Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) › 2016.09–2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248285 CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) U

NETWORKING  CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).





JUNCTION CONNECTOR


a.

NO. 1 JUNCTION CONNECTOR

U158584C02
1.385,1.302 1.073,1.052 true 1.479,1.292 1.146,0.875 true 1.396,1.5 1.083,1.74 true 1.49,1.5 1.156,1.917 true 5.813,1.333 6.063,1.281 true 5.813,1.49 6.063,1.521 true 5.531,1.292 5.875,0.688 true 5.521,1.5 5.865,2.104 true 1.646,0.344 1.917,0.51 0.271,0.167 10 false A61 0.5,0.958 1.052,1.146 0.552,0.188 10 false CANH*b 0.51,1.646 1.031,1.833 0.521,0.188 10 false CANL*b 0.594,0.75 1.146,0.938 0.552,0.188 10 false CANH*a 0.594,1.854 1.125,2.042 0.531,0.188 10 false CANL*a 5.188,0.354 5.458,0.521 0.271,0.167 10 false F82 6.115,1.177 6.99,1.365 0.875,0.188 10 false CANH*c 6.115,1.448 6.99,1.635 0.875,0.188 10 false CANL*c 5.938,0.552 6.75,0.74 0.813,0.188 10 false CANH*d 5.906,2.094 6.844,2.26 0.938,0.167 10 false CANL*d
*a to ECM *b to Skid Control ECU (Brake Actuator Assembly)
*c to Main Body ECU (Multiplex Network Body ECU) *d to No. 2 Junction Connector


Terminal No. (Symbol) Wiring Color Connect to
A61-9 (CANH) L ECM
A61-20 (CANL) W
A61-10 (CANH) G Skid Control ECU (Brake Actuator Assembly)
A61-21 (CANL) W
F82-1 (CANH) R Main Body ECU (Multiplex Network Body ECU)
F82-12 (CANL) W
F82-4 (CANH) SB No. 2 Junction Connector
F82-15 (CANL) W


b.

NO. 2 JUNCTION CONNECTOR

U158588C02
4.042,1.302 4.438,1.271 true 3.052,1.302 2.688,1.292 true 3.177,1.281 2.75,1.052 true 3.542,1.281 3.188,0.406 true 4.031,1.49 4.427,1.521 true 3.073,1.469 2.688,1.51 true 3.177,1.458 2.74,1.771 true 3.563,1.479 3.177,2.417 true 3.76,1.281 4.24,0.76 true 3.781,1.49 4.24,2.021 true 3.344,1.292 2.875,0.813 true 3.354,1.458 2.885,2.01 true 3.448,1.292 3.021,0.604 true 3.458,1.458 3.063,2.188 true 3.646,1.49 4.073,2.365 true 3.646,1.292 4.208,0.365 true 3.438,0.365 3.708,0.531 0.271,0.167 10 false F83 4.479,1.188 5.354,1.375 0.875,0.188 10 false CANH*a 4.469,1.458 5.344,1.646 0.875,0.188 10 false CANL*a 2.135,1.198 2.688,1.385 0.552,0.188 10 false CANH*h 2.125,1.448 2.646,1.635 0.521,0.188 10 false CANL*h 2.198,0.938 2.75,1.125 0.552,0.188 10 false CANH*f 2.198,1.698 2.719,1.885 0.521,0.188 10 false CANL*f 2.656,0.26 3.208,0.448 0.552,0.188 10 false CANH*c 2.667,2.385 3.198,2.573 0.531,0.188 10 false CANL*c 4.281,0.656 5.094,0.844 0.813,0.188 10 false CANH*b 2.344,0.698 3.156,0.885 0.813,0.188 10 false CANH*e 4.292,1.958 5.229,2.125 0.938,0.167 10 false CANL*b 2.365,1.927 3.302,2.094 0.938,0.167 10 false CANL*e 2.479,0.479 3.292,0.667 0.813,0.188 10 false CANH*d 2.5,2.146 3.438,2.313 0.938,0.167 10 false CANL*d 4.115,2.302 4.635,2.49 0.521,0.188 10 false CANL*g 4.24,0.26 4.927,0.448 0.688,0.188 10 false CANH*g
*a to Steering Angle Sensor (Spiral Cable Sub-assembly) *b to Airbag Sensor Assembly
*c to Power Steering ECU Assembly *d to Combination Meter Assembly
*e to Air Conditioning Amplifier Assembly *f to No. 1 Junction Connector
*g to Radio and Display Receiver Assembly*1 *h to DLC3


