Home › Vehicle Interior › PRE-CRASH SAFETY › FRONT SENSOR › from 2017.01
RM19S0E _58 Vehicle Interior _063185 PRE-CRASH SAFETY _0309286 FRONT SENSOR A

PRE-CRASH SAFETY  FRONT SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

The pre-crash safety city sensor uses lasers to detect preceding vehicles. The pre-crash safety city sensor is classified as a Class 1M laser product according to the IEC 60825-1 standard.

These lasers are not harmful to the naked eye. However, it is necessary to observe the following precautions. Failure to do so may result in severe visual impairment, or at worst, loss of eyesight.

·

To avoid hazardous laser radiation exposure, never attempt to disassemble the pre-crash safety city sensor or perform maintenance procedures that are not described in the repair manual. When disassembled, the pre-crash safety city sensor is classified as a Class 3B laser product according to the IEC 60825-1 standard and poses an eye injury risk.

·

When removing the pre-crash safety city sensor, always disconnect the connector first.

·

Do not look into the pre-crash safety city sensor using a magnifying glass, microscope or other optical instrument from a distance of 100 mm (3.94 in.) or less.

·

As the pre-collision city sensor may be hot, be careful not to burn or injure yourself.


E347984C13
0.49,0.167 0.917,0.51 0.427,0.344 12 false *1 0.5,2.75 0.969,3.167 0.469,0.417 12 false *2
*1 Laser Classification Label *2 Laser Explanatory Label


Laser Emission Data
Maximum average power 45 mW
Pulse duration 33 ns
Wavelength 905 nm
Divergence (horizontal X vertical) 28°X12°


NOTICE:
·

When replacing the pre-crash safety city sensor, replace it with a new one.

·

Do not touch the camera lens or the front windshield glass in front of the camera.

·

If the pre-crash safety city sensor has been struck or dropped, replace it with a new one.

·

When replacing the windshield glass of a vehicle equipped with a pre-crash safety city sensor, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the pre-crash safety city sensor may not be able to be installed due to a missing bracket or the pre-crash safety system may not operate properly due to a difference in the transmissivity of the windshield glass or the shape of the black ceramic border.



PROCEDURE

Hide 88184 1.REMOVE PRE-CRASH SAFETY CITY COVER 2ND

a.
E320924

Disengage the 2 claws and 2 guides to remove the pre-crash safety city cover 2nd as shown in the illustration.

NOTICE:

If these claws are disengaged separately, they may break. Insert a molding remover between them and pull it down to disengage the claws simultaneously.



Hide 88183 2.REMOVE PRE-CRASH SAFETY CITY COVER

a.
E320925

Disengage the 2 clips and 2 guides to remove the pre-crash safety city cover as shown in the illustration.

HINT:

To avoid damaging the guides, always slide the pre-crash safety city cover parallel to the windshield glass.



Hide 88181 3.REMOVE PRE-CRASH SAFETY CITY SENSOR

a.
E320926

Disconnect the connector.

NOTICE:

Do not pull the harness forcibly when disconnecting the connector.



b.
E320927

Disengage the 2 claws to separate the rear side of pre-crash safety city sensor.

NOTICE:
·

If the pre-crash safety city bracket is deformed or damaged, replace it together with the windshield glass.

·

If the pre-crash safety city sensor has been struck or dropped, replace it with a new one.

·

Do not touch the camera lens.

·

Do not apply excessive force.




c.

Disengage the 2 guides to remove the pre-crash safety city sensor as shown in the illustration.