Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) L

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  PRECAUTION  


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


STEERING SYSTEM HANDLING PRECAUTIONS


a.

Care must be taken when replacing parts. Incorrect replacement could affect the performance of the steering system and result in hazards when driving.



SRS AIRBAG SYSTEM HANDLING PRECAUTIONS


a.

This vehicle is equipped with an SRS (Supplemental Restraint System), which includes components such as the driver airbag and front passenger airbag. Failure to carry out service operations in the correct sequence could cause unexpected SRS deployment during servicing and may lead to a serious accident. Before servicing (including installation/removal, inspection and replacement of parts), be sure to read the precautionary notice for the Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>PRECAUTION).



BUS LINE REPAIR


a.
E120441

After repairing the bus line with solder, wrap the repaired part with vinyl tape (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

NOTICE:
·

The CANL bus line and CANH bus line must be installed together.

·

When installing the CAN bus lines, be sure to twist them.

·

CAN bus lines are likely to be influenced by noise if the bus lines are not twisted together.

·

Leave approximately 80 mm (3.15 in.) loose in the twisted wires around the connectors.

·

When repairing the CAN bus lines, do not change the length of the lines. (Make sure that the length of the CANH bus line and CANL bus line are the same.)




b.
E134624E03
1.497,0.511 1.669,0.678 0.172,0.167 10 *1 1.707,0.605 1.85,0.605 1.85,0.605 2.053,1.03 false

Do not use by-pass wiring between the connectors.

NOTICE:

The protective effect of the twisted wire harness is lost if bypass wiring is used.


Text in Illustration
*1 By-pass Wire



CONNECTOR HANDLING


a.
E120443E02
1.068,1.521 1.273,1.688 0.205,0.168 10 *1 1.805,1.217 1.325,1.603 1.325,1.603 1.537,1.544 false

When inserting probes into a connector, insert them from the rear of the connector.

Text in Illustration
*1 Tester Probe


b.
E120444E02
1.979,0.515 2.162,0.680 0.183,0.164 10 *1 1.453,0.917 1.873,0.596 1.873,0.596 1.528,1.297 false 1.873,0.596 1.955,0.596 false

Use a repair wire to check the connector if it is impossible to check resistance from the rear of the connector.

Text in Illustration
*1 Repair Wire



PRECAUTIONS FOR INSPECTING OR REPLACING CAN JUNCTION CONNECTOR


a.

If the CAN junction connector is removed from the vehicle for inspection or replacement, make sure to install the CAN junction connector and all wire harnesses to their original locations with tape and the clamps.



PRECAUTIONS WHEN REPLACING A GATEWAY FUNCTION EQUIPPED ECU (CENTRAL GATEWAY ECU OR SUB BUS MONITOR ECU) WITH A USED ONE FROM ANOTHER VEHICLE


a.

When a gateway function equipped ECU (central gateway ECU (network gateway ECU)) that was previously installed on another vehicle is used as a replacement part, it is necessary to initialize the connection information stored in the ECU.

NOTICE:

If the connection information stored in a gateway function equipped ECU that was previously installed on another vehicle is different from the actual ECUs and sensors connected to the corresponding bus, communication DTCs will be detected.


HINT:

When an ECU is replaced with one from a vehicle with the same options and specifications (the same connections to the corresponding bus), initialization of ECU connection information is not necessary.



b.

Initialize the connection information of gateway function equipped ECU (central gateway ECU (network gateway ECU)).


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch ON.


e.

Turn the GTS on.


f.

Enter the following menus: Body Electrical / Central Gateway / Utility


g.

Select Initialization from Utility to initialize the ECU.



PRECAUTIONS WHEN GATEWAY FUNCTION EQUIPPED ECU (CENTRAL GATEWAY ECU OR SUB BUS MONITOR ECU) DETECTS COMMUNICATION DTCS FOR ECUS NOT CONNECTED TO THE ECU


a.

Refer to Precautions When Replacing Gateway Function Equipped ECU (central gateway ECU (network gateway ECU)) with a Used One from Another Vehicle and initialize the connection information of the ECU.


b.

Clear the DTCs and check that no DTCs are output.