AUTOMATIC HIGH BEAM SYSTEM
General
The automatic high beam system enhances the illumination of the area to the front of the vehicle to improve visibility for the driver. It works by detecting light from the front of the vehicle, using the pre-crash safety city sensor, and turns the high beam headlights on or off automatically.
Function of Main Components
| Component | Outline |
|---|---|
| Pre-crash Safety City Sensor | Determines when to turn the high beam headlights on and off after identifying the lights of oncoming vehicles, preceding vehicles and other lights from the picture information of its camera sensor. Then, it sends high beam request signals to the main body ECU (multiplex network body ECU) via CAN communication. |
| Airbag ECU Assembly (Yaw Rate Sensor) | Outputs yaw rate information to the pre-crash safety city sensor. |
| Brake Actuator Assembly (Skid Control ECU) | Outputs information about the speed of the 4 wheels. This information is used by the pre-crash safety city sensor to turn the high beam headlights on and off. |
| Combination Meter Assembly | Displays the automatic high beam indicator light when it receives illuminate request signals from the main body ECU (multiplex network body ECU).
|
| Main Body ECU (Multiplex Network Body ECU) | ·
Determines whether the automatic high beam system is in standby mode based on a dimmer switch high position signal, light control switch AUTO*1 or head position signal and combination switch assembly (automatic high beam switch) signal, and sends an indicator illumination request signal to the combination meter assembly. ·
Receives the high beam illumination request signal from the pre-crash safety city sensor and changes between the high beam headlights and low beam headlights. ·
Performs illumination control for the automatic high beam system and stores Diagnostic Trouble Codes (DTCs) when the system malfunctions. |
| Combination Switch Assembly (Automatic High Beam Switch) | Enables or disables the automatic high beam system. |
*1: w/ Automatic Light Control System
Basic Function
When all of the following conditions are met, the automatic high beam system is activated and the automatic high beam indicator light turns on:
Ignition switch ON.
The light control switch is in the AUTO*1 or head position and the low beam headlights are on.
The dimmer switch is in the high position.
The combination switch assembly (automatic high beam switch) is on.
*1: w/ Automatic Light Control System
When all of the following conditions are met, the high beam headlights automatically turn on after a short delay:
Vehicle speed is more than approximately 34 km/h (21 mph).
The area in front of the vehicle is dark.
There are no oncoming vehicles with headlights on.
There are no preceding vehicles with taillights on.
There are few streetlights along the street ahead.
When any of the following conditions are met, the high beam headlights automatically turn off after a short delay:
Vehicle speed is less than approximately 27 km/h (17 mph).
There are oncoming vehicles with headlights on.
There are preceding vehicles with taillights on.
Light from streetlights ahead is higher than a specified threshold.
When any of the following conditions are met, the automatic high beam system will be canceled and the indicator light will turn off:
The ignition switch is turned off.
The light control switch is turned to any position except the AUTO*1 and head position.
The low beam headlights are turned off.
The dimmer switch is moved to the low position.
The combination switch assembly (automatic high beam switch) is off.
*1: w/ Automatic Light Control System
It is possible to manually turn the high beam headlights on and off using either of the following operations:
When changing the high beam headlights controlled by the automatic high beam system to the low beam headlights manually, move the dimmer switch to the low position. The automatic high beam system will be canceled and the low beam headlights will be turned on. To enable the automatic high beam system again, move the dimmer switch to the high position.
When changing the low beam headlights controlled by the automatic high beam system to the high beam headlights manually, turn the combination switch assembly (automatic high beam switch) off. The automatic high beam system will be canceled and the high beam headlights will be turned on. To enable the automatic high beam system again, turn the combination switch assembly (automatic high beam switch) on.
The automatic high beam system monitors the area in front of the vehicle using the pre-crash safety city sensor and makes a judgment to turn the high beam headlights when the surrounding area is dark (there are no headlights from oncoming vehicles and no taillights from preceding vehicles). High beam control limitations:
When the surrounding area is not dark enough, the high beam headlights will not turn on even if the low beam headlights are turned on by the automatic light control system and the automatic high beam indicator light on the combination meter assembly is illuminated. (The light level sufficient to turn the auto low beam headlights on is not the same as the light level required to automatically change the low beam headlights to high beam headlights.)
When an oncoming vehicle suddenly appears at a sharp curve or a vehicle crosses the path of the vehicle, the high beam headlights may remain on.
When the fog lights of an oncoming vehicle are detected, the high beam headlights may be turned off.
The timing of the high beam headlights turning on and off may differ depending on the brightness of headlights or fog lights from oncoming vehicles or the taillights of preceding vehicles.
The timing of the high beam headlights turning on and off may differ between normal conditions (good weather) and when driving on wet, frozen or snowy roads.
The timing of the high beam headlights turning on and off may differ depending on the number of occupants and amount of cargo present.
Be aware that on some occasions, the high beam headlights may switch on and off unexpectedly.
When the taillights of a preceding vehicle are off in a tunnel or at night, the high beam headlights may not be turned off.
The pre-crash safety city sensor continually monitors the light level in the area to the front of the vehicle. There is a delay in turning on the high beam headlights. Even when there is no ambient light, the high beam headlights will not turn on immediately. The delay will vary depending on the situation.