Terminal No. (Symbol) Wiring Color Connect to
F83-1 (CANH) P Steering Angle Sensor (Spiral Cable Sub-assembly)
F83-12 (CANL) W
F83-4 (CANH) B Airbag Sensor Assembly
F83-15 (CANL) W
F83-5 (CANH) BE Radio and Display Receiver Assembly*1 or Navigation Receiver Assembly*2
F83-16 (CANL) W
F83-6 (CANH) LG Power Steering ECU Assembly
F83-17 (CANL) W
F83-7 (CANH) G Combination Meter Assembly
F83-18 (CANL) W
F83-8 (CANH) V Air Conditioning Amplifier Assembly
F83-19 (CANL) W
F83-10 (CANH) SB No. 1 Junction Connector
F83-21 (CANL) W
F83-11 (CANH) GR DLC3
F83-22 (CANL) W

*1: for Radio and Display Type

*2: for Navigation Receiver Type




CHECK DLC3


U126783E08
4.229,1.969 4.521,2.344 true 4.292,0.844 3.865,1.375 true 3,0.854 3.427,1.385 true 3.802,1.969 3.521,2.344 true 3.083,2.271 3.531,2.438 0.448,0.167 10 false CANL 4.375,0.75 4.823,0.917 0.448,0.167 10 false CANH 4.604,2.271 4.958,2.438 0.354,0.167 10 false BAT 2.75,0.771 3.104,0.938 0.354,0.167 10 false CG 3.51,0.729 3.802,0.885 0.292,0.156 10 false F4

a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F4-6 (CANH) - F4-14 (CANL) GR - W Ignition switch off 54 to 69 Ω
F4-6 (CANH) - F4-16 (BAT) GR - BE Ignition switch off 6 kΩ or higher
F4-14 (CANL) - F4-16 (BAT) W - BE Ignition switch off 6 kΩ or higher
F4-6 (CANH) - F4-4 (CG) GR - W-B Ignition switch off 200 Ω or higher
F4-14 (CANL) - F4-4 (CG) W - W-B Ignition switch off 200 Ω or higher



CHECK ECM


U135064E06
5.094,1.135 4.833,0.729 true 2.479,1.135 2.219,0.729 true 6.635,1.125 6.448,0.719 true 4.698,2.094 5.094,1.292 true 5.875,0.385 6.292,0.594 0.417,0.208 10 false A83 2.521,0.531 2.917,0.75 0.396,0.219 10 false B89 4.396,0.625 4.979,0.781 0.583,0.156 10 false CANH 4.271,2.031 4.823,2.188 0.552,0.156 10 false CANL 6.229,0.625 6.646,0.781 0.417,0.156 10 false +B 1.99,0.625 2.406,0.781 0.417,0.156 10 false E1

a.

Disconnect the ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A83-13 (CANH) - A83-26 (CANL) L - W Ignition switch off 108 to 132 Ω
A83-13 (CANH) - A83-2 (+B) L - B Ignition switch off 6 kΩ or higher
A83-26 (CANL) - A83-2 (+B) W - B Ignition switch off 6 kΩ or higher
A83-13 (CANH) - B89-16 (E1) L - W-B Ignition switch off 200 Ω or higher
A83-26 (CANL) - B89-16 (E1) W - W-B Ignition switch off 200 Ω or higher



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU), INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (2 Connector Type)


E351568C02
0.25,0.25 0.563,0.406 0.313,0.156 10 false *1 0.917,6.75 1.229,6.906 0.313,0.156 10 false *2 0.927,0.938 1.24,1.135 0.313,0.198 10 false 3D 0.917,1.573 1.229,1.771 0.313,0.198 10 false 3C 0.927,2.104 1.24,2.302 0.313,0.198 10 false 3F 6.375,0.979 6.688,1.177 0.313,0.198 10 false 3B 6.375,1.604 6.688,1.802 0.313,0.198 10 false 3A 3.792,0.802 4.104,1 0.313,0.198 10 false MB 3.667,2.885 3.979,3.083 0.313,0.198 10 false MB 6.083,3.854 6.396,4.052 0.313,0.198 10 false 3F 3.969,3.854 4.281,4.052 0.313,0.198 10 false 3C 1.458,3.854 1.771,4.052 0.313,0.198 10 false 3D 1.615,5.24 1.927,5.438 0.313,0.198 10 false 3B 5.375,5.24 5.688,5.438 0.313,0.198 10 false 3A 3.729,6.458 4.188,6.656 0.458,0.198 10 false F76 2.896,6.458 3.51,6.656 0.615,0.198 10 false F136 2.458,7.5 3.073,7.698 0.615,0.198 10 false F136 4.823,7.49 5.281,7.688 0.458,0.198 10 false F76
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Disconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F76-14 (CANH) - F76-13 (CANL) R - W Ignition switch off 54 to 69 Ω
F76-14 (CANH) - 3C-21 R - L Ignition switch off 6 kΩ or higher
F76-13 (CANL) - 3C-21 W - L Ignition switch off 6 kΩ or higher
F76-14 (CANH) - 3B-8 R - W-B Ignition switch off 200 Ω or higher
F76-13 (CANL) - 3B-8 W - W-B Ignition switch off 200 Ω or higher



