Assembly 3.948,1.813 4.229,2.073 0.281,0.26 10 false F1 3.979,1.625 4.146,1.792 0.167,0.167 10 false 6 4.865,1.813 5.24,2 0.375,0.188 10 false A83 4.927,1.635 5.208,1.854 0.281,0.219 10 false 44 5.229,1.698 5.625,1.885 0.396,0.188 10 false SPD 5.844,1.406 6.083,1.604 0.24,0.198 10 false 5 V 5.708,2.615 6.135,2.802 0.427,0.188 10 false ECM 5.188,2.979 6.188,3.177 1,0.198 10 false to Other ECUs

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.


e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

Result
Result Proceed to
Values displayed on GTS and speedometer display not equal A
Values displayed on GTS and speedometer display equal B



A

2.CHECK COMBINATION METER SYSTEM

B

2.CHECK COMBINATION METER SYSTEM
a.

Check the circuits that send vehicle speed signals to this system in the meter system (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



NEXT

3.CHECK WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CHECK WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).


d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

HINT:

If no DTCs (no pending DTCs) are output to the GTS, the repair has been successfully completed.




NEXT

END