Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM › from 2017.01
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0309752 AUTOMATIC HIGH BEAM SYSTEM U

LIGHTING (EXT)  AUTOMATIC HIGH BEAM SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU


E364861C04
3.635,0.979 3.969,1.167 0.333,0.188 0.5,1.021 0.833,1.208 0.333,0.188 0.5,1.688 0.833,1.875 0.333,0.188 0.5,2.26 0.833,2.448 0.333,0.188 3.667,2.896 4,3.083 0.333,0.188 6.25,0.979 6.583,1.167 0.333,0.188 6.24,1.729 6.573,1.917 0.333,0.188 1.396,3.917 1.729,4.104 0.333,0.188 3.979,3.885 4.313,4.073 0.333,0.188 5.979,3.896 6.313,4.083 0.333,0.188 1.583,5.177 1.917,5.365 0.333,0.188 5.313,5.219 5.646,5.406 0.333,0.188 1.146,6.677 1.531,6.885 0.385,0.208 1.885,6.677 2.26,6.885 0.375,0.208 5.469,6.677 5.844,6.885 0.375,0.208 1.573,7.615 1.979,7.844 0.406,0.229 5.115,7.594 5.521,7.823 0.406,0.229 0.583,1.052 0.844,1.219 0.26,0.167 10 false 3D 0.188,0.198 0.51,0.385 0.323,0.188 10 false *1 0.594,1.719 0.854,1.885 0.26,0.167 10 false 3C 0.583,2.292 0.844,2.458 0.26,0.167 10 false 3F 3.719,1 3.979,1.167 0.26,0.167 10 false MB 3.75,2.917 4.01,3.083 0.26,0.167 10 false MB 6.323,1 6.583,1.167 0.26,0.167 10 false 3B 6.323,1.75 6.583,1.917 0.26,0.167 10 false 3A 1.5,3.938 1.76,4.104 0.26,0.167 10 false 3D 4.063,3.906 4.323,4.073 0.26,0.167 10 false 3C 6.073,3.927 6.333,4.094 0.26,0.167 10 false 3F 5.406,5.24 5.667,5.406 0.26,0.167 10 false 3A 1.667,5.198 1.927,5.365 0.26,0.167 10 false 3B 1.198,6.708 1.594,6.885 0.396,0.177 10 false F136 1.958,6.698 2.26,6.875 0.302,0.177 10 false F76 0.167,6.365 0.49,6.552 0.323,0.188 10 false *2 0.292,6.74 0.615,6.927 0.323,0.188 10 false *A 3.771,6.75 4.094,6.938 0.323,0.188 10 false *B 5.542,6.698 5.844,6.875 0.302,0.177 10 false F76 1.635,7.646 2.031,7.823 0.396,0.177 10 false F136 5.219,7.635 5.615,7.813 0.396,0.177 10 false F76
*A Main Body ECU 2 Connector Type *B Main Body ECU 1 Connector Type
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Remove the main body ECU (multiplex network body ECU) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-30 (BECU) - Body ground - Battery power supply Ignition switch off 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
MB-11 (GND1) - Body ground - Body ground Always Below 1 Ω


c.

Reinstall the main body ECU (multiplex network body ECU) connectors.


d.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3C-35 (DIM) - 3B-8 (GND1) P - W-B Dimmer relay drive output Dimmer switch in high or high flash position Below 1 V
Dimmer switch not in high or high flash position 11 to 14 V
F76-5 (HU) - 3B-8 (GND1) P - W-B Dimmer switch high position signal input Dimmer switch in high or high flash position Below 1 V
Dimmer switch in low position 11 to 14 V
F76-29 (HEAD) - Body ground L - Body ground Light control switch head position input Light control switch in head position Below 1 V
Light control switch not in head position, ignition switch off Pulse generation
Light control switch not in head position, ignition switch ON 11 to 14 V
F76-3 (AHBI) - Body ground*1
F136-5 (AHBI) - Body ground*2
GR - Body ground Combination switch assembly (automatic high beam switch) signal input Ignition switch on, combination switch assembly (automatic high beam switch) on Below 1 V
Ignition switch on, combination switch assembly (automatic high beam switch) off 11 to 14 V
F76-14 (CANH) - Body ground R - Body ground CAN communication line Ignition switch ON Pulse generation
F76-13 (CANL) - Body ground W - Body ground CAN communication line Ignition switch ON Pulse generation
F76-21 (CLTS) - 3B-8 (GND1)*3 B - W-B Automatic light control sensor signal input Ignition switch ON Below 1 V
With the ignition switch ON and the light control switch in the AUTO position, cover the top of the automatic light control sensor with a lightproof object, and then expose the sensor Pulse generation (waveform varies depending on light volume) (Waveform 1)
F76-28 (A) - 3B-8 (GND1)*3 V - W-B Light control switch AUTO position signal input Light control switch in AUTO position Below 1 V
Light control switch not in AUTO position 11 to 14 V

*1: for Halogen Headlight

*2: for LED headlight

*3: w/ Automatic Light Control System


If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.

i.
E141421E01
2.937,1.016 3.278,1.181 0.341,0.165 10 GND 1.86,1.394 1.988,1.559 0.128,0.165 10 A

Waveform 1 (w/ Automatic Light Control System)

Item Content
Terminal No. (Symbol) F76-21 (CLTS) - 3B-8 (GND1)
Tool setting 5 V/DIV., 5 ms/DIV.
Condition With the ignition switch ON and the light control switch in the AUTO position, cover the top of the automatic light control sensor with a lightproof object, and then expose the sensor

HINT:

The brighter the surrounding area, the narrower width A becomes.





PRE-CRASH SAFETY CITY SENSOR