Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Power Steering (EPS)" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table" are output.

(Click here)


·

Power source or inside power steering ECU assembly

·

Power steering ECU assembly branch wire or connector

·

Power steering ECU assembly



WIRING DIAGRAM

E351557E01
1.479,1.083 2.094,1.281 0.615,0.198 10 false CANH 1.479,1.521 2.094,1.719 0.615,0.198 10 false CANL 2,0.979 2.615,1.177 0.615,0.198 10 false 6 2,1.427 2.615,1.625 0.615,0.198 10 false 17 0.583,1.979 1.198,2.177 0.615,0.198 10 false F83 0.583,2.135 2.219,2.479 1.635,0.344 10 false No. 2 Junction Connector 5,1.073 5.24,1.271 0.24,0.198 10 false F6 5.333,1.073 5.948,1.271 0.615,0.198 10 false CANH 5.333,1.531 5.948,1.729 0.615,0.198 10 false CANL 4.948,2.115 5.25,2.323 0.302,0.208 10 false A42 5,1.531 5.26,1.708 0.26,0.177 10 false F6 5,2.573 5.271,2.771 0.271,0.198 10 false F6 4.948,3.271 5.271,3.458 0.323,0.188 10 false A42 5.333,2.115 5.948,2.313 0.615,0.198 10 false PIG 5.333,2.573 5.948,2.771 0.615,0.198 10 false IG 5.333,3.271 5.948,3.469 0.615,0.198 10 false PGND 5.031,0.885 5.271,1.083 0.24,0.198 10 false 7 5.031,1.333 5.271,1.531 0.24,0.198 10 false 8 5.031,1.927 5.271,2.125 0.24,0.198 10 false 1 5.031,2.385 5.271,2.583 0.24,0.198 10 false 1 5.031,3.073 5.271,3.271 0.24,0.198 10 false 2 5.25,3.906 6.24,4.406 0.99,0.5 10 false Power Steering ECU Assembly 3.823,2.292 4.26,2.479 0.438,0.188 10 false EPS 3.615,2.729 4.51,2.979 0.896,0.25 10 false ECU-IG NO.1 2.385,2.125 3.49,2.396 1.104,0.271 10 false from ALT Fuse 1.938,2.583 3.458,2.906 1.521,0.323 10 false from IG1 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY BRANCH WIRE)
a.
U127246C02
1.698,1.094 2.021,1.583 true 1.521,1.094 1.198,1.583 true 1.625,0.083 1.917,0.24 0.292,0.156 10 false F6 0.104,0.063 0.396,0.219 0.292,0.156 10 false *a 2.094,1.479 2.615,1.677 0.521,0.198 10 false CANH 0.76,1.479 1.177,1.635 0.417,0.156 10 false CANL
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F6-7 (CANH) - F6-8 (CANL) Ignition switch off 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY BRANCH WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
U127278C02
1.906,1.208 2.229,0.719 true 1.167,4.021 1.479,3.521 true 2.271,4.021 1.948,3.521 true 1.635,0.26 1.927,0.417 0.292,0.156 10 false F6 1.573,2.719 1.865,2.875 0.292,0.156 10 false A42 0.115,0.073 0.406,0.229 0.292,0.156 10 false *a 2.302,0.615 2.719,0.771 0.417,0.156 10 false IG 0.708,3.917 1.167,4.094 0.458,0.177 10 false PGND 2.344,3.917 2.76,4.073 0.417,0.156 10 false PIG
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


a.

Disconnect the power steering ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-1 (PIG) - Body ground Always 11 to 14 V
F6-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (PGND) - Body ground Always Below 1 Ω




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)