Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.01–2018.06
RM19S0E _58 Vehicle Interior _063185 PRE-CRASH SAFETY _0307822 PRE-CRASH SAFETY SYSTEM D

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  SYSTEM DESCRIPTION  


PRE-CRASH SAFETY SYSTEM DESCRIPTION


a.

The pre-crash safety system determines the possibility of a collision according to information such as the position of the obstacle and its relative speed, and provides optimal control to avoid the collision and control to reduce the impact during the collision via warnings, brake assist and automatic braking.



FUNCTION OF COMPONENTS


Component Function
Pre-crash Safety City Sensor
·

Acquires information about a preceding vehicle from a monocular camera sensor and laser sensor to perform pre-crash safety system control.

·

Sends the information display, PCS warning light (PCS OFF indicator) and PCS activation indicator signal to the combination meter assembly based on pre-crash safety system control information.

·

Sounds the pre-crash safety city buzzer based on pre-crash safety system control information.


Pre-crash Safety System Cancel Switch Assembly Stops and starts the pre-crash safety system and changes the warning timing.
Pre-crash Safety City Buzzer Sounds according to signals from the pre-crash safety city sensor.
Combination Meter Assembly
·

Displays the pre-crash safety system control status (ON/OFF) and warning timing.

·

During a system malfunction, warns the driver by blinking the PCS warning light (PCS OFF indicator) and sounding the meter buzzer.

·

Sounds to warn the driver in accordance with signals from the pre-crash safety city sensor when the system is malfunctioning.


ECM
·

Detects the shift position signal and accelerator opening angle and sends that information to the pre-crash safety city sensor.

·

Performs engine output control based on information from the pre-crash safety city sensor.


Brake Actuator Assembly (Skid Control ECU)
·

Sends information such as the vehicle speed signal, stop light switch signal and brake control hydraulic pressure to the pre-crash safety city sensor.

·

Performs brake hydraulic pressure and emergency brake signal control based on information from the pre-crash safety city sensor.


Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) Detects the steering angle and steering direction.
Airbag ECU Assembly (Yaw Rate Sensor) Detects the yaw rate and acceleration of the vehicle and transmits signals to the pre-crash safety city sensor.
Main Body ECU (Multiplex Network Body ECU) Sends destination information to the pre-crash safety city sensor.
VSC OFF Switch Disables the pre-crash brake and pre-crash brake assist operation when the switch is turned on.


OUTLINE OF PRE-CRASH SAFETY DETECTION


a.

Collision detection

i.

The system determines in advance the possibility of a collision and whether the collision can be avoided based on road surface conditions and the position and speed of the preceding vehicle according to information about the preceding vehicle from the pre-crash safety city sensor.

HINT:

For details about the system, see "OUTLINE OF PRE-CRASH SAFETY SYSTEM CONTROL" and the function descriptions.



ii.

Component

Component Detection Content
Pre-crash safety city sensor Obstacle in front (vehicle)




OUTLINE OF PRE-CRASH SAFETY SYSTEM CONTROL


Control Condition Start of Control Sender ECU Receiver ECU Operated Parts
Pre-crash warning Collision is possible Pre-crash safety city sensor Combination meter assembly
·

Combination meter assembly (PCS activation indicator)

·

Pre-crash safety city buzzer (warning sound)


Pre-crash brake assist Collision is highly possible Pre-crash safety city sensor
·

Combination meter assembly

·

Brake actuator assembly (skid control ECU)


·

Combination meter assembly (PCS activation indicator)

·

Pre-crash safety city buzzer (warning sound)

·

Brake actuator assembly (skid control ECU)


Pre-crash brake Possibility of a collision is very high Pre-crash safety city sensor
·

Combination meter assembly

·

Brake actuator assembly (skid control ECU)

·

ECM


·

Combination meter assembly (PCS activation indicator)

·

Pre-crash safety city buzzer (warning sound)

·

Brake actuator assembly (skid control ECU)

·

ECM




PRE-CRASH ALARM CONTROL


a.

When the system determines that there is a risk of colliding with an obstacle in front of the vehicle, the PCS activation indicator and the pre-crash safety city buzzer are used to warn the driver to avoid the collision.



PRE-CRASH BRAKE ASSIST CONTROL


a.

When the system determines that there is a risk of colliding with an obstacle in front of the vehicle, brake assist enters standby status and the hydraulic brake pressure is increased to improve braking effectiveness when the driver depresses the brake pedal.



PRE-CRASH BRAKE CONTROL


a.

When the system determines that the possibility of a frontal collision with the vehicle is high, the brakes are operated to reduce the collision speed and reduce the impact during the collision.

NOTICE:

When the system detects that the driver is attempting to cancel operation of the system by performing operations such as the following, pre-crash brake control is canceled.

·

Accelerator pedal is forcefully depressed

·

Steering wheel is operated quickly to avoid a collision




b.

Turning the VSC OFF switch on disables pre-crash brake assist control and pre-crash brake control.

HINT:

After pressing the switch, the PCS activation indicator in the combination meter assembly will illuminate.




PRE-CRASH SAFETY SYSTEM (PCS) OPERATION CONDITIONS


a.

The pre-crash alarm control, pre-crash brake assist control and pre-crash brake control can operate if all of the following conditions are met:

·

Pre-crash safety system is on

·

PCS warning light (PCS OFF indicator) in combination meter assembly does not blink

·

Shift lever is not in R



b.