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU), INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (1 Connector Type)


E351569C02
0.167,0.167 0.479,0.323 0.313,0.156 10 false *1 1.25,6.75 1.563,6.906 0.313,0.156 10 false *2 3.802,0.792 4.115,0.99 0.313,0.198 10 false MB 3.802,2.865 4.115,3.063 0.313,0.198 10 false MB 0.938,0.906 1.25,1.104 0.313,0.198 10 false 3D 0.938,1.51 1.25,1.708 0.313,0.198 10 false 3C 0.948,2.135 1.26,2.333 0.313,0.198 10 false 3F 1.521,3.854 1.833,4.052 0.313,0.198 10 false 3D 6.5,0.906 6.813,1.104 0.313,0.198 10 false 3B 6.5,1.51 6.813,1.708 0.313,0.198 10 false 3A 3.99,3.854 4.302,4.052 0.313,0.198 10 false 3C 6.094,3.885 6.406,4.083 0.313,0.198 10 false 3F 5.49,5.208 5.802,5.406 0.313,0.198 10 false 3A 1.635,5.219 1.948,5.417 0.313,0.198 10 false 3B 3.802,6.458 4.26,6.656 0.458,0.198 10 false F76 3.708,7.531 4.167,7.729 0.458,0.198 10 false F76
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Disconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F76-14 (CANH) - F76-13 (CANL) R - W Ignition switch off 54 to 69 Ω
F76-14 (CANH) - 3C-21 R - L Ignition switch off 6 kΩ or higher
F76-13 (CANL) - 3C-21 W - L Ignition switch off 6 kΩ or higher
F76-14 (CANH) - 3B-8 R - W-B Ignition switch off 200 Ω or higher
F76-13 (CANL) - 3B-8 W - W-B Ignition switch off 200 Ω or higher



CHECK COMBINATION METER ASSEMBLY


U127243E05
4.323,1.156 4.063,1.552 true 3.385,1.146 3.125,1.542 true 4.479,1.146 4.74,1.542 true 5.646,1.146 5.906,1.542 true 4.458,0.333 4.75,0.49 0.292,0.156 10 false F1 3.625,1.458 4.177,1.615 0.552,0.156 10 false CANH 4.792,1.458 5.323,1.615 0.531,0.156 10 false CANL 2.979,1.458 3.229,1.615 0.25,0.156 10 false B 5.948,1.458 6.156,1.615 0.208,0.156 10 false ET

a.

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F1-32 (CANH) - F1-31 (CANL) G - W Ignition switch off 108 to 132 Ω
F1-32 (CANH) - F1-40 (B) G - L Ignition switch off 6 kΩ or higher
F1-31 (CANL) - F1-40 (B) W - L Ignition switch off 6 kΩ or higher
F1-32 (CANH) - F1-21 (ET) G - BR Ignition switch off 200 Ω or higher
F1-31 (CANL) - F1-21 (ET) W - BR Ignition switch off 200 Ω or higher



CHECK SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)


U158732E04
4.073,1.823 4.333,2.219 true 4.573,0.854 4.313,1.25 true 2.781,1.24 2.521,0.833 true 4.729,1.448 4.083,1.594 true 3.417,0.594 3.708,0.75 0.292,0.156 10 false A54 4.396,2.167 4.958,2.323 0.563,0.156 10 false CANH 4.781,1.365 5.323,1.521 0.542,0.156 10 false CANL 4.625,0.771 5.042,0.927 0.417,0.156 10 false GND1 2.208,0.771 2.625,0.927 0.417,0.156 10 false +BS

a.

Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A54-25 (CANH) - A54-14 (CANL) G - W Ignition switch off 54 to 69 Ω
A54-25 (CANH) - A54-12 (+BS) G - W Ignition switch off 6 kΩ or higher
A54-14 (CANL) - A54-12 (+BS) W - W Ignition switch off 6 kΩ or higher
A54-25 (CANH) - A54-1 (GND1) G - W-B Ignition switch off 200 Ω or higher
A54-14 (CANL) - A54-1 (GND1) W - W-B Ignition switch off 200 Ω or higher



CHECK AIRBAG SENSOR ASSEMBLY


U158733E03
2.844,1.563 2.188,2.219 true 3.021,1.823 3.396,2.208 true 6.604,1.74 6.219,2.115 true 5.594,0.885 5.969,1.26 true 1.729,2.167 2.24,2.396 0.51,0.229 10 false CANH 3.448,2.146 3.948,2.354 0.5,0.208 10 false CANL 2.354,0.625 2.635,0.781 0.281,0.156 10 false F16 5.938,2.073 6.292,2.292 0.354,0.219 10 false BAT 5.344,0.813 5.76,1.01 0.417,0.198 10 false CG 5.969,0.719 6.219,0.875 0.25,0.156 10 false F4

a.

Disconnect the airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F16-13 (CANH) - F16-22 (CANL) B - W Ignition switch off 54 to 69 Ω
F16-13 (CANH) - F4-16 (BAT) B - BE Ignition switch off 6 kΩ or higher
F16-22 (CANL) - F4-16 (BAT) W - BE Ignition switch off 6 kΩ or higher
F16-13 (CANH) - F4-4 (CG) B - W-B Ignition switch off 200 Ω or higher
F16-22 (CANL) - F4-4 (CG) W - W-B Ignition switch off 200 Ω or higher



CHECK STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)


U127162E05
3.448,1.76 3.167,2.365 true 3.833,1.771 4.115,2.375 true 4.104,1.771 4.875,2.365 true 2.948,1.771 2.177,2.365 true 2.719,2.26 3.26,2.406 0.542,0.146 10 false CANH 4.188,2.271 4.708,2.51 0.521,0.24 10 false CANL 4.948,2.26 5.313,2.458 0.365,0.198 10 false ESS 1.844,2.26 2.135,2.406 0.292,0.146 10 false BAT 3.521,0.542 3.813,0.698 0.292,0.156 10 false F30

a.

Disconnect the steering angle sensor (spiral cable sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F30-4 (CANH) - F30-3 (CANL) P - W Ignition switch off 54 to 69 Ω
F30-4 (CANH) - F30-6 (BAT) P - SB Ignition switch off 6 kΩ or higher
F30-3 (CANL) - F30-6 (BAT) W - SB Ignition switch off 6 kΩ or higher
F30-4 (CANH) - F30-2 (ESS) P - BR Ignition switch off 200 Ω or higher
F30-3 (CANL) - F30-2 (ESS) W - BR Ignition switch off 200 Ω or higher



CHECK POWER STEERING ECU ASSEMBLY


U126895E04
5.01,1.594 5.563,2.281 true 4.26,1.594 3.688,2.281 true 2.104,1.552 2.656,2.25 true 1.979,1.552 1.417,2.25 true 4.531,0.729 4.823,0.885 0.292,0.156 10 false A42 5.635,2.177 5.927,2.333 0.292,0.156 10 false PIG 3.229,2.177 3.667,2.333 0.438,0.156 10 false PGND 2.729,2.135 3.167,2.292 0.438,0.156 10 false CANH 0.979,2.146 1.417,2.302 0.438,0.156 10 false CANL 2.052,0.74 2.344,0.896 0.292,0.156 10 false F6

a.

Disconnect the power steering ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F6-7 (CANH) - F6-8 (CANL) LG - W Ignition switch off 54 to 69 Ω
F6-7 (CANH) - A42-1 (PIG) LG - W Ignition switch off 6 kΩ or higher
F6-8 (CANL) - A42-1 (PIG) W - W Ignition switch off 6 kΩ or higher
F6-7 (CANH) - A42-2 (PGND) LG - W-B Ignition switch off 200 Ω or higher
F6-8 (CANL) - A42-2 (PGND) W - W-B Ignition switch off 200 Ω or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


