Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.01–2018.06
RM19S0E _58 Vehicle Interior _063185 PRE-CRASH SAFETY _0307822 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / (desired system) / Data List.


e.

Read the Data List according to the display on the GTS.

PCS/LDA/RSA/LVN
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Lidar Detect Target Distance Displays distance of the highest priority object which is detected by Lidar / 0 to 51 m. Distance between the vehicle and a preceding vehicle
·

When no preceding vehicle is detected, "0 m" (0 ft.) is displayed

·

Displays the distance between the pre-crash safety city sensor (laser sensor) and a preceding vehicle.


Headlight Type Displays headlight type / Halogen, HID or LED Halogen: Vehicle equipped with halogen headlights
HID: Vehicle equipped with HID headlights
LED: Vehicle equipped with LED headlights
-
PCS Buzzer Demand Displays pre-crash safety city buzzer condition / ON or OFF ON: Pre-crash safety city buzzer active
OFF: Pre-crash safety city buzzer inactive
-
Skid Control Buzzer Demand Displays lane departure alert buzzer / ON or OFF ON: Lane departure alert buzzer active
OFF: Lane departure alert buzzer inactive
Buzzer request when lane departure alert system enabled and vehicle deviated from white line
RSA Fusion Control - - This item is displayed on the GTS but is not used
Traffic Sign Speed Unit - - This item is displayed on the GTS but is not used
RSA Equipped Information - - This item is displayed on the GTS but is not used
Estimated Traffic Division - - This item is displayed on the GTS but is not used
Estimated Traffic Division Displays estimated traffic division - This item is displayed on the GTS but is not used
LVN Equipped Information Displays whether vehicle equipped with LVN / ON or OFF ON: Vehicle equipped with LVN
OFF: Vehicle not equipped with LVN
This item is displayed on the GTS but is not used
History of Blockage Displays whether there is camera or laser sensor obstruction history / ON or OFF ON: Pre-crash safety city sensor (camera) obstruction history exists
OFF: Pre-crash safety city sensor (camera) obstruction history does not exist
-
History of Low Voltage Displays whether there is low voltage history / ON or OFF ON: Pre-crash safety city sensor low voltage history exists
OFF: Pre-crash safety city sensor low voltage history does not exist
-
History of High Voltage Displays whether there is high voltage history / ON or OFF ON: Pre-crash safety city sensor high voltage history exists
OFF: Pre-crash safety city sensor high voltage history does not exist
-
History of Low Temperature Displays whether there is low temperature history / ON or OFF ON: Pre-crash safety city sensor low temperature history exists
OFF: Pre-crash safety city sensor low temperature history does not exist
-
History of High Temperature Displays whether there is high temperature history / ON or OFF ON: Pre-crash safety city sensor high temperature history exists
OFF: Pre-crash safety city sensor high temperature history does not exist
-
Blockage Status Displays whether there is a camera obstruction malfunction / ON or OFF ON: Pre-crash safety city sensor (camera) obstructed
OFF: Pre-crash safety city sensor (camera) not obstructed
-
Low Voltage Status Displays whether there is a low voltage malfunction / ON or OFF ON: Pre-crash safety city sensor low voltage malfunction exists
OFF: Pre-crash safety city sensor low voltage malfunction does not exist
-
High Voltage Status Displays whether there is a high voltage malfunction / ON or OFF ON: Pre-crash safety city sensor high voltage malfunction exists
OFF: Pre-crash safety city sensor high voltage malfunction does not exist
-
Low Temperature Status Displays whether there is a low temperature malfunction / ON or OFF ON: Pre-crash safety city sensor low temperature malfunction exists
OFF: Pre-crash safety city sensor low temperature malfunction does not exist
-
High Temperature Status Displays whether there is a high temperature malfunction / ON or OFF ON: Pre-crash safety city sensor high temperature malfunction exists
OFF: Pre-crash safety city sensor high temperature malfunction does not exist
-
Lidar Blockage Status Displays whether laser sensor is dirty / ON or OFF ON: Dirt on pre-crash safety city sensor (laser sensor)
OFF: No dirt on pre-crash safety city sensor (laser sensor)
-
Control Mode Displays ECU control mode status / Normal or Check Mode Normal: Normal operation Check Mode: Operating in control mode -
PCS Operation State Retention Setting Displays the setting of the PCS Operation State Retention Setting customize setting / ON or OFF ON: PCS Operation State Retention Setting customize setting is set to ON
OFF: PCS Operation State Retention Setting customize setting is set to OFF
-
PCS Alarm Activation Distance Retention Setting 1 Displays the setting of the PCS Alarm Activation Distance Retention Setting 1 customize setting / ON or OFF ON: PCS Alarm Activation Distance Retention Setting 1 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 1 customize setting is set to OFF
-
PCS Alarm Activation Distance Retention Setting 2 Displays the setting of the PCS Alarm Activation Distance Retention Setting 2 customize setting / ON or OFF ON: PCS Alarm Activation Distance Retention Setting 2 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 2 customize setting is set to OFF
-
PCS Alarm Activation Distance Retention Setting 3 Displays the setting of the PCS Alarm Activation Distance Retention Setting 3 customize setting / ON or OFF ON: PCS Alarm Activation Distance Retention Setting 3 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 3 customize setting is set to OFF
-
The Number of DTCs Number of trouble codes / 0 to 255 Number of DTCs will be displayed -

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch status / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Stop Light Relay Output Stop light switch assembly output / ON or OFF ON: Stop light switch assembly output on (Stop light on)
OFF: Stop light switch assembly output off (Stop light off)
-



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / (desired system) / Active Test.


e.

Perform Active Test according to the display on the GTS.

HINT:

The ignition switch must be turned to ON to proceed with the Active Test using the GTS.


PCS/LDA/RSA/LVN
Tester Display Test Part Control Range Diagnostic Note
PCS Buzzer Request Sounds pre-crash safety city buzzer ON/OFF Test possible with ignition switch ON, vehicle stopped
Meter Buzzer Request Sounds meter buzzer ON/OFF Test possible with ignition switch ON, vehicle stopped
Automatic High Beam Operates automatic high beam system ON/OFF Test possible with ignition switch ON, engine stopped (operation possible regardless of system restrictions such as vehicle speed, shift position)

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Switches stop light ON/OFF Possible at vehicle speed of 0 km/h (0 mph)

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Precrash PCS Warning Light (PCS OFF Indicator) ON/OFF -
PCS Warning Indicator PCS activation indicator ON/OFF -