If the following conditions are met, the pre-crash alarm control will operate:

·

Vehicle speed is between approximately 15 km/h (10 mph) and 140 km/h (87 mph)

·

Relative speed is approximately 15 km/h (10 mph) or more



c.

If the following conditions are met, the pre-crash brake assist control will operate:

·

Vehicle speed is between approximately 30 km/h (19 mph) and 80 km/h (50 mph)

·

Relative speed is approximately 30 km/h (19 mph) or more

·

VSC system is not disabled



d.

If the following conditions are met, the pre-crash brake control will operate:

·

Vehicle speed is between approximately 10 km/h (6 mph) and 80 km/h (50 mph)

·

Relative speed is approximately 10 km/h (6 mph) or more

·

VSC system is not disabled




PRECAUTION FOR PRE-CRASH SAFETY CITY SENSOR


a.

Conditions under which the system may operate even if there is no possibility of a collision.

In the following situations the sensor may detect an object, causing the system to determine that there is a possibility of a frontal collision and operate.

B430758C01
0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 2.417,0.146 2.729,0.302 0.313,0.156 10 false *b 5.104,0.167 5.417,0.323 0.313,0.156 10 false *c 0.198,1.917 0.51,2.073 0.313,0.156 10 false *d 2.729,1.969 3.042,2.125 0.313,0.156 10 false *e 5.083,2 5.396,2.156 0.313,0.156 10 false *f 0.188,3.635 0.5,3.844 0.313,0.208 10 false *g 2.531,3.552 2.844,3.708 0.313,0.156 10 false *h 5.083,3.375 5.396,3.531 0.313,0.156 10 false *i 0.135,5.313 0.448,5.469 0.313,0.156 10 false *j 2.604,5.281 2.917,5.438 0.313,0.156 10 false *k 5.052,5.281 5.365,5.438 0.313,0.156 10 false *l 0.125,7.073 0.438,7.229 0.313,0.156 10 false *m 1.906,7.104 2.219,7.26 0.313,0.156 10 false *n 3.656,7.083 3.969,7.24 0.313,0.156 10 false *o 5.458,7.073 5.771,7.229 0.313,0.156 10 false *p
*a When there is an object (traffic sign, guard rail, etc.) by the roadside at the entrance of a curve *b When passing an oncoming vehicle on a curve
*c When passing an oncoming vehicle while making a left or right turn *d When approaching a low hanging object that may contact the vehicle, such as a banner or tree branches
*e When there is a reflective object, bump, protrusion, etc. on the road surface *f When rapidly closing on a preceding vehicle
*g When rapidly closing on an electric toll gate barrier, parking area barrier, or other barrier that opens and closes *h When approaching an overpass, traffic sign, billboard, etc.
*i When the front part of the vehicle is raised or lowered *j When the sensor is misaligned due to a strong impact being applied to the sensor, etc.
*k When there is a structural object (billboard, street light, etc.) at the top of an uphill road *l When there is a metal object (manhole cover, steel plate, etc.) at the bottom of a downhill road
*m When the vehicle is hit by water or snow from a preceding vehicle, etc. *n When driving through dense fog or smoke
*o When the vehicle is being parked in a place where there is a low hanging object at the height of the pre-crash safety city sensor *p When passing extremely close to an object (stopped vehicle, guardrail, etc.)



b.

Situations in which the pre-crash safety system may not function properly.

The system may not function properly in the following situations:

B417442C03
0.438,0.156 0.75,0.313 0.313,0.156 10 false *a 2.719,0.167 3.031,0.323 0.313,0.156 10 false *b 5.031,0.146 5.344,0.302 0.313,0.156 10 false *c 0.292,1.979 0.604,2.135 0.313,0.156 10 false *d 2.74,1.917 3.052,2.073 0.313,0.156 10 false *e 4.823,1.927 5.135,2.083 0.313,0.156 10 false *f 0.396,3.396 0.698,3.604 0.302,0.208 10 false *g 2.469,3.417 2.781,3.573 0.313,0.156 10 false *h 4.823,3.448 5.135,3.604 0.313,0.156 10 false *i 0.302,4.865 0.615,5.104 0.313,0.24 10 false *j 2.615,4.906 2.938,5.104 0.323,0.198 10 false *k
*a When driving on roads with sharp bends or uneven surfaces *b If a vehicle suddenly moves in front of the vehicle, such as at an intersection
*c If a vehicle suddenly cuts in front of the vehicle *d If the vehicle is skidding
*e When the front part of the vehicle is raised or lowered *f When the windshield is dirty or covered with raindrops, condensation, ice, snow, etc.
*g When the sensor is misaligned due to a strong impact being applied to the sensor, etc. *h When a preceding vehicle is a poor reflector of laser (the rear part of the vehicle lowered, very dirty, etc.)
*i When a very bright light, such as the sun or the headlights of oncoming traffic, shines directly into the pre-crash safety city sensor *j When driving in inclement weather such as heavy rain, fog, snow or a sand storm
*k When the surrounding area is dark, such as while in a tunnel or during nighttime - -




PRE-CRASH SAFETY SYSTEM AUTOMATIC CANCELLATION


a.

When a system malfunction is detected and the sensor cannot detect vehicles, system operation cancels automatically.

HINT:

When the system malfunctions or is temporarily disabled, the PCS warning light (PCS OFF indicator) blinks.