Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Combination Meter ECU Communication Stop Mode" are output.

(Click here)


·

Power source or inside combination meter assembly

·

Combination meter assembly main wire or connector

·

Combination meter assembly



WIRING DIAGRAM

E229248E06
1.427,1.042 1.854,1.208 0.427,0.167 10 false CANH 1.427,1.51 1.854,1.677 0.427,0.167 10 false CANL 0.542,1.969 0.948,2.135 0.406,0.167 10 false F83 5.01,0.958 5.219,1.125 0.208,0.167 10 false 32 5.26,1.052 5.688,1.219 0.427,0.167 10 false CANH 5.26,1.49 5.688,1.656 0.427,0.167 10 false CANL 2.333,2.302 3.302,2.615 0.969,0.313 10 false from IG2 Relay 4.177,2.438 4.531,2.656 0.354,0.219 10 false MET 5.26,3.219 5.688,3.385 0.427,0.167 10 false - 5.01,1.406 5.219,1.573 0.208,0.167 10 false 31 1.958,0.948 2.135,1.115 0.177,0.167 10 false 7 1.917,1.406 2.104,1.573 0.188,0.167 10 false 18 5.26,2.281 5.688,2.448 0.427,0.167 10 false IG+ 5.01,2.188 5.219,2.354 0.208,0.167 10 false 39 2.26,1.875 3.292,2.188 1.031,0.313 10 false from MAIN Fuse 3.875,2.042 4.75,2.219 0.875,0.177 10 false ECU-B NO. 2 5.26,1.896 5.688,2.063 0.427,0.167 10 false B 5.01,1.813 5.219,1.979 0.208,0.167 10 false 40 5.01,3.156 5.219,3.323 0.208,0.167 10 false 14 5.26,2.833 5.688,3 0.427,0.167 10 false ET 5.01,2.729 5.219,2.896 0.208,0.167 10 false 21 0.542,2.135 2.167,2.458 1.625,0.323 10 false No. 2 Junction Connector 4.729,3.875 5.115,4.042 0.385,0.167 10 false F1 4.729,4.063 6.604,4.375 1.875,0.313 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
U127157C01
1.781,1.719 1.531,2.083 true 1.896,1.719 2.146,2.083 true 1.635,0.698 1.927,0.854 0.292,0.156 10 false F1 0.135,0.083 0.427,0.24 0.292,0.156 10 false *a 2.219,1.979 2.667,2.167 0.448,0.188 10 false CANH 1.094,1.979 1.5,2.167 0.406,0.188 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


a.

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F1-32 (CANH) - F1-31 (CANL) Ignition switch off 108 to 132 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY MAIN WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
U127159C01
3.104,1.292 2.948,1.625 true 2.406,0.885 2.156,1.458 true 0.469,1.74 0.365,2.073 true 2.76,1.729 2.51,2.063 true 1.625,0.708 1.917,0.865 0.292,0.156 10 false F1 0.135,0.094 0.427,0.25 0.292,0.156 10 false *a 2.219,1.979 2.635,2.135 0.417,0.156 10 false IG+ 0.146,2 0.563,2.156 0.417,0.156 10 false ET 3.125,1.188 3.25,1.344 0.125,0.156 10 false B 2.479,0.781 2.604,0.938 0.125,0.156 10 false -
*a Front view of wire harness connector
(to Combination Meter Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-39 (IG+) - Body ground Ignition switch ON 11 to 14 V
F1-40 (B) - Body ground Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-14 (-) - Body ground Always Below 1 Ω
F1-21 (ET) - Body ground Always Below 1 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)