DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / PCS/LDA/RSA/LVN / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Lidar Detect Target Distance | Displays distance of the highest priority object which is detected by Lidar / 0 to 51 m. | Distance between the vehicle and a preceding vehicle | ·
When no preceding vehicle is detected, "0 m" (0 ft.) is displayed ·
Displays the distance between the pre-crash safety city sensor (laser sensor) and a preceding vehicle. |
| Headlight Type | Displays headlight type / Halogen or LED | Halogen: Vehicle equipped with halogen headlights
LED: Vehicle equipped with LED headlights |
- |
| PCS Buzzer Demand | Displays pre-crash safety buzzer condition / ON or OFF | ON: Pre-crash safety buzzer active
OFF: Pre-crash safety buzzer inactive |
- |
| Skid Control Buzzer Demand | Displays lane departure alert buzzer condition / ON or OFF | ON: Lane departure alert buzzer active
OFF: Lane departure alert buzzer inactive |
Buzzer request when lane departure alert system enabled and vehicle deviated from white line |
| RSA Fusion Control | - | - | This item is displayed on the GTS but is not used |
| Traffic Sign Speed Unit | - | - | This item is displayed on the GTS but is not used |
| LVN Equipped Information | Displays whether vehicle equipped with LVN / ON or OFF | ON: Vehicle equipped with LVN
OFF: Vehicle not equipped with LVN |
- |
| History of Blockage | Displays whether there is pre-crash safety city sensor obstruction history / ON or OFF | ON: Pre-crash safety city sensor (camera) obstruction history exists
OFF: Pre-crash safety city sensor (camera) obstruction history does not exist |
- |
| History of Low Voltage | Displays whether there is low voltage history / ON or OFF | ON: Pre-crash safety city sensor low voltage history exists
OFF: Pre-crash safety city sensor low voltage history does not exist |
- |
| History of High Voltage | Displays whether there is high voltage history / ON or OFF | ON: Pre-crash safety city sensor high voltage history exists
OFF: Pre-crash safety city sensor high voltage history does not exist |
- |
| History of Low Temperature | Displays whether there is low temperature history / ON or OFF | ON: Pre-crash safety city sensor low voltage history exists
OFF:Pre-crash safety city sensor low voltage history does not exist |
- |
| History of High Temperature | Displays whether there is high temperature history / ON or OFF | ON: Pre-crash safety city sensor high temperature history exists
OFF: Pre-crash safety city sensor high temperature history does not exist |
- |
| Blockage Status | Displays whether there is a camera obstruction malfunction / ON or OFF | ON: Pre-crash safety city sensor (camera) obstructed
OFF: Pre-crash safety city sensor (camera) not obstructed |
- |
| Low Voltage Status | Displays whether there is a low voltage malfunction / ON or OFF | ON: Pre-crash safety city sensor low voltage malfunction exists
OFF: Pre-crash safety city sensor low voltage malfunction does not exist |
- |
| High Voltage Status | Displays whether there is a high voltage malfunction / ON or OFF | ON: Pre-crash safety city sensor high voltage malfunction exists
OFF: Pre-crash safety city sensor high voltage malfunction does not exist |
- |
| Low Temperature Status | Displays whether there is a low temperature malfunction / ON or OFF | ON: Pre-crash safety city sensor low temperature malfunction exists
OFF: Pre-crash safety city sensor low temperature malfunction does not exist |
- |
| High Temperature Status | Displays whether there is a high temperature malfunction / ON or OFF | ON: Pre-crash safety city sensor high temperature malfunction exists
OFF: Pre-crash safety city sensor high temperature malfunction does not exist |
- |
| Lidar Blockage Status | Displays whether laser sensor is dirty / ON or OFF | ON: Dirt on pre-crash safety city sensor (laser sensor)
OFF: No dirt on pre-crash safety city sensor (laser sensor) |
- |
| Control Mode | Displays ECU control mode status / Normal or Check Mode | Normal: Normal operation
Check: Operating in Control Mode |
- |
| PCS Operation State Retention Setting | Displays the setting of the PCS Operation State Retention Setting customize setting / ON or OFF | ON: PCS Operation State Retention Setting customize setting is set to ON
OFF: PCS Operation State Retention Setting customize setting is set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 1 | Displays the setting of the PCS Alarm Activation Distance Retention Setting 1 customize setting / ON or OFF | ON: PCS Alarm Activation Distance Retention Setting 1 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 1 customize setting is set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 2 | Displays the setting of the PCS Alarm Activation Distance Retention Setting 2 customize setting / ON or OFF | ON: PCS Alarm Activation Distance Retention Setting 2 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 2 customize setting is set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 3 | Displays the setting of the PCS Alarm Activation Distance Retention Setting 3 customize setting / ON or OFF | ON: PCS Alarm Activation Distance Retention Setting 3 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 3 customize setting is set to OFF |
- |
| The Number of DTCs | Number of trouble codes / 0 to 255 | Number of DTCs will be displayed | - |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / PCS/LDA/RSA/LVN / Active Test.
Perform Active Test according to the display on the GTS.
The ignition switch must be turned to ON to proceed with the Active Test using the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Buzzer Request | Sounds pre-crash safety city buzzer | ON/OFF | Test possible with ignition switch ON, vehicle stopped |
| Meter Buzzer Request | Sounds meter buzzer | ON/OFF | Test possible with ignition switch ON, vehicle stopped |
| Automatic High Beam | Operates automatic high beam system | ON/OFF | This Active Test can only be performed when the ignition switch is ON, the vehicle is stopped and the area around the vehicle is dark. (Normal system operation conditions, such as vehicle speed and shift lever position, do not need to be met.) |