TERMINALS OF ECU
| *a | Component without harness connected
(Skid Control ECU (Brake Actuator Assembly)) |
| Terminal No. (Symbol) | Terminal Description |
|---|---|
| 1 (GND1) | Skid control ECU ground |
| 2 (STP) | Stop light switch assembly input |
| 4 (RL-) | Rear wheel speed LH (-) signal input |
| 5 (RL+) | Rear wheel speed LH (+) power supply output |
| 6 (FR-) | Front wheel speed RH (-) signal input |
| 7 (FR+) | Front wheel speed RH (+) power supply output |
| 11 (SP1) | Speed signal output for speedometer |
| 12 (+BS) | Solenoid relay power supply |
| 13 (GND2) | Pump motor ground |
| 14 (CANL) | CAN communication line L |
| 16 (RR-) | Rear wheel speed RH (-) signal input |
| 17 (RR+) | Rear wheel speed RH (+) power supply output |
| 18 (FL-) | Front wheel speed LH (-) signal input |
| 19 (FL+) | Front wheel speed LH (+) power supply output |
| 22 (STP2)*1 | Stop light switch assembly input*1 |
| 24 (BM) | Motor relay power supply |
| 25 (CANH) | CAN communication line H |
| 27 (EXI3) | Back-up light switch assembly input |
| 30 (CSW) | VSC OFF switch input |
| 31 (STPO)*1 | Stop light switch assembly output*1 |
| 34 (IG1) | ECU power supply |
*1: w/ Toyota Safety Sense
TERMINAL INSPECTION
Disconnect the connector and measure the voltage or resistance on the wire harness side.
Voltage cannot be measured with the connector connected to the brake actuator assembly (skid control ECU) as the connector is watertight.
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A54-1 (GND1) - Body ground | W-B - Body ground | Skid control ECU ground | Always | Below 1 Ω |
| A54-2 (STP) - Body ground | LG - Body ground*1
R - Body ground*2 |
Stop light switch assembly input | Stop light switch assembly ON → OFF
(Brake pedal depressed → released) |
7.5 to 14 V
→ Below 1.5 V |
| A54-12 (+BS) - Body ground | W - Body ground | Solenoid relay power supply | Always | 11 to 14 V |
| A54-13 (GND2) - Body ground | W-B - Body ground | Pump motor ground | Always | Below 1 Ω |
| A54-22 (STP2) - Body ground*1 | R - Body ground | Stop light switch assembly input | Stop light switch assembly ON → OFF (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| A54-24 (BM) - Body ground | B - Body ground | Motor relay power supply | Always | 11 to 14 V |
| A54-25 (CANH) - A54-14 (CANL) | G - W | CAN bus | Ignition switch off | 54 to 69 Ω |
| A54-30 (CSW) - Body ground | B - Body ground | VSC OFF switch input | VSC OFF switch held ON → OFF (Not pressed) | Below 25 Ω → 10 kΩ or higher |
| A54-31 (STPO) - Body ground*1 | V - Body ground | Stop light switch assembly output | Ignition switch ON | 11 to 14 V |
| A54-34 (IG1) - Body ground | G - Body ground | ECU power supply | Ignition switch ON | 11 to 14 V |
*1: w/ Toyota Safety Sense
*2: w/o Toyota Safety Sense