FAIL-SAFE FUNCTION
When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.
The table below shows the effects on each system when communication is impossible. For further details, refer to each system.
| System | Function
(Function Description) |
Control Master | System Related | Fail-safe Operation | DTC
(Driver Detectable) |
|---|---|---|---|---|---|
| Central Gateway ECU | Communication interruption detection | Central gateway ECU (network gateway ECU) | ECUs connected to global bus | Time when communication was interrupted is recorded. | Nothing
(Nothing) |
| Engine | Electrical load control | ECM | Power steering ECU assembly | The idle speed increase for an electrical load is not performed. | Nothing
(The idle speed changes.) |
| Engine | Air conditioner-linked control | ECM | Air conditioning amplifier assembly | Air conditioner-linked control does not operate. (cannot idle up) | Nothing
(Air conditioning inoperative.) |
| Engine | PTC heater | ECM | Air conditioning amplifier assembly | PTC heater does not operate. (does not permit operations) | Nothing
(The idle speed changes. The heater function worsens. PTC heater does not operate.) |
| Engine | Charging control | ECM | Air conditioning amplifier assembly, Main body ECU (multiplex network body ECU) | The idle speed increase for a charge request is not performed. | Nothing
(The idle speed increase for a charge request is not performed.) |
| Charge control is not prohibited. | Nothing
(Tail lights flicker and blower airflow changes.) |
||||
| Engine | Integrated control | ECM | Skid control ECU (brake actuator assembly), Power steering ECU assembly | Following performances are not operative: Stable constant-speed drivability, starting ability, re-acceleration ability and improved feeling of acceleration by estimating the required torque from the driver's accelerator pedal control and performing torque control according to the driving situation. | Nothing
(Following performances are not operative: Stable constant-speed drivability, starting ability, re-acceleration ability and improved feeling of acceleration by estimating the required torque from the driver's accelerator pedal control and performing torque control according to the driving situation.) |
| Engine | Neutral Control | ECM | Skid control ECU (brake actuator assembly) | Neutral control does not operate. | U0129
(Nothing) |
| Engine | Cruise control | ECM | Skid control ECU (brake actuator assembly), Combination meter assembly | Nothing | Nothing
(Indicator light blink.) |
| Engine | Pre-crash safety system | ECM | Pre-crash safety city sensor | During pre-crash safety operation, the accelerator opening angle does not fully close. | Nothing
(Pre-crash safety system does not operate.) |
| Airbag | Event Recorder | Airbag sensor assembly | ECM, Skid control ECU (brake actuator assembly | An invalid value is stored | Nothing
(Nothing) |
| VSC | ABS control | Skid control ECU (brake actuator assembly) | Airbag sensor assembly | ·
During control: After ending backup control (stabilizing the vehicle), the system changes to normal braking and prohibits control. ·
Not during control: Control cannot start. |
U0073, U0124
(Brake warning light comes on. ABS warning light comes on. Slip indicator light comes on.) |
| VSC | VSC control | Skid control ECU (brake actuator assembly) | ECM, Steering angle sensor (spiral cable sub-assembly), Airbag sensor assembly | ·
During control: After ending backup control (stabilizing the vehicle), the system changes to normal braking and prohibits control. ·
Not during control: Control cannot start. |
U0073, U0100, U0124, U0126
(Brake warning light comes on. ABS warning light comes on. Slip indicator light comes on.) |
| VSC | Hill-start assist control 3 | Skid control ECU (brake actuator assembly) | ECM, Steering angle sensor (spiral cable sub-assembly), Airbag sensor assembly | ·
During control: After ending backup control (pressure reduction control), the system changes to normal braking and prohibits control, or control continues, and after normal control finishes, prohibits control. ·
Not during control: Control cannot start. |
U0073, U0100, U0124, U0126
(Brake warning light comes on. ABS warning light comes on. Slip indicator light comes on.) |
| Air Conditioning | Air conditioning control | Air Conditioning Amplifier Assembly | ECM | ·
Coolant signal during the ignition switch ON: Controlled with default value of 80°C. ·
Engine model during the ignition switch ON: Controlled with default value which differs according to vehicle models. ·
Not controlled without the ignition switch ON. |
U0100
(Nothing) |
| Air Conditioning | Compressor control | Air Conditioning Amplifier Assembly | ECM | ·
Control is performed based on default engine speed of 0 rpm. ·
Not controlled without the ignition switch ON. |
U0100
(Nothing) |
| Air Conditioning | Simple load control | Air Conditioning Amplifier Assembly | Power steering ECU assembly | ·
Previous status held during the ignition switch ON. (when resetting: no load control.) ·
Not controlled without the ignition switch ON. |
U0131
(Nothing) |
| Air Conditioning | Panel dimming control | Air Conditioning Amplifier Assembly | Main body ECU (multiplex network body ECU) | ·
Previous status held during the ignition switch ON. (when resetting: no load control.) ·
Not controlled without the ignition switch ON. |
U0142
(Cannot switch between dimming and not dimming (after resetting, dimming status remains), Not IG-ON: Nothing.) |
| Air Conditioning | Destination determinate control | Air Conditioning Amplifier Assembly | Main body ECU (multiplex network body ECU) | ·
Previous status held during the ignition switch ON. ·
Not controlled without the ignition switch ON. |
U0142
(Nothing) |
| Air Conditioning | External temperature compensation control | Air Conditioning Amplifier Assembly | Combination meter assembly | ·
Speed signal input during the ignition switch ON : Controlled with the default value of 0 km/h. ·
Not controlled without the ignition switch ON. |
U0155
(The matching reliability of the displayed external temperature to the actual external temperature is deteriorated. The suitability level of air conditioner outlet airflow compensation is reduced.) |
| Radio and Display | Air Conditioning Control | Radio and display receiver assembly (for Radio and Display Type) or Navigation receiver assembly (for Navigation Receiver Type) | Air conditioning amplifier assembly | ·
Air conditioning system indicators turn off. ·
If set temperature is shown on combination meter assembly, set temperature display turns off. ·
Air conditioning function(s) are prohibited. |
U0073, U0164
(Displays messages on the multi-information display.) |
| Radio and Display | Fuel Consumption Display | Radio and display receiver assembly (for Radio and Display Type) or Navigation receiver assembly (for Navigation Receiver Type) | ECM, Skid control ECU (brake actuator assembly), Combination meter assembly | ·
Updating of average per minute fuel consumption is stopped. (The graph of average per minute fuel consumption history displayed to that point is not deleted.) ·
Updating of current aggregated fuel consumption is stopped. ·
When the cruising range is displayed, the numerical part of the cruising range is deleted due to a communication interruption. |
U0100, U0129, U0155
(The graph of average per minute fuel consumption is not updated. Most recent value in the graph of average per minute fuel consumption is deleted. In the graph of average per minute fuel consumption, the numerical part of the cruising range is deleted.) |
| Radio and Display | Vehicle Customization Function | Radio and display receiver assembly (for Radio and Display Type) or Navigation receiver assembly (for Navigation Receiver Type) | Main body ECU (multiplex network body ECU), Air conditioning amplifier assembly, Combination meter assembly | When an application that uses phase 4 remote communication is activated (customization/remote diagnosis), the process will be performed regardless of main body ECU (multiplex network body ECU) remote communication permit/ prohibit state. | Nothing
(Related customization items are not displayed or do not change to set values.) |
| Radio and Display | Time Stamp Function | Radio and display receiver assembly (for Radio and Display Type) or Navigation receiver assembly (for Navigation Receiver Type) | Main body ECU (multiplex network body ECU) | Nothing | U0073, U0140
(Nothing) |
| Radio and Display | Rear View Monitor System | Radio and display receiver assembly (for Radio and Display Type) or Navigation receiver assembly (for Navigation Receiver Type) | ECM | Nothing | U0100
(Screen does not change to the camera screen.) |
| Main body | Automatic Dimming of Display | Main body ECU (multiplex network body ECU) | Combination meter assembly | ·
Conduct the display auto dimming control without the tail cancel status. ·
If the light sensor illumination signal value is less than the display dimming value, the in-room displays and indicators are dimmed. |
U0155
(Nothing) |
| Main body | Illumination | Main body ECU (multiplex network body ECU) | ECM | ·
The dome light is turned off. ·
The interior foot light illumination is turned off. |
U0100, U0101
(The dome light is not turned off immediately after the vehicle is left.) |
| Main body | Lighting control (DRL control) | Main body ECU (multiplex network body ECU) | ECM | DRL control operation fails. | Nothing
(Detected by failure of DRL control.) |