U127350C02
3.031,0.74 2.771,0.344 true 4.677,1.385 4.417,0.99 true 3.146,0.729 3.406,0.333 true 5.354,2.677 5.594,2.302 true 2.448,1.302 2.75,0.823 true 1.094,2.656 1.396,2.188 true 1.344,1.969 1.083,1.573 true 1.49,1.969 1.75,1.573 true 1.063,0.74 1.375,0.948 0.313,0.208 10 false F42 0.219,2.031 0.51,2.188 0.292,0.156 10 false F41 3.99,2.031 4.281,2.188 0.292,0.156 10 false F4 1.438,0.75 1.729,0.906 0.292,0.156 10 false *A 0.573,2.021 0.865,2.177 0.292,0.156 10 false *B 3.448,0.219 3.875,0.385 0.427,0.167 10 false TX+ 2.51,0.24 2.938,0.417 0.427,0.177 10 false TX- 2.135,1.25 2.552,1.406 0.417,0.156 10 false GND 4.74,1.333 5.156,1.49 0.417,0.156 10 false B 5.073,2.583 5.49,2.74 0.417,0.156 10 false BAT 0.771,2.563 1.188,2.719 0.417,0.156 10 false GND 1.802,1.438 2.219,1.594 0.417,0.156 10 false TX+ 0.844,1.448 1.26,1.604 0.417,0.156 10 false TX-
*A for Automatic Air Conditioning System *B for Manual Air Conditioning System


a.

Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F42-11 (TX+) - F42-12 (TX-)*1
F41-8 (TX+) - F41-9 (TX-)*2
V - W Ignition switch off 54 to 69 Ω
F42-11 (TX+) - F42-21 (B)*1
F41-8 (TX+) - F4-16 (BAT)*2
V - BE Ignition switch off 6 kΩ or higher
F42-12 (TX-) - F42-21 (B)*1
F41-9 (TX-) - F4-16 (BAT)*2
W - BE Ignition switch off 6 kΩ or higher
F42-11 (TX+) - F42-14 (GND)*1
F41-8 (TX+) - F41-23 (GND)*2
V - W-B Ignition switch off 200 Ω or higher
F42-12 (TX-) - F42-14 (GND)*1
F41-9 (TX-) - F41-23 (GND)*2
W - W-B Ignition switch off 200 Ω or higher

*1: for Automatic Air Conditioning System

*2: for Manual Air Conditioning System




CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


U158739E05
4.271,1.448 4.604,0.948 true 4.771,0.948 4.99,1.479 true 2.052,1.135 2.188,1.5 true 1.521,0.938 1.104,1.458 true 1.781,0.271 2.125,0.427 0.344,0.156 10 false F125 4.781,0.271 5.125,0.427 0.344,0.156 10 false F127 2.063,1.5 2.635,1.677 0.573,0.177 10 false GND1 4.865,1.5 5.458,1.635 0.594,0.135 10 false CANH 4.052,1.5 4.646,1.635 0.594,0.135 10 false CANL 0.938,1.5 1.302,1.635 0.365,0.135 10 false +B1

a.

Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F127-9 (CANH) - F127-10 (CANL) BE - W Ignition switch off 54 to 69 Ω
F127-9 (CANH) - F125-4 (+B1) BE - SB Ignition switch off 6 kΩ or higher
F127-10 (CANL) - F125-4 (+B1) W - SB Ignition switch off 6 kΩ or higher
F127-9 (CANH) - F125-7 (GND1) BE - BR Ignition switch off 200 Ω or higher
F127-10 (CANL) - F125-7 (GND1) W - BR Ignition switch off 200 Ω or higher



CHECK NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


U158740E05
4.281,1.448 4.615,0.948 true 4.76,0.948 4.979,1.479 true 2.052,1.135 2.188,1.5 true 1.51,0.938 1.094,1.458 true 1.781,0.271 2.125,0.427 0.344,0.156 10 false F130 4.781,0.271 5.125,0.427 0.344,0.156 10 false F132 2.042,1.5 2.604,1.698 0.563,0.198 10 false GND1 4.865,1.5 5.458,1.635 0.594,0.135 10 false CANH 4.052,1.5 4.646,1.635 0.594,0.135 10 false CANL 0.938,1.5 1.302,1.635 0.365,0.135 10 false +B1

a.

Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F132-9 (CANH) - F132-10 (CANL) BE - W Ignition switch off 54 to 69 Ω
F132-9 (CANH) - F130-4 (+B1) BE - SB Ignition switch off 6 kΩ or higher
F132-10 (CANL) - F130-4 (+B1) W - SB Ignition switch off 6 kΩ or higher
F132-9 (CANH) - F130-7 (GND1) BE - BR Ignition switch off 200 Ω or higher
F132-10 (CANL) - F130-7 (GND1) W - BR Ignition switch off 200 Ω or higher



Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION