Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either condition is met:
·

Communication stop for "Air Conditioning Amplifier" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" are output.

(Click here)


·

Power source or inside Air conditioning amplifier assembly

·

Air conditioning amplifier assembly branch wire or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E226967E10
1.448,1.042 1.875,1.208 0.427,0.167 10 false CANH 1.448,1.49 1.875,1.656 0.427,0.167 10 false CANL 0.563,1.958 0.969,2.125 0.406,0.167 10 false F83 4.521,0.865 4.833,1.031 0.313,0.167 10 false 11*1 5.281,1.052 5.76,1.25 0.479,0.198 10 false CANH 5.281,1.5 5.729,1.698 0.448,0.198 10 false CANL 1.938,2.802 3.313,3.115 1.375,0.313 10 false from IG1 NO. 1 Relay 3.885,2.938 4.156,3.104 0.271,0.167 10 false A/C 5.281,3.24 5.708,3.406 0.427,0.167 10 false GND 4.521,1.313 4.833,1.479 0.313,0.167 10 false 12*1 1.948,1.406 2.125,1.573 0.177,0.167 10 false 19 1.969,0.958 2.146,1.125 0.177,0.167 10 false 8 5.281,2.792 5.708,2.958 0.427,0.167 10 false IG+ 4.552,2.604 4.844,2.771 0.292,0.167 10 false 1*1 4.51,3.052 4.833,3.219 0.323,0.167 10 false 14*1 4.927,0.865 5.24,1.031 0.313,0.167 10 false 8*2 4.927,1.313 5.24,1.479 0.313,0.167 10 false 9*2 4.927,2.625 5.219,2.792 0.292,0.167 10 false 1*2 4.885,3.052 5.208,3.219 0.323,0.167 10 false 23*2 4.927,1.052 5.188,1.219 0.26,0.167 10 false F41 4.552,1.042 4.813,1.208 0.26,0.167 10 false F42 4.552,1.51 4.813,1.677 0.26,0.167 10 false F42 4.552,2.792 4.813,2.958 0.26,0.167 10 false F42 4.552,3.24 4.813,3.406 0.26,0.167 10 false F42 4.927,1.531 5.188,1.698 0.26,0.167 10 false F41 4.927,2.781 5.188,2.948 0.26,0.167 10 false F41 2.26,2.344 3.313,2.656 1.052,0.313 10 false from MAIN Fuse 3.583,2.521 4.448,2.688 0.865,0.167 10 false ECU-B NO. 2 5.281,2.333 5.708,2.5 0.427,0.167 10 false B 4.906,2.146 5.219,2.313 0.313,0.167 10 false 21*1 4.927,2.333 5.188,2.5 0.26,0.167 10 false F42 4.927,3.24 5.188,3.406 0.26,0.167 10 false F41 0.552,2.146 2.167,2.469 1.615,0.323 10 false No. 2 Junction Connector 0.073,4.354 3.604,4.677 3.531,0.323 10 false *2 : for Manual Air Conditioning System 0.073,4.042 2.677,4.365 2.604,0.323 10 false *1 : for Automatic Air Conditioning System 4.573,3.906 6.823,4.552 2.25,0.646 10 false Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.
U127247C03
1.74,0.854 1.417,0.365 true 1.958,0.854 2.271,0.365 true 2.542,2.24 2.354,1.76 true 2.75,2.24 2.969,1.75 true 1.552,0.104 1.917,0.281 0.365,0.177 10 false F42 0.104,0.104 0.396,0.26 0.292,0.156 10 false *a 0.104,1.583 0.396,1.74 0.292,0.156 10 false *b 1.552,1.542 1.906,1.719 0.354,0.177 10 false F41 1,0.229 1.448,0.417 0.448,0.188 10 false CANH 2.323,0.229 2.802,0.417 0.479,0.188 10 false CANL 1.948,1.604 2.396,1.802 0.448,0.198 10 false CANH 3.01,1.594 3.417,1.771 0.406,0.177 10 false CANL
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System))
*b Front view of wire harness connector
(to Air Conditioning Amplifier Assembly (for Manual Air Conditioning System))


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F42-11 (CANH) - F42-12 (CANL)*1
F41-8 (CANH) - F41-9 (CANL)*2
Ignition switch off 54 to 69 Ω



*1 : for Automatic Air Conditioning System

*2 : for Manual Air Conditioning System


OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
U127248C01
0.521,0.854 0.844,0.365 true 0.844,1.51 0.521,1.115 true 2.167,0.854 2.479,0.365 true 2.448,3.021 2.656,2.531 true 0.635,2.24 0.844,1.75 true 1.552,0.115 1.844,0.271 0.292,0.156 10 false F42 0.104,0.083 0.396,0.24 0.292,0.156 10 false *a 0.104,1.563 0.396,1.719 0.292,0.156 10 false *b 1.563,1.542 1.854,1.698 0.292,0.156 10 false F41 0.917,0.24 1.333,0.396 0.417,0.156 10 false IG+ 0.896,1.427 1.313,1.583 0.417,0.156 10 false B 2.531,0.229 2.948,0.385 0.417,0.156 10 false GND 2.135,2.979 2.469,3.135 0.333,0.156 10 false GND 0.917,1.635 1.188,1.792 0.271,0.156 10 false IG+
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System))
*b Front view of wire harness connector
(to Air Conditioning Amplifier Assembly (for Manual Air Conditioning))


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F42-1 (IG+) - Body ground*1
F41-1 (IG+) - Body ground*2
Ignition switch ON 11 to 14 V
F42-21 (B) - Body ground*1 Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F42-14 (GND) - Body ground*1
F41-23 (GND) - Body ground*2
Always Below 1 Ω



*1 : for Automatic Air Conditioning System

*2 : for Manual Air Conditioning System


OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)