| Main body | Automatic high beam | Main body ECU (multiplex network body ECU) | Pre-crash safety city sensor | Automatic high beam is not possible (Automatic high beam warning light blinks). | U023A
(Automatic high beam indicator light flashes.) |
| EPS | Electronic power steering system | Power steering ECU assembly | ECM, Steering angle sensor (spiral cable sub-assembly), Airbag sensor assembly, Skid control ECU (brake actuator assembly) | ·
Electronic power steering does not operate. ·
Steering assistance is temporarily restricted. ·
Zero point learning is not performed. ·
The steering feel becomes worse (compensation control using the steering angle is stopped). |
U0100, U0129
(EPS indicator light comes on.) |
| EPS | DTC output | Combination meter assembly | ECM, Power steering ECU assembly | Nothing | Nothing
(Nothing) |
| EPS | Assist map selection | Power steering ECU assembly | Main body ECU (multiplex network body ECU), ECM, Skid control ECU (brake actuator assembly) | ·
An assist mapping corresponding to the vehicle cannot be selected, so assist is performed using a preliminary map. ·
The vehicle's steering may feel abnormal. ·
The frame used for assist map selection may change from vehicle to vehicle. |
C1581
(EPS indicator light comes on.) |
| EPS | Warning light illumination | Combination meter assembly | Power steering ECU assembly | Nothing | Nothing
(Nothing) |
| EPS | ECE79 | Power steering ECU assembly | - | Nothing | Nothing
(Nothing) |
| Combination meter | Vehicle speed indication
(speedometer display for vehicle speed signal from skid control ECU (brake actuator assembly)) |
Combination meter assembly | Skid control ECU (brake actuator assembly) (w/ VSC) | Signal is treated as 0. | U0129
(Vehicle speed on the meter is indicated as 0 km/h. Drive monitor calculation stops.) |
| Combination meter | Tachometer | Combination meter assembly | ECM | Signal is treated as 0. | U0100
(Tachometer rpm displayed as 0 rpm. Drive monitor calculation stops.) |
| Combination meter | Airbag
(Airbag warning ON/OFF) |
Combination meter assembly | Airbag sensor assembly | Signal is treated as active. | U0151
(Warning light comes on.) |
| Combination meter | EPS warning | Combination meter assembly | Power steering ECU assembly | Signal is treated as active. | U0131
(Warning light comes on.) |
| Combination meter | Slip warning | Combination meter assembly | Skid control ECU (brake actuator assembly) (w/ VSC) | Signal is treated as active. | Nothing
(Indicator light comes on.) |
| Combination meter | Automatic high beam indicator | Combination meter assembly | Main body ECU (Multiplex network body ECU) | Keep the last signal state until ignition switch off. | Nothing
(Nothing) |
| Combination meter | PCS warning | Combination meter assembly | Pre-crash safety city sensor | PCS warning light flashes. | U023A
(PCS warning light flashes.) |
| Combination meter | PCS warning | Combination meter assembly | Pre-crash safety city sensor | Keep the last signal state until ignition switch off. | U023A
(Nothing) |
| Combination meter | PCS option judgment | Combination meter assembly | Pre-crash safety city sensor | Keep the last signal state until ignition switch off. | U023A
(Nothing) |
| Combination meter | PCS sensitivity display | Combination meter assembly | Pre-crash safety city sensor | Keep the last signal state until ignition switch off. | U023A
(Nothing) |
| Combination meter | Pre-crash safety warning buzzer | Combination meter assembly | Pre-crash safety city sensor | Keep the last signal state until ignition switch off. | U023A
(Nothing) |
| Combination meter | LDA option judgment | Combination meter assembly | Pre-crash safety city sensor | Keep the last signal state until ignition switch off. | U023A
(Nothing) |
| Combination meter | Lane departure alert warning buzzer | Combination meter assembly | Pre-crash safety city sensor | Lane departure alert warning buzzer is canceled. | U023A
(Lane departure alert warning buzzer does not sound.) |
| Pre-crash safety city sensor | Pre-crash safety system | Pre-crash safety city sensor | Skid control ECU (brake actuator assembly), airbag sensor assembly, steering angle sensor (spiral cable sub-assembly), ECM and combination meter assembly | Control stops. | U0100, U0123, U0126, U0129 and U023A
(Pre-crash safety warning buzzer sounds. PCS warning light flashes.) |
| Pre-crash safety city sensor | Lane departure alert system | Pre-crash safety city sensor | Skid control ECU (brake actuator assembly), ECM, steering angle sensor (spiral cable sub-assembly), airbag sensor assembly, and combination meter assembly | Control stops. | U0100, U0123, U0126, U0129 and U0155
(LDA indicator light illuminates (yellow